hallo
hab mir als zweit karte die tt s1400 budget (ich glaub das ist die genaue bezeichnung, aber nicht steinigen wenns nicht stimmt) gekauft
ich dachte dass alle tt-karten unterstützt werden
jedoch erkennt mein vdr (ctvdr 3.06) die karte nicht
ich hab bei der installation zwar den neueren treiber ausgewählt aber gibts vielleicht ein neueren der die karte unterstützt
oder hat jemand die karte vielleicht schon am laufen
falls man da noch dran arbeiten muss würd ich mich schon kümmern wenn mir einer sagt was zu tun ist
achja damits keine verwechslung gibt
ist die kleine in der mitte
http://www.technotrend.de/engl…oducts/pcproducts3-2.html
tt s1400 budget
- rancid-camel
- Geschlossen
-
-
Hallo rancid-camel,
wo hast du diese Karte den her, die sollte es eigendlich noch gar nicht zu kaufen geben?
MfG
Atti -
die karte hab ich von eMüll
hab grad noch mal nachgesehen
ist wohl doch nicht die auf dem bild
schaut zwar ähnlich aus is aber nicht die gleichehier die beschreibung:
ZitatTechnical Specification TT-budget S-1400
TechnoTrend AG © 2004 Page 1 of 2
modeI TT-budget S-1400
TT-PCline DVB family
The best value, the right features all in a PCI card
The model TT-budget S-1400 represents reception
device for basic applications. It features a complete DVB
satellite receiver to receive data broadcasts, digital TV as well
as radio programs and provides high-speed internet access.
The TT-budget S-1400, was especially designed to meet the
demands of the mass market end consumer for easy of
operation and plug & play installation and is a way to access
the internet at DVB?-compliant high-speed at the best value
available.
The incoming DVB? transport stream is delivered to the PCI
bus at a speed of up to 52 Mbps. An optimised software filter
driver manages data processing downstream by filtering up to
255 PIDs concurrently. A MPEG-2 software decoder and
TV/Radio application are included for reception of digital TV
and radio broadcasts. More than one budget card can be
installed in one PC to receive various channels simultaneously.
An easy-to-use multilingual data management utility is
provided to adjust channel and filter settings and to monitor
incoming data. For third-party software developers an open
API (application programming interface) is available.
Technical SpecificationsFunctionality
• QPSK DVB satellite receiver accordingly to ETS 300 421• Low-cost PCI card for digital TV and data application
• Plug & play installation
• Video/Audio decoding by software (application)
• Recording and play back of TV/Radio services
• Multi language support
• Time shift support
• Teletext decoding by software
• Multicast Management support by NDIS driver
Technical Specification TT-budget S-1400
TechnoTrend AG © 2004 Page 2 of 2
Basic Specification
• Symbol rate: 1… 45 Msymbols/s (SCPC & MCPC)
• Automatic FEC selection (1/2, 2/3, 3/4, 5/6, 7/8)
• Automatic LNB voltage selection
• MPEG2 Transport Stream support: ISO/IEC 13818-1
• DVB-Video/-Audio support: ISO/IEC 13818-2, -3
• DVB-Data: ETSI EN 301 192
o MPE
o Data Piping
o Data Streaming
o Data Carousels optional
o Object Carousels optional
RF Input/Output
• Frequency range 950…2150 MHz (L-Band)
• Input connector: IEC F-type female
• Input Impedance 75 ?
• LNB control:
*
Band selection: 22KHz,
*
Polarity: 14/18V,
*
Tone burst mode,
*
DiSEqC 1.1
*
max. current 400mA
Performance• Raw data transfer: PCI Busmaster DMA
• Max. unfiltered data stream: 90 Mbit/s
• Max. download MPEG-2 PES speed: 72 Mbit/s
• Max. download speed for Unicast (TCP/IP): 72 Mbit/s
• Max. download speed for Multicast (IP): 72 Mbit/s
• Maximum 255 PID filters
Minimum PC requirements• Pentium III 733 MHz
• 256 Mbytes RAM
• DirectX 8 or higher
• Graphic card with 800 x 600 x 16 bpp or better
• Sound card
• CD-Rom (Driver and Software installation)
• PCI port (PCI 2.2 compatible)
• Supported Operating System: Windows 98SE, ME, 2000, XP
hier noch ein bild:
-
hat keiner ein tip für mich bezüglich dieser karte?
unter windows läuft die mit den technotrend budget treiber und software ohne probleme
wenns möglich ist linuxtreiber zu entwickeln wär ich dabei (kann zwar noch nicht programmieren aber das könnte ich ja evtl lernen)
diese karten werden wohl auch für skydsl benutzt (gehen bei ebay um die 20€ weg)
schönen abend noch
rancid-camel -
Ich hab mir so nen Teil aus der von dir genannten Quelle geholt, die stammt auch aus einem SkyDSL Paket wie's scheint.
Hab sie für unter 20 EUR bekommen. Leider ist sie noch nicht angekommen,
deshalb konnte ich noch nicht testen. Aber wies scheint wird sie eh noch nicht
unterstützt, wenn der folgende Thread noch aktuell ist:http://www.vdr-portal.de/board/thread.php?threadid=24583
Ist übrigens auch schon im Wiki eingetragen:
http://www.vdr-wiki.de/wiki/index.php/Bild:Nova-S-SE.jpg
btw, wo hast du eigentlich die Beschreibung für die Karte her?
Gruss
derschorsch
-
Was sagt "lspci -vn"? über die Karte?
Was für ein Tuner ist da drauf?
CU
Oliver -
Ich hab auf die schnelle in der linuxtv linux-dvb mailinglist folgenden Thread gefunden.
Ich vermute, dass es sich dabei um die Karte handelt, weil er von einer "NOVA-S SE low profile card" spricht:ZitatI have been playing with my NOVA-S SE low profile card a lot, but now i am
stuck. I hope at least to give somebody some additional input.My findings so far are:
- The budget (not budget-ci) driver matches the saa7146 part quite well if the
appropriate PCI ID is added.
- After opening the top of the tuner box, the PCB matched the picture earlier
in a thread concerning PCI ID 1016 and the datecode is only 1 day later.
- Looking up the two possible demodulation chips mentioned in that thread, i
now am very sure that the two chips are identical or at least register
compatible (the P1010 was developed (for|with) samsung).
- The sh1420 datasheet tells me that all reset values are OK so there is no
setup table needed.
- The driver detects the i2c serial eeprom at i2c device 0x50 and can read the
MAC address.
- I could change the PCI ID of the card by writing to i2c device 0x50 and
address 0 (and back)
- I determined that the saa7146 GPIO 2 is equipped with a pull down (600 ohm
measured) and is routed into the frontend box. The I2C traces go parallel to
the serial eeprom and the tuner box.
- I have a good chance to get 18 Volt output at the F connector by simply
setting the GPIO 2 to OUTHI.
- The chance is about 100% if I try to read from all possible i2c devices
afterwards. This is weird also.
- According to the sh1420 data sheets the device can have i2c id 0xa0,0xa2,
0xa4 or 0xa6 which translates to linux i2c addresses 0x50 to 0x53 if i did
not get it all wrong.
- I am 80% sure that the GPIO is the inverted reset input of the sh1420
- BUT the sh1420 should output 13V according to the default reset values.
- running the saa7146 dump on my brothers XP machine could not list the saa
registers, possibly because i specified 0x50 as i2c device the first time
around and did not log the output. (serial eeprom might be overwritten??) I
have not yet tried to plug it back into my machine, it even might be unusable
now. On the XP machine the output is a bit above 19 Volt.Weird things:
- The serial EEPROM and the sh1420 seem to be at the same i2c device address
by default! (both 0xa0 and following)
- when scanning all possible 256 device addresses of the i2c bus i see that
the upper 128 device addresses mirror the result from the lower addresses.
This and the fact that the serial eeprom datasheet say the device is at 0xa0
and is detected at 0x50 tells me that the device address for linux is shifted
one bit down.
- scanning address 0 gives a rc code of -5 (should be a device broadcast
address?)
- scanning (linux) i2c address 8 gives very strange results:
when reading back single bytes, the return is always the address with the two
lowest bits set to 0: (device 8, starting at address 0)
00 00 00 00 04 04 04 04 08 08 08 08
When reading back more bytes at a time: (device 8, starting at address 0)
00 00 00 00 00 00 00 00 00 00 00 00
or whatever start address is given without the lowest two bits. This seems a
bit strange for a serial bus.
The rc of the i2c transfer is always OK (2)
- Apart from that there is NO indication of the presence of the sh1420, all
other addresses result in rc -121Did i miss something here?
Has somebody seen something like that before?Michael
Vielleicht hilft das ja ein bisschen weiter!?Gruss
derschorsch
-
ufo:
Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH: Unknown device 1016
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at dc000000 (32-bit, non-prefetchable) [disabled] [size=512]Class 0480: 1131:7146 (rev 01)
Subsystem: 13c2:1016
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at dc000000 (32-bit, non-prefetchable) [disabled] [size=512]
00: 31 11 46 71 04 00 80 02 01 00 80 04 00 20 00 00
10: 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 c2 13 16 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 0f 26-- randy
-
ah
ich wusste gar nicht dass das die nova s se ist
dass die noch nicht unterstützt wird hatte ich schon gelesen
naja wenigstens weiß ich jetzt dass ich nicht der einzige mit der karte bin
und des mit der untstüzung in linux wird schon werdengruß
rancid-camel -
Zitat
Original von rancid-camel
und des mit der untstüzung in linux wird schon werden
Von allein aber bestimmt nicht.
Wenn das Teil tatsächlich den oben erwähnten Samsung-Tuner hat, gibt's dafür afaik noch keinen Frontend-Treiber.CU
Oliver -
andrew qincey hat wohl paar karten von hauppauge und samsung hat detaillierte
datasheets inkl programmierbeispiele online. also ist denk ich mal eine frage der zeit.trotzdem sollte man keinen support "erwarten"
-- randy
-
Zitat
Original von randy
andrew qincey hat wohl paar karten von hauppauge und samsung hat detaillierte
datasheets inkl programmierbeispiele online. also ist denk ich mal eine frage der zeit.
Na, dann einfach mal abwarten, was Andrew macht.Btw, richtig erfreulich, daß es frei verfügbare Datasheets gibt. Hatte ich mir seinerzeit gleich geholt. Wer weiß, ob es sich Samsung noch anders überlegt.
CU
Oliver -
hi!
hat eigentlich schon jemand die tt s1400 unter LinVDR laufen?`
Will mir nämlich ne 2. Karte in meinen Rechner stecken und die schaut doch ganz ordentlich aus...
Grüsse
Jörgi -
also ich hab schon lang nicht mehr nach den linuxtreiber geschaut
hab grad das gefunden
http://www.kernel.org/hg/linux-2.6/?cmd=changelog;rev=4506
der 5. artikel
bin mir aber grad nicht sicher ob dass die karte is
werds aber mal probieren wenjn ich zeit habe
gruß
rancid-camel -
Hast schon mal ausprobiert?
Ich will mit nämlich unbedingt ne 2. Karte kaufen... und die wäre ja vom Preis und den Abmaßen ok...
Danke und Grüsse
-
wird die karte mittlerweile stabil unterstützt?
bin nämlich auch auf der suche nach einer
billigen 2.Karte -
hallo
wegen zeitmangel bin ich noch nicht dazu gekommen es genau zu testen
wird bei mir wahrscheilich auch noch etwas dauern bis ich dazukomm
gruß
rancid-camel -
Hallo,
habt ihr was neues ?
Ich habe auch diese Karte aber leider noch kein Bild von der im VDR
Gestestet mit LinVDR 2.6.9 2.6.12.2 und 2.6.13, VDR erkennt das 2. Device, im Endeffekt bei jedem Kernel die aktuellsten DVB Treiber und auch bei jeder Kernelversion die selbe Meldung beim Laden vom Budget Treiber:
CodeSep 19 22:33:57 vdr user.warn kernel: saa7146: register extension 'budget dvb'. Sep 19 22:33:57 vdr user.info kernel: ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 11 (level, low) -> IRQ 11 Sep 19 22:33:57 vdr user.warn kernel: found saa7146 @ mem f8b68000 (revision 1, irq 11) (0x13c2,0x1016). Sep 19 22:33:57 vdr user.warn kernel: DVB: registering new adapter (TT-Budget/WinTV-NOVA-S PCI). Sep 19 22:33:57 vdr user.warn kernel: adapter has MAC addr = 00:d0:5c:04:f9:f8 Sep 19 22:33:57 vdr user.warn kernel: DVB: registering frontend 1 (Samsung S5H1420 DVB-S)...
wenn ich eine Aufnahme starte bekommen ich:
CodeSep 19 22:35:30 vdr user.info vdr[1274]: record /video0/@n-tv__/2005-09-19.22.35.10.01.rec Sep 19 22:35:30 vdr user.debug vdr[1274]: creating directory /video0/@n-tv__ Sep 19 22:35:30 vdr user.debug vdr[1274]: creating directory /video0/@n-tv__/2005-09-19.22.35.10.01.rec Sep 19 22:35:34 vdr user.debug vdr[1274]: recording to '/video0/@n-tv__/2005-09-19.22.35.10.01.rec/001.vdr' Sep 19 22:35:39 vdr user.err vdr[1274]: ERROR: device 2 has no lock, can't attach receiver! Sep 19 22:35:39 vdr user.debug vdr[1274]: buffer stats: 0 (0%) used Sep 19 22:35:39 vdr user.err vdr[1274]: ERROR: Keine freie DVB-Karte zum Aufnehmen! Sep 19 22:35:41 vdr user.debug vdr[1274]: max. latency time 15 seconds
irgendwas passt da noch nicht, Femon sagt kein Carrier.
Ich werde Heute mal den Tuner aufmachen und schauen ob wirklich der Samsung drinnen ist, vielleicht ist es ja möglich den Treiber anzupassen.
Hat sonst noch wer eine Idee ?viele Grüße
Andreas -
Hi,
also ich hab die TT1400 auch bestellt, da die TT1500 noch nicht lieferbar ist. Es geht bei mir auch nur um eine 2. Karte bei einem Bekannten und nach dem ersten Fehlschlag mit einer S1102 habe ich noch die Hoffnung, dass es mit der 1400er geht. Wie siehts damit aus... das letzte Post macht mir nicht gerade Hoffnung
-
Hallo,
so ich habe jetzt mal den Tuner abgelötet und unten geöffnet, es ist tatsächlich der Samsung S5H1420 verbaut, vielleicht liegt es ja doch an etwas anderem. Ich werde dann mal weiter testen.
viele Grüße
Andreas
Jetzt mitmachen!
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!