DVB mit Kernlel 2.6

Soulreaver · 14. Januar 2006

Hallo ihr lieben,

ich binn zwar schon einige Zeit VDR User, aber der Kernel 2.6 macht mir seh schwer zu schaffen.

Ich bin dabei meinen VDR von SuSE 9.0 auf Debian Etch umzustellen, und komme einfach nicht weiter.
Ich habe den VDR ohne PRobleme übersetzen können sobald ich ihn aber laden möchte bekomme ich in der messages

Code

Jan 14 17:26:28 schirmuli01 vdr[6650]: no DVB device found

ich dachte der treiber wird im 2.6er automatisch geladen!??

ich hab schon im wiki gestöbert und da finde ich auch immer nur den hinweis dass der Treiber im 2.6er schon vorhanden ist oder ich einen zusätzlich installieren kann!?

Mein Kernel ist 2.6.12-1-386 und als Karten setze ich 3x Hauppauge Nexus-s ein, kann mir jemand klip und klar sagen was ich installieren/laden muss damit der kram funktioniert?

vielen dank im Vorraus
Thilo

pcfanac · 14. Januar 2006

Kennst du denn den Namen von dem Modul(en) die deine Nexus braucht?
Wenn ja versuch sie doch mal mit "modprobe Modulname" zu laden.

Wenn das klappt ist zumindest der Kernel richtig konfiguriert. Dann musst du dann Debian Experten fragen, wo man Module einträgt die automatisch geladen werden sollen.

Bei mir ist das unter /etc/modules.autoload.d/kernel-2.6

Gruss

Soulreaver · 14. Januar 2006

Danke für die Antwort!

Leider bringt sie mich kein stück weiter, woe das Modul bei Booten geladen wird ist mir bekannt leider habe ich keine Ahnung welches modul ich benötige......

Hat jemand anderes noch Infos??

Gruß

wilderigel · 14. Januar 2006

Steht im englischen Wiki unter Developer.
http://www.linuxtv.org/wiki/in…DVB_cards#DVB-S_ff_rev2.1

Firmware ist aufn PC?

Soulreaver · 14. Januar 2006

wilderigel
jaja, die Firmware......

Sag mal gennst du das Gefühl wenn man jemanden spontan KNUTSCHEN könnte?

drichie · 14. Januar 2006

Hi!

Ich habe genau das gleiche Problem...
Jetzt helft mir bitte was gibts das genau für ein "Problem" mit der Firmware auf PC? Wie ist das gemeint? Blicks gerade nicht!

Danke für die Hilfe

Grüße

drichie

wilderigel · 14. Januar 2006

Die Frage ist, ob die Firmware für die DVB-Karte im System an der richtigen Stelle liegt.

Siehe auch http://www.vdr-wiki.de/wiki/index.php/Firmware

drichie · 14. Januar 2006

Danke! Die Antwort kam fix!

die Firmware scheint bei mir nicht das Problem zu sein.

Ich such mal weiter...

Danke

Soulreaver · 15. Januar 2006

Du must die FW an Ort und Stelle kopieren, dann via rmmod dvb_ttpci und modprobe dvb_ttpci das Modul entladen/laden sonst bleibt der Effekt aus...

Viel Glück!!
Thilo

rudirabbit · 17. Januar 2006

Hi !

Mache gerade das selbe wie Soulreaver von Suse9.0 -->Suse10.0

Will erst mal DVB Treiber aus dem Paket DVB nutzen.
Meine Version : vdr 1.3.38
Dieser startet nicht richtig und macht immer einen restart.
Aus dem Logfile geht nicht hervor warum.

wenn ich dmesg mache kommt dies:

Code

Linux version 2.6.13-15-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Sep 13 14:56:15 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
 BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
 BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
 BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 61424 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI                                   ) @ 0x000faae0
ACPI: RSDT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff0000
ACPI: FADT (v001 AMIINT SiS740XX 0x00000011 MSFT 0x0100000b) @ 0x0fff0030
ACPI: MADT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff00c0
ACPI: DSDT (v001    SiS      748 0x00000100 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: local apic disabled
Allocating PCI resources starting at 10000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: root=/dev/hda2 vga=0x317 selinux=0    resume=/dev/hda1  splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1800.250 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 253904k/262080k available (2028k kernel code, 7568k reserved, 700k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3602.74 BogoMIPS (lpj=7205488)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) XP 2200+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1750k freed
ACPI: Looking for DSDT in initrd... not found!
 not found!
ACPI: setting ELCR to 0200 (from 0c28)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to [EMAIL]netdev@vger.kernel.org[/EMAIL] cc [EMAIL]hadi@cyberus.ca[/EMAIL])
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: cdd00000-cfefffff
  PREFETCH window: c9a00000-cdbfffff
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1137433552.512:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xca000000, mapped to 0xd0880000, using 6144k, total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:030f
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 76011 bytes,<6>...found (1024x768, 12703 bytes, v3).
Console: switching to colour frame buffer device 127x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices: 
PCI0 PS2M PS2K UAR1 USB1 USB2 USB3 EHCI  LAN  MDM 
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 204k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
SIS5513: IDE controller at PCI slot 0000:00:02.5
    ACPI-0212: *** Warning: Device is not power manageable
SIS5513: chipset revision 1
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: TOSHIBA MK8025GAS, ATA DISK drive
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB), CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3
Probing IDE interface ide1...
hdc: LG DVD-ROM DRD-8160B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
libata version 1.12 loaded.
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ata1: SATA max UDMA/133 cmd 0xDC00 ctl 0xD802 bmdma 0xCC00 irq 5
ata2: SATA max UDMA/133 cmd 0xD400 ctl 0xD002 bmdma 0xCC08 irq 5
hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata1: no device found (phy stat 00000000)
scsi0 : sata_sis
ata2: no device found (phy stat 00000000)
scsi1 : sata_sis
ACPI: CPU0 (power states: C1[C1])
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
bootsplash: status on console 0 changed to on
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 795176k swap on /dev/hda1.  Priority:-1 extents:1
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL]dm-devel@redhat.com[/EMAIL]
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 746 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 5, io mem 0xcfff8000
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 5, io mem 0xcfff9000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:03.2[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.2: irq 11, io mem 0xcfffa000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
sis900.c: v1.08.08 Jan. 22 2005
intel8x0_measure_ac97_clock: measured 54866 usecs
intel8x0: clocking to 48000
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xbc00, IRQ 5, 00:0b:6a:3b:af:72.
    ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:03.3[D] -> Link [LNKH] -> GSI 3 (level, low) -> IRQ 3
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:03.3: irq 3, io mem 0xcfffb000
PCI: cache line size of 64 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 8 ports detected
Linux video capture interface: v1.00
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
saa7146: found saa7146 @ mem d136ce00 (revision 1, irq 5) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X).
adapter has MAC addr = 00:d0:5c:20:7c:21
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80002622
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: Crystal audio DAC @ card 0 detected
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
DVB: registering frontend 0 (ST STV0299 DVB-S)...
dvb-ttpci: found av7110-0.
bootsplash: status on console 0 changed to on
bcm3510: module not supported by Novell, setting U taint flag.
lgdt330x: module not supported by Novell, setting U taint flag.
or51132: module not supported by Novell, setting U taint flag.
or51211: module not supported by Novell, setting U taint flag.
s5h1420: module not supported by Novell, setting U taint flag.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 not a capable Intel processor
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
eth0: Media Link On 100mbps full-duplex 
powernow-k8: Processor cpuid 6a0 not supported
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
bootsplash: status on console 0 changed to on
subfs 0.9
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
eth0: no IPv6 routers present
eth0: Media Link Off
saa7146: unregister extension 'dvb'.
ACPI: PCI interrupt for device 0000:00:0d.0 disabled
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
saa7146: found saa7146 @ mem d136ee00 (revision 1, irq 5) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X).
adapter has MAC addr = 00:d0:5c:20:7c:21
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80002622
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: Crystal audio DAC @ card 0 detected
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
DVB: registering frontend 0 (ST STV0299 DVB-S)...
dvb-ttpci: found av7110-0.
bcm3510: module not supported by Novell, setting U taint flag.
lgdt330x: module not supported by Novell, setting U taint flag.
eth0: Media Link On 100mbps full-duplex 
or51132: module not supported by Novell, setting U taint flag.
or51211: module not supported by Novell, setting U taint flag.
s5h1420: module not supported by Novell, setting U taint flag.
saa7146: unregister extension 'dvb'.
ACPI: PCI interrupt for device 0000:00:0d.0 disabled
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
saa7146: found saa7146 @ mem d136ee00 (revision 1, irq 5) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X).
adapter has MAC addr = 00:d0:5c:20:7c:21
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80002622
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: Crystal audio DAC @ card 0 detected
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
DVB: registering frontend 0 (ST STV0299 DVB-S)...
dvb-ttpci: found av7110-0.
bcm3510: module not supported by Novell, setting U taint flag.
lgdt330x: module not supported by Novell, setting U taint flag.
or51132: module not supported by Novell, setting U taint flag.
or51211: module not supported by Novell, setting U taint flag.
s5h1420: module not supported by Novell, setting U taint flag.
eth0: Media Link Off
eth0: Media Link On 100mbps full-duplex 
eth0: Media Link Off

Alles anzeigen

Am Ende die bcm3510: module not supported by Novell, setting U taint flag macht mich stutzig

Mit Yast kann ich die DVB Karte konfigurieren, muss ich ne besondere Einstellung machen ?

Gruß !

mauerspecht · 18. Januar 2006

Ich glaube nicht das der bcm3510 Treiber benutzt wird. Es wird einiges an für diese Hardware unnützes Zeug geladen, z.B. auch APM, Microcode.

Interessanter wäre aber der Auszug aus /var/log/messages zu dem Restart.

DVB mit Kernlel 2.6

Jetzt mitmachen!

Teilen