[vdr-plugin-satip] debug rtsp communication for Inverto OEM devices

fnu

Thanks. Tried this but still nothing happens. As discribed with the 0.3.3 there is immediately a tv signal wether encrypted or not. With the 1.0.0 it is random. Rofafor said i have to provide the RTSP communication of both 0.3.3 and 1.0.0. Is there a another way to debug? And where should be the output? In the Syslog?

Regards

Network traffic capture (via tcpdump, tshark, wireshark, ...) of the port 554 will do the trick to get started. The 0.3.3 doesn't have the TRAC command yet, so this is the safest bet. Please, contact me directly (PM or email), when you have some debug information to be shared.

Also, to keep things as simple as possible, please, use only one active satip device (-d1) and grep any satip specific syslog entries in your 1.0.0 setup.

Ahhh ok, i will try it this afternoon. If there is a result i send it to you via PM. Thank you

Regards

rofafor

You have private news. I hope the command was right.

Regards

Just logged, too. Sent you a PM

It looks like the TCP session must be closed during TEARDOWN:

diff --git a/tuner.c b/tuner.c
index e09bdbc..847d0bf 100644
--- a/tuner.c
+++ b/tuner.c
@@ -226,6 +230,8 @@ bool cSatipTuner::Disconnect(void)
   if (!isempty(*streamAddrM) && (streamIdM >= 0)) {
      cString uri = cString::sprintf("rtsp://%s/stream=%d", *streamAddrM, streamIdM);
      rtspM.Teardown(*uri);
+     // some devices requires a teardown for TCP connection also
+     rtspM.Reset();
      streamIdM = -1;
      }

I'll put all the modifications into the GIT repo sometimes next week, when I'm able to compile and test them on my setup too.

Yes the free transmitters can be tuned reliably. Only with the coded ones it still hacks now and again. But I think that is a another subject. Thanks for the work. If there is something to test, let me know .

Regards

I can confirm that the Telestar Digibit is working again with the patch above.

Rolf: thx for your work

Zitat von fnu

zwick der agent & bolzerrr

Any updates on your issues?

My device was and is running fine. I had some log entries that were unclear but TV was working all the time.
I just made it to run on my diskstation NAS and it is lot more stable than USB DVB devices attached because of driver problems.
The NAS ditributes now to clients via streamdev/xvdr and handels recodings.

I have errors on some channels i´d like to debug. I did a fresh compilesince this sending that trac command dosn´t seem to have any impact...

svdrpsend plug satip trac 0x12
220 SVDRP VideoDiskRecorder 2.1.6; Fri Jan  9 18:09:23 2015; UTF-8
900 SATIP tracing mode: 0x0012
221 DiskStation closing connection

svdrpsend plug satip trac
220 SVDRP VideoDiskRecorder 2.1.6; Fri Jan  9 18:12:26 2015; UTF-8
900 SATIP tracing mode: 0x0012
221 DiskStation closing connection

Log when switching to a non working channel always the same if i set trac or not..

SATIP: Detected 1 RTP packet errors [device 0]

No sctive PID´s..

svdrpsend PLUG satip INFO
220 SVDRP VideoDiskRecorder 2.1.6; Fri Jan  9 19:42:27 2015; UTF-8
900-SAT>IP device: 0
900-CardIndex: 1
900-Stream: rtsp://192.168.0.66/?freq=11493&src=1&sr=22000&pol=h&fec=23&mtype=8psk&ro=0.35&msys=dvbs2 [stream=56]
900-Signal: lock=0 strength=0 quality=0
900-Stream bitrate: 0 kB/s
900-Buffer bitrate: 0 kB/s
900-Buffer usage: 0/1024 kB (0.0%)
900-Channel: Das Erste HD;ARD:11493:HC23M5O35P0S1:S19.2E:22000:5101=27:5102=deu@3,5103=mis@3;5106=deu@106:5104;5105=deu:0:10301:1:1019:0
900-Active pids:
900 Active section filters:
221 closing connection