Hallo ich habe Ubuntu 6.06 32-Bit und eine Hauppauge Win-TV PVR 150 MCE.
Jetzt meine Frage läuft die Karte mit euerer Software zusammen? Weil überall habe ich nur was von DVB gelesen und meine ist eine Analoge. Außerdem habe ich ivtv installiert da ich mich damit nicht auskenne hier der Logeintrag:
Code
[17179588.992000] ivtv: ==================== START INIT IVTV ====================
[17179588.992000] ivtv: version 0.4.6 (tagged release) loading
[17179588.992000] ivtv: Linux version: 2.6.15-26-386 preempt 486 gcc-4.0
[17179588.992000] ivtv: In case of problems please include the debug info between
[17179588.992000] ivtv: the START INIT IVTV and END INIT IVTV lines, along with[17179588.992000] ivtv: any module options, when mailing the ivtv-users mailinglist.
[17179589.536000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
[17179589.536000] usbcore: registered new driver usblp
[17179589.536000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[17179589.664000] usbcore: registered new driver snd-usb-audio
[17179589.972000] AC'97 1 does not respond - RESET
[17179589.972000] AC'97 1 access is not valid [0xffffffff], removing mixer.
[17179589.972000] Unable to initialize codec #1
[17179590.016000] Real Time Clock Driver v1.12
[17179590.028000] intel8x0_measure_ac97_clock: measured 55068 usecs
[17179590.028000] intel8x0: clocking to 48000
[17179590.048000] ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)
[17179590.048000] ACPI: PCI Interrupt 0000:04:05.0[A] -> GSI 20 (level, low) -> IRQ 217
[17179590.048000] ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
[17179590.132000] Floppy drive(s): fd0 is 1.44M
[17179590.136000] input: PC Speaker as /class/input/input1
[17179590.144000] parport: PnPBIOS parport detected.
[17179590.144000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[17179590.192000] tveeprom: ivtv version
[17179590.192000] tveeprom: Hauppauge: model = 26559, rev = C260, serial# = 8400430
[17179590.192000] tveeprom: tuner = LG S001D MK3 (idx = 60, type = 38)
[17179590.192000] tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L') PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
[17179590.192000] tveeprom: audio processor = CX25843 (type = 25)
[17179590.192000] tveeprom: decoder processor = CX25843 (type = 1e)
[17179590.192000] ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
[17179590.196000] FDC 0 is a post-1991 82077
[17179590.204000] usbcore: registered new driver hiddev
[17179590.232000] tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
[17179590.232000] ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
[17179590.392000] input: Logitech USB Mouse as /class/input/input2
[17179590.392000] input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:13.1-2
[17179590.400000] cx25840 1-0044: ivtv driver
[17179590.400000] cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
[17179590.436000] hiddev96: USB HID v1.10 Device [aqua computer aquaero 4.00] on usb-0000:00:13.2-2.1
[17179590.436000] usbcore: registered new driver usbhid
[17179590.436000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179592.568000] ts: Compaq touchscreen protocol output
[17179593.068000] uli526x: eth0 NIC Link is Up 100 Mbps Full duplex
[17179594.696000] NET: Registered protocol family 10
[17179594.696000] lo: Disabled Privacy Extensions
[17179594.696000] IPv6 over IPv4 tunneling driver
[17179594.888000] cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
[17179594.952000] ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44]
[17179594.992000] wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
[17179595.000000] ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b]
[17179595.012000] tda9887 1-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
[17179595.012000] ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
[17179595.680000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
[17179595.896000] ivtv0: Encoder revision: 0x02050032
[17179595.896000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
[17179595.896000] ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
[17179595.896000] ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
[17179595.896000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
[17179595.896000] ivtv0: Create encoder radio stream
[17179595.896000] tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c driver #0
[17179596.032000] ivtv0: Initialized WinTV PVR 150, card #0
[17179596.032000] ivtv: ==================== END INIT IVTV ====================Bedeutet das das ivtv einsatzbereit ist und meine TV Karte erkannt hat? Weil mit xawtv bekomme ich keinen Kanal rein.