Hi,
ich habe mein Problem auch bei der Maillist von ivtv beschrieben, bislang hat da noch keiner einen brauchbaren Lösungsvorschlag anzubieten.
Ich habe einen Epia SP 13000, eine PVR 350, eine TT DVB-C 2.1.
Zwei Partitionen:
Auf der einen funktioniert vdr 1.3.37 mit ivtv 0.4 und kernel linux-2.6.14-gentoo-r4, ich kann mit vdr durch das analoge Programm problemlos zappen.
Auf der zweiten habe ich ein neues Gentoo mit dem kernel 2.6.17-r7 aufgezogen, ivtv 0.7, vdr 1.4.1 und pvrinput neben anderem mit emerge installiert.
Irgendwas klappt da nicht, dmesg bringt:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.7.0 (tagged release) loading
ivtv: Linux version: 2.6.17-gentoo-r7 mod_unload VIAC3-2 REGPARM gcc-4.1
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: Failed to load module tveeprom
tveeprom 1-0050: Hauppauge model 48134, rev J342, serial# 7067564
tveeprom 1-0050: tuner model is Temic 4009FR5 (idx 42, type 20)
tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 1-0050: audio processor is MSP4418 (idx 25)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has radio, has IR remote
ivtv0: Failed to load module tuner
ivtv0: Failed to load module tda9887
ivtv0: Failed to load module saa7115
ivtv0: Failed to load module saa7127
ivtv0: Failed to load module msp3400
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c addr 0x21 not found for command 0x4008646f!
ivtv0: i2c hardware 0x00000008 not found for command 0x4008646d!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ivtv: ==================== END INIT IVTV ====================
Alles anzeigen
Für vdr habe ich die channels.conf der funktionierenden Partition hergenommen. Durch die digitalen Kanäle kann ich problemlos zappen, jedesmal wenn ich durch die analogen Kanäle zappe, erscheint diese Meldung im Systemlog:
Sep 10 13:13:06 digi ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
Sep 10 13:13:06 digi ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
Ich habe die ganzen Einstellungen im .config überprüft, ich habe dabei praktisch dieselben Einstellungen übernommen, die Module (tveeprom, tuner, tda9887, saa7115, saa7127, msp3400) werden auch richtig erzeugt und liegen im entsprechenden Kernel-Verzeichnis.
Ich habe auch einiges rumexperimentiert, immer mit dem selben Resultat.
Das einzige was mir noch auffällt ist diese Meldung, die gabs vorher nicht:
Hat einer eine Idee was ich machen muß?
Danke