[gelöst:] WLAN USB Stick will nicht

Homer Simpson · 17. Januar 2009

Hallo zusammen,

ich krieg einen Netgear USB WG111v2 nicht zum fliegen.
Ich habe Debian Etch 2.6.18-6-486. Ich habe ndiswrapper als Modul dazugeladen. Hier etwas Info:

Code

cookie2:~# lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 002: ID 0846:6a00 NetGear, Inc. WG111 WiFi (v2)
Bus 001 Device 001: ID 0000:0000

und

Code

cookie2:~# cat /etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
ap_scan=1
network={
    ssid="Homer_Simpson_Net"
    scan_ssid=1
    key_mgmt=NONE
    wep_key0=0123456ABCDEF0123456  <-- Hier steht mein Hex-Key
    wep_tx_keyidx=0
    priority=5
}

Alles anzeigen

ndiswrapper meint:

Code

cookie2:~# wpa_supplicant -Dndiswrapper -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'ndiswrapper' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ap_scan=1
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
scan_ssid=1 (0x1)
key_mgmt: 0x4
wep_key0 - hexdump(len=13): [REMOVED]
wep_tx_keyidx=0 (0x0)
priority=5 (0x5)
Priority group 5
   id=0 ssid='Homer_Simpson_Net'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:18:4d:b1:6f:5a
Driver does not support WPA.
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 532 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 5
0: 00:1d:19:83:ec:09 ssid='WLAN-83EC64' wpa_ie_len=28 rsn_ie_len=26 caps=0x11
   skip - SSID mismatch
1: 00:1f:3f:13:2c:c9 ssid='Homer_Simpson_Net' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
   skip - no WPA/RSN IE
No suitable AP found.

Alles anzeigen

Und mit wext:

Code

cookie2:~# wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ap_scan=1
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
scan_ssid=1 (0x1)
key_mgmt: 0x4
wep_key0 - hexdump(len=13): [REMOVED]
wep_tx_keyidx=0 (0x0)
priority=5 (0x5)
Priority group 5
   id=0 ssid='Homer_Simpson_Net'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:18:4d:b1:6f:5a
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 532 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 5
0: 00:1d:19:83:ec:09 ssid='WLAN-83EC64' wpa_ie_len=28 rsn_ie_len=26 caps=0x11
   skip - SSID mismatch
1: 00:1f:3f:13:2c:c9 ssid='Homer_Simpson_Net' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
   skip - no WPA/RSN IE
No suitable AP found.

Alles anzeigen

In /var/log/messages finde ich:

Code

Jan 17 18:15:32 cookie2 kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jan 17 18:15:47 cookie2 kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready

Hat jemand eine Idee?

Vielen Dank im voraus
Homer.

peje · 17. Januar 2009

was geschieht wenn du ndiswrapper ent- und nachher wieder lädst also in etwa:
rmmod ndiswrapper modprobe ndiswrapper und im syslog oder bei dmesg guckst?

Homer Simpson · 17. Januar 2009

Dann passiert das:

Code

Jan 17 18:58:47 cookie2 kernel: ndiswrapper: device wlan0 removed
Jan 17 18:59:00 cookie2 kernel: ndiswrapper version 1.28 loaded (preempt=no,smp=no)
Jan 17 18:59:01 cookie2 kernel: usb 1-1: reset high speed USB device using ehci_hcd and address 2
Jan 17 18:59:01 cookie2 kernel: ndiswrapper: driver net111v2 (NETGEAR Inc.,03/27/2006,5.1213.06.0327) loaded
Jan 17 18:59:04 cookie2 kernel: wlan0: vendor: 'Realtek RTL8187 Wireless LAN USB NIC                                     '
Jan 17 18:59:04 cookie2 kernel: wlan0: ethernet device 00:18:4d:b1:6f:5a using NDIS driver net111v2, 0846:6A00.F.conf
Jan 17 18:59:04 cookie2 kernel: wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
Jan 17 18:59:04 cookie2 kernel: usbcore: registered new driver ndiswrapper

Und dann:

Code

cookie2:~# wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ap_scan=1
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
scan_ssid=1 (0x1)
key_mgmt: 0x4
wep_key0 - hexdump(len=13): [REMOVED]
wep_tx_keyidx=0 (0x0)
priority=5 (0x5)
Priority group 5
   id=0 ssid='Homer_Simpson_Net'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:18:4d:b1:6f:5a
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 532 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 5
0: 00:1d:19:83:ec:09 ssid='WLAN-83EC64' wpa_ie_len=28 rsn_ie_len=26 caps=0x11
   skip - SSID mismatch
1: 00:1f:3f:13:2c:c9 ssid='Homer_Simpson_Net' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
   selected non-WPA AP 00:1f:3f:13:2c:c9 ssid='Homer_Simpson_Net'
Trying to associate with 00:1f:3f:13:2c:c9 (SSID='Homer_Simpson_Net' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
wpa_driver_wext_set_key: alg=1 key_idx=0 set_tx=1 seq_len=0 key_len=13
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=ForceAuthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=26

Alles anzeigen

Im syslog steht dann:

Code

ADDRCONF(NETDEV_UP): wlan0: link is not ready

Homer Simpson · 17. Januar 2009

Hallo zusammen,

ich hab jetzt mal ndiswrapper Version 1.53 installiert und verwende den WIN98 Netgear Treiber 1.0.3.
Ich kann scannen, aber nicht connecten:

Code

wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ap_scan=1
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
scan_ssid=1 (0x1)
key_mgmt: 0x4
wep_key0 - hexdump(len=13): [REMOVED]
wep_tx_keyidx=0 (0x0)
priority=5 (0x5)
Priority group 5
   id=0 ssid='Homer_Simpson_Net'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:18:4d:b1:6f:5a
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=17):
     48 6f 6d 65 72 5f 53 69 6d 70 73 6f 6e 5f 4e 65   Homer_Simpson_Ne
     74                                                t
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 532 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 5
0: 00:1d:19:83:ec:09 ssid='WLAN-83EC64' wpa_ie_len=28 rsn_ie_len=26 caps=0x11
   skip - SSID mismatch
1: 00:1f:3f:13:2c:c9 ssid='Homer_Simpson_Net' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
   selected non-WPA AP 00:1f:3f:13:2c:c9 ssid='Homer_Simpson_Net'
Trying to associate with 00:1f:3f:13:2c:c9 (SSID='Homer_Simpson_Net' freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: clearing AP WPA IE
WPA: clearing AP RSN IE
WPA: clearing own WPA/RSN IE
No keys have been configured - skip key clearing
wpa_driver_wext_set_key: alg=1 key_idx=0 set_tx=1 seq_len=0 key_len=13
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - portControl=ForceAuthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b1a len=26

Alles anzeigen

Hat jemand eine Idee?

Danke im voraus
Homer.

tr500 · 17. Januar 2009

Zitat

Scan results: 2
Selecting BSS from priority group 5
0: 00:1d:19:83:ec:09 ssid='WLAN-83EC64' wpa_ie_len=28 rsn_ie_len=26 caps=0x11
skip - SSID mismatch
1: 00:1f:3f:13:2c:c9 ssid='Homer_Simpson_Net' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
skip - no WPA/RSN IE
No suitable AP found.

Alles anzeigen

Scheint so als ob der AP das Problem is.Teste es doch mal ohne den WEP/WPA Krempel und verstecke die SSID nicht wenn geschehen.

Hatte selber mit hidden SSID öfter Probleme

Homer Simpson · 17. Januar 2009

SSID wird nicht versteckt.
Ich hab mal das Funknetz ohne WEP/WPA offen wie ein Scheunentor gemacht und die wpa_supplicant.conf wie folgt:

Code

cookie2:~# cat /etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
ap_scan=1
network={
    ssid="Homer_Simpson_Net"
    scan_ssid=1
    key_mgmt=NONE
}

Hilft alles nix - ich krieg diesselben Fehlermeldungen.

Code

skip - no WPA/RSN IE
No suitable AP found.

Und in den messages ADDRCONF(NETDEV_UP): wlan0: link is not ready

Hat jemand eine Idee - einen Vorschlag?
Der Netgear USB WG111v2 ist doch nichts so exotisches. Haben doch sicher viele laufen unter Debian.

Danke
Homer.

Homer Simpson · 18. Januar 2009

Hallo zusammen,

Netgear hat im USB-Stick WG111v2 zweierlei Chipsätze verbaut: Realtek RTL-8187L / Intersil-Conexant GW3887. Welchen man in seinem USB-Stick hat, erkennt man an der FCC ID (an der Seite des Sticks) oder am output von lsusb:
* USB ID: 0846:6a00 is Realtek RTL-8187L chipset
* USB ID: 0846:4240 is Intersil/Conexant GW3887 chipset

Fürr GW3887 verwendet man den p54usb Treiber (Intersil Prisma54). Den gibt's hier:
http://wireless.kernel.org/en/users/Drivers/p54
Doku usw dazu gibt's hier:
http://wireless.kernel.org/en/users/Devices/USB
Hier findet man jede Menge USB Sticks verschiedenster Hersteller und Chipsätze. Netgear, D-Link, Zyxel, Belkin, usw usw usw

Ich hab in meinem Stick den Realtek Chipsatz und brauche daher den Realtek Treiber. Gibt's hier:
http://www.treiberupdate.de/tr…tek-RTL8187LWLANChip.html

Inklusive schöner Anleitung im README.TXT.

Also hab ich das ndiswrapper-Gelumpe wieder entfernt und den Realtek-Treiber verwendet. Mit wpa_supplicant den WEP-Key übergeben und auf Anhieb hat das funktioniert!

Vielleicht kann das mal jemand brauchen...

Hier noch eine gute (und vor allem aktuelle) Seite
http://backtrack.offensive-sec…ex.php?title=HCL:Wireless

Grüße
Homer.

[gelöst:] WLAN USB Stick will nicht

Jetzt mitmachen!

Teilen

Benutzer online in diesem Thema