Hallo,
ich bin besagte Schwester von ryhmes um deren vdr es hier geht. Vielen Dank für deine Hilfe, ich hab den Kernel auf den von dir gelinkten umgestellt und auch das mit den tveeprom.ko gemacht, nur ist jetzt die Anzeige am TV ganz weg. (Am Kabel o.ä. liegt es nicht, beim booten bekomme ich kurz einen grünen Schirm.)
Beim booten findet er jetzt allerdings auch ne Menge nicht, darunter tveeprom. Aber genug der umständlichen Erklärung, hier die dmesg:
Code
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 LAN0 AC97 MC97 UAR1
ACPI: (supports S0 S1 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 164k freed
EXT3 FS on hda1, internal journal
cdfs 2.6.12 loaded.
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000d800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 12, io base 0x0000dc00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 5, io mem 0xe2000000
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
hub 4-0:1.0: over-current change on port 5
hub 4-0:1.0: over-current change on port 6
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 12 (level, low) -> IRQ 12
PCI: Setting latency timer of device 0000:00:11.5 to 64
Adding 262136k swap on /var/vm/swapfile. Priority:-1 extents:67 across:266580k
i2c /dev entries driver
lirc_dev: IR Remote Control driver registered, at major 61
lirc_i2c: no version for "lirc_unregister_plugin" found: kernel tainted.
Linux video capture interface: v1.00
bttv: Unknown symbol tveeprom_read
bttv: Unknown symbol tveeprom_hauppauge_analog
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.2 (development snapshot compiled on Mi 04 Jan 2006 22:17:35 CET) loading
ivtv: Linux version: 2.6.14.2 386 gcc-3.3
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (cx23415 based)
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ivtv0: Failed to load module tveeprom
ivtv0 warning: i2c client addr: 0x50 not found for command 0x0!
ivtv0: Error -19 reading Hauppauge eeprom.
ivtv0: Possible causes: the tveeprom module was not loaded, or
ivtv0: the eeprom kernel module was loaded before the tveeprom module.
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
saa7115 0-0021: ivtv driver
saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
saa7127 0-0044: ivtv driver
saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
msp3400 0-0040: ivtv driver
msp3400 0-0040: chip=MSPB4255O-?31 +nicam +simple +simpler +radio mode=simpler
ivtv0: i2c attach to card #0 ok [client=MSPB4255O-?31, addr=40]
msp3400 0-0040: msp34xxg daemon started
tda9887 0-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: Could not detect tuner standard, defaulting to NTSC.
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
tuner: tuner type not set
ivtv0: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV ====================
cx88xx: Unknown symbol tveeprom_read
cx88xx: Unknown symbol tveeprom_hauppauge_analog
cx8800: Unknown symbol cx88_reset
cx8800: Unknown symbol cx88_call_i2c_clients
cx8800: Unknown symbol cx88_wakeup
cx8800: Unknown symbol cx88_risc_stopper
cx8800: Unknown symbol cx88_print_irqbits
cx8800: Unknown symbol cx88_set_scale
cx8800: Unknown symbol cx88_shutdown
cx8800: Unknown symbol cx88_vdev_init
cx8800: Unknown symbol cx88_core_put
cx8800: Unknown symbol cx88_audio_thread
cx8800: Unknown symbol cx88_core_irq
cx8800: Unknown symbol cx88_core_get
cx8800: Unknown symbol cx88_get_stereo
cx8800: Unknown symbol cx88_set_tvnorm
cx8800: Unknown symbol cx88_risc_buffer
cx8800: Unknown symbol cx88_set_stereo
cx8800: Unknown symbol cx88_sram_channels
cx8800: Unknown symbol cx88_set_tvaudio
cx8800: Unknown symbol cx88_sram_channel_dump
cx8800: Unknown symbol cx88_sram_channel_setup
cx8800: Unknown symbol cx88_free_buffer
cx8800: Unknown symbol cx88_boards
cx8800: Unknown symbol cx88_newstation
lirc_i2c: chip found @ 0x18 (Hauppauge IR)
ivtv0: i2c attach to card #0 ok [client=Hauppauge IR, addr=18]
lirc_dev: lirc_register_plugin: sample_rate: 10
ivtv0-osd: Framebuffer module loaded (attached to ivtv card id 0)
ivtv0-osd warning: Framebuffer is at decoder-relative address 0x00510000 and has 1704960 bytes.
ivtv0-osd: screen coords: [0 0] -> [720 480]
ivtv0-osd: original global alpha = 208
ivtv0-osd: current OSD state = 39
spurious 8259A interrupt: IRQ7.
ivtv0-osd: new global alpha = 208 (1 255 0)
ivtv0-osd: framebuffer at 0xdd510000, mapped to 0xdfa10000, size 1350k
ivtv0-osd: mode is 720x480x32, linelength=2880
Console: switching to colour frame buffer device 90x30
ivtv0-osd: fb0: cx23415 TV out frame buffer device
ivtv0: Allocate DMA decoder OSD stream: 16 x 65536 buffers (1024KB total)
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0xe2001000, 00:40:63:d5:97:4d, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
lirc_serial: auto-detected active high receiver
lirc_dev: lirc_register_plugin: sample_rate: 0
Alles anzeigen
lg,
shiny