Beim Einschalten vom VDR bekomme ich, wenn ich auf einen analogen Channel umschalte erst einmal die Fehlermeldung Transfer Mode kann nicht gestartet werden, wenn ich noch einmal auf den gleichen Kanal schalte, klappt es . Hier der Log dazu : ( es handelt sich um eine PVR350 )
ZitatAlles anzeigen
Apr 3 22:32:08 vdr vdr[478]: switching to channel 35
Apr 3 22:32:08 vdr vdr[478]: analogTV: Switching to channel 0 on device 0
Apr 3 22:32:08 vdr vdr[478]: analogTV: Switching to channel 0 on device 4
Apr 3 22:32:08 vdr vdr[478]: analogTV: Channel: VOX, SID=12060, 238250 MHz, PAL
Apr 3 22:32:08 vdr vdr[478]: analogTV: Video device: /dev/video0
Apr 3 22:32:08 vdr vdr[478]: analogTV: Video source: 4:
Apr 3 22:32:08 vdr vdr[478]: analogTV: NEW videodev=/dev/video0
Apr 3 22:32:08 vdr vdr[478]: analogTV: Detected V4L version 2
Apr 3 22:32:08 vdr vdr[478]: analogTV: Detected capture device Vanilla iTVC15 card
Apr 3 22:32:08 vdr vdr[478]: analogTV: This device does'nt have a tuner!
Apr 3 22:32:08 vdr vdr[478]: analogTV: This device cannot capture!
Apr 3 22:32:08 vdr vdr[478]: analogTV: You selected a Hauppauge PVR-x50 card, but this is'nt a PVR-card!
Apr 3 22:32:08 vdr vdr[478]: analogTV: Fatal error(s) above. analogTV giving up!
Apr 3 22:32:08 vdr vdr[478]: ERROR: Transfer-Mode kann nicht gestartet werden!
Apr 3 22:32:10 vdr vdr[478]: max. latency time 2 seconds
Apr 3 22:32:12 vdr vdr[478]: switching to channel 35
Apr 3 22:32:12 vdr vdr[478]: analogTV: Switching to channel 0 on device 0
Apr 3 22:32:12 vdr vdr[478]: analogTV: Switching to channel 0 on device 4
Apr 3 22:32:12 vdr vdr[478]: analogTV: Channel: VOX, SID=12060, 238250 MHz, PAL
Apr 3 22:32:12 vdr vdr[478]: analogTV: Video device: /dev/video0
Apr 3 22:32:12 vdr vdr[478]: analogTV: Video source: 4:
Apr 3 22:32:12 vdr vdr[478]: analogTV: NEW Frequency=238250 + 0
Apr 3 22:32:12 vdr vdr[478]: analogTV: NEW videonorm=PAL
Apr 3 22:32:12 vdr vdr[478]: analogTV: NEW videosource=4:
Apr 3 22:32:12 vdr vdr[478]: analogTV: NEW picture properties
Apr 3 22:32:12 vdr vdr[478]: analogTV: NEW PVR MPEG-Encoder parameter(s)
Apr 3 22:32:12 vdr vdr[478]: analogTV: PVR Norm=0:PAL
Apr 3 22:32:12 vdr kernel: saa7115[0]: decoder set norm PAL
In die /etc/init.d/vdr habe ich schon eingetragen :
ZitatAlles anzeigen
case "$1" in
start)
getplugins
getcommands
getreccmds
getremotes
# init PVR Card
/usr/bin/test_ioctl -d /dev/video0 -u 0xff -p 4 -f width=720,height=576
Was kann ich noch machen, das die Karte gleich zu Anfang erkannt wird ?
THX