Hi!
Ich habe einen Shuttle XPC SN68SG2.
Momentan läufts mit e-tobis VDR auf Kubuntu 7.04 ohne gröbere Probleme.
Da ich nun aber 6 Wochen an die österr. Grenze muss und der VDR nicht die ganze Zeit eingeschaltet bleiben soll, wollte ich mir nvram-wakeup installieren.
Mit guess-helper habe ich versucht eine Config zu erstellen:
cat /etc/nvram*
################################################
## Mainboard autodetection information:
##
## - Mainboard vendor: "Shuttle Inc"
## - Mainboard type: "FN68S"
## - Mainboard revision: "V10"
## - BIOS vendor: "Phoenix Technologies, LTD"
## - BIOS version: "6.00 PG"
## - BIOS release: "07/16/2007"
addr_stat = 0x4A
shift_stat = 3
addr_day = 0x4C
addr_hour = 0x4D
addr_min = 0x4E
addr_sec = 0x4F
addr_chk_h = 0x6D
addr_chk_l = 0x6E
upper_method = VT82Cxxx
Alles anzeigen
Wenn ich das dann testen will, kommt folgendes:
sudo nvram-wakeup -s $((`date +%s` + 11 * 60)) --directisa
nvram-wakeup: Your mainboard is currently not supported.
nvram-wakeup: Please try determining the addresses and sending the following
nvram-wakeup: information back to the maintainers:
nvram-wakeup: - The addresses you found out (read README.mb)
nvram-wakeup: - Mainboard vendor: Shuttle Inc
nvram-wakeup: - Mainboard type: FN68S
nvram-wakeup: - Mainboard revision: V10
nvram-wakeup: - BIOS vendor: Phoenix Technologies, LTD
nvram-wakeup: - BIOS version: 6.00 PG
nvram-wakeup: - BIOS release: 07/16/2007
Alles anzeigen
Heißt das, dass es keine chance gibt meinen PC mit nvra,-wakeup zu nutzen?
Hier noch ein paar Infos:
ethtool eht0 (Hab ich im Forum wo gelesen...)
sudo ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 19
Transceiver: external
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Link detected: yes
Alles anzeigen
sudo biosinfo:
Following DMI entries found:
- Mainboard vendor: "Shuttle Inc"
- Mainboard type: "FN68S"
- Mainboard revision: "V10"
- BIOS vendor: "Phoenix Technologies, LTD"
- BIOS version: "6.00 PG"
- BIOS release: "07/16/2007"
Heruntergefahren wird der PC immer mit s2ram, was tadellos funktioniert...
Weiters würde ich gerne wissen, ob ich ACPI-Wakeup verwenden kann, wenn NVRAM-Wakeup nicht funktioniert?
Bzw. : Was ist der Unterschied zw. NVRAM-Wakeup und ACPI-Wakeup?
MfG schnere