Hallo!
Seit einigen Tagen versuche ich mit einem vdr TV zu glotzen, doch der will nicht recht und in den Foren kann ich leider auch keine Hifle dazu finden.
Ich habe es bisher mit ctvdr Installationen und kanotix-vdr boots und Installationen versucht.
ob Kernel 2.4.x oder 2.6.x, ob APM und DMA on/off - es hilft einfach nix. Auch keine Installation mit Skript von zulu (upgrades per DSL).
Der TV am Video-Out meiner 1.3 FF zuckt nur in kurzen Abständen - sonst bleibt das Bild schwarz. Bei APM/DMA off im kanotix boot-menü sehe ich am TV das OSD mit diversen Sendernamen und ich kann sogar umschalten - das Bild bleibt trotzdem schwarz.
Auf der Konsole kommen dann ständig ARM crashed Meldungen.
Starte ich das alte Windoof kann ich nach wie vor ganz normal alle Programme sehen, die DVB Karte funktioniert also.
Hat da jemand eine Idee? ich hoffe ich muss nicht bei Windoof bleiben.
dmesg:
entify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found.
ACPI: setting ELCR to 0200 (from 0c20)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4924k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xf0890, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:02: ioport range 0xe800-0xe80f has been reserved
Simple Boot Flag at 0x3a set to 0x1
Machine check exception polling timer started.
Total HugeTLB memory allocated, 0
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Activating ISA DMA hang workarounds.
vesafb: framebuffer at 0xe4000000, mapped to 0xdc880000, using 4096k, total 4096k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:0368
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash: scanning last 2MB of initrd for signature
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...no good signature found.
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:04.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596b (rev 22) IDE UDMA66 controller on pci0000:00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y160P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
hdd: CRD-8400B, ATAPI CD/DVD-ROM drive
hdd: Disabling (U)DMA for CRD-8400B (blacklisted)
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(66)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 >
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X CD-ROM drive, 128kB Cache
3ware Storage Controller device driver for Linux v1.26.02.000.
3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
libata version 1.10 loaded.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 1088.000 MB/sec
raid5: using function: pIII_sse (1088.000 MB/sec)
raid6: int32x1 175 MB/s
raid6: int32x2 214 MB/s
raid6: int32x4 144 MB/s
raid6: int32x8 140 MB/s
raid6: mmxx1 515 MB/s
raid6: mmxx2 644 MB/s
raid6: sse1x1 472 MB/s
raid6: sse1x2 656 MB/s
raid6: using algorithm sse1x2 (656 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
ACPI wakeup devices:
PCI0 UAR1
ACPI: (supports S0 S1 S4 S5)
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 276k freed
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!
hdd: Disabling (U)DMA for CRD-8400B (blacklisted)
Adding 514040k swap on /dev/hda8. Priority:-1 extents:1
NTFS driver 2.1.22 [Flags: R/W MODULE].
NTFS volume version 3.1.
ACPI: Power Button (FF) [PWRF]
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 16 throttling states)
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: Maximum main memory to use for agp memory: 380M
agpgart: AGP aperture is 32M @ 0xe6000000
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xdcdbe000, 00:0b:2b:04:b0:61, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Linux video capture interface: v1.00
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 5 (level, low) -> IRQ 5
saa7146: found saa7146 @ mem dce40000 (revision 1, irq 5) (0x13c2,0x0000).
DVB: registering new adapter (Technotrend/Hauppauge WinTV DVB-S rev1.X).
adapter has MAC addr = 00:d0:5c:00:92:03
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 8000261d
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0 (VLSI VES1x93 DVB-S)...
dvb-ttpci: found av7110-0.
input: PC Speaker
NET: Registered protocol family 17
saa7146: register extension 'budget dvb'.
saa7146: register extension 'budget_ci dvb'.
saa7146: register extension 'budget dvb /w video in'.
usbcore: registered new driver Technotrend/Hauppauge USB-Nova
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 10 (level, low) -> IRQ 10
ts: Compaq touchscreen protocol output
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
dvb-ttpci: ARM crashed @ card 0
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: adac type set to 0 @ card 0
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7174 Tue Mar 22 06:44:39 PST 2005
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
dvb-ttpci: ARM crashed @ card 0
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: adac type set to 0 @ card 0
dvb-ttpci: ARM crashed @ card 0
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: adac type set to 0 @ card 0
dvb-ttpci: ARM crashed @ card 0
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: adac type set to 0 @ card 0
.
die crashes wiederholen sich fortlaufend