Hallo, ich habe mir ein Raspberry CM4 mit IO Board gegönnt um mit einer Cine S2 V6.5 einen kleinen VDR Server zu bauen.
Ich konnte den Treiber von DD auch ohne Fehler bauen, und die Karte wird richtig erkannt, nur leider bekomme ich keine Sender
w_scan2
Code
initial_tune:3331: Setting frontend failed S f = 12692 kHz H SR = 22000 5/6 0,35 QPSK (0:0:0)
trying 'S2 f = 12699 kHz V SR = 22000 2/3 0,35 8PSK (0:0:0)'
(time: 00:49.549) set_frontend:2671: ERROR: Setting frontend parameters failed
: 22 Invalid argument
dmesg | grep -i dvb
Code
[ 4.584829] dvb_core: loading out-of-tree module taints kernel.
[ 4.628851] ddbridge 0000:01:00.0: device name: Digital Devices Cine S2 V6.5 DVB adapter
[ 4.633621] ddbridge 0000:01:00.0: Port 0: Link 0, Link Port 0 (TAB 1): DUAL DVB-S2
[ 4.637879] dvbdev: DVB: registering new adapter (DDBridge)
[ 4.637895] dvbdev: DVB: registering new adapter (DDBridge)
[ 5.090135] ddbridge 0000:01:00.0: DVB: registering adapter 0 frontend 0 (STV090x Multistandard)...
[ 5.165796] ddbridge 0000:01:00.0: DVB: registering adapter 1 frontend 0 (STV090x Multistandard)...
lspci -vvv
Code
01:00.0 Multimedia controller: Digital Devices GmbH Octopus DVB Adapter
Subsystem: Digital Devices GmbH Cine S2 V6.5 DVB adapter
Device tree node: /sys/firmware/devicetree/base/scb/pcie@7d500000/pci@1,0/usb@1,0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 82
Region 0: Memory at 600000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable+ Count=1/2 Maskable- 64bit+
Address: 00000000fffffffc Data: 6540
Capabilities: [90] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Exit Latency L0s unlimited
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range A, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Vendor Specific Information: ID=0000 Rev=0 Len=00c <?>
Kernel driver in use: ddbridge
Kernel modules: ddbridge
Alles anzeigen
vielleicht jemand eine Idee?
PS: Dmesg ist voll davon: