Debian Jessie und TT 1.6 - Treiberprobleme

  • Hallo,


    ich hatte mich entschlossen, mein uraltes VDR System neu aufzusetzen.


    Allerdings bekomme ich beim Start vom VDR im Syslog:


    runvdr: stopping after fatal fail (INFO: validating live server ip '0.0.0.0'#012vdr: no primary device found - using first device!)


    Ich habe auch unter /dev nichts, was nach der Karte aussieht.
    Die Treiber sollten doch beim Start automatisch geladen werden.


    Sind die entsprechenden Treiber beim Kernel nicht dabei oder was mache ich falsch.


    Danke Euch


    Jogibär

  • Was sagt denn lspci, dmesg und lsmod|grep dvb?


    Falls kein DVB Treiber installiert ist:


    Code
    cd /usr/src
    git clone git://linuxtv.org/media_build.git
    cd media_build
    make download
    make untar
    make menuconfig 
    (Treiber wählen oder einfach nur speichern und beenden)
    make 
    make install


    und neustarten. Ggfs. musst du noch die kernel-header des aktuellen Kernels installieren.

    - Client1: Thermaltake DH 102 mit 7" TouchTFT * Debian Stretch/vdr-2.4.0/graphtft/MainMenuHooks-Patch * Zotac H55-ITX WiFi * Core i3 540 * 4GB RAM ** Zotac GT630 * 1 TB System HDD * 4 GB RAM * Harmony 900 * satip-Plugin

    - Client2: Alfawise H96 Pro Plus * KODI
    - Server: Intel Pentium G3220 * DH87RL * 16GB RAM * 4x4TB 3.5" WD RED + 1x500GB 2.5" * satip-Plugin
    - SAT>IP: Inverto iLNB

  • Hallo,


    das ging ja schnell.


    lspci sagt :02:06.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)


    Wenn ich Dich richtig verstanden habe, sind die Treiber beim Kernel nicht mit dabei, oder ?


    Jogibär

  • Das weiss ich nicht, daher solltest Du ja mal dmesg und lsmod checken. ;)

    - Client1: Thermaltake DH 102 mit 7" TouchTFT * Debian Stretch/vdr-2.4.0/graphtft/MainMenuHooks-Patch * Zotac H55-ITX WiFi * Core i3 540 * 4GB RAM ** Zotac GT630 * 1 TB System HDD * 4 GB RAM * Harmony 900 * satip-Plugin

    - Client2: Alfawise H96 Pro Plus * KODI
    - Server: Intel Pentium G3220 * DH87RL * 16GB RAM * 4x4TB 3.5" WD RED + 1x500GB 2.5" * satip-Plugin
    - SAT>IP: Inverto iLNB

  • OK,


    dmesg:


    10.467881] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input4
    [ 10.467923] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input5
    [ 10.467962] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
    [ 10.467998] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
    [ 10.468056] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
    [ 10.468092] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
    [ 10.468129] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
    [ 10.509065] radeon 0000:01:05.0: No connectors reported connected with modes
    [ 10.509074] [drm] Cannot find any crtc or sizes - going 1024x768
    [ 10.510436] [drm] fb mappable at 0xFA040000
    [ 10.510437] [drm] vram apper at 0xFA000000
    [ 10.510438] [drm] size 786432
    [ 10.510439] [drm] fb depth is 8
    [ 10.510440] [drm] pitch is 1024
    [ 10.510546] fbcon: radeondrmfb (fb0) is primary device
    [ 10.512540] Console: switching to colour frame buffer device 128x48
    [ 10.514039] radeon 0000:01:05.0: fb0: radeondrmfb frame buffer device
    [ 10.514041] radeon 0000:01:05.0: registered panic notifier
    [ 10.524035] [drm] Initialized radeon 2.39.0 20080528 for 0000:01:05.0 on minor 0
    [ 10.524497] snd_hda_intel 0000:01:05.2: irq 41 for MSI/MSI-X
    [ 10.635426] kvm: Nested Virtualization enabled
    [ 10.744263] systemd-journald[161]: Received request to flush runtime journal from PID 1
    [ 10.832826] saa7146: register extension 'av7110'
    [ 10.833025] saa7146: found saa7146 @ mem ffffc90010116000 (revision 1, irq 20) (0x13c2,0x0000)
    [ 10.833076] av7110 0000:02:06.0: firmware: failed to load dvb-ttpci-01.fw (-2)
    [ 10.833116] av7110 0000:02:06.0: Direct firmware load failed with error -2
    [ 10.833118] av7110 0000:02:06.0: Falling back to user helper
    [ 10.848000] powernow_k8: fid 0x12 (2600 MHz), vid 0xe
    [ 10.848032] powernow_k8: fid 0x10 (2400 MHz), vid 0x10
    [ 10.848034] powernow_k8: fid 0xe (2200 MHz), vid 0x12
    [ 10.848036] powernow_k8: fid 0xc (2000 MHz), vid 0x14
    [ 10.848037] powernow_k8: fid 0xa (1800 MHz), vid 0x16
    [ 10.848039] powernow_k8: fid 0x2 (1000 MHz), vid 0x1a
    [ 10.848106] powernow_k8: Found 1 AMD Processor model unknown (2 cpu cores) (version 2.20.00)
    [ 11.052788] r8169 0000:02:0f.0 eth0: link down
    [ 11.052873] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 11.053278] r8169 0000:02:0f.0 eth0: link down
    [ 11.532043] snd_hda_intel 0000:01:05.2: Codec #0 probe error; disabling it...
    [ 12.104707] RPC: Registered named UNIX socket transport module.
    [ 12.104722] RPC: Registered udp transport module.
    [ 12.104725] RPC: Registered tcp transport module.
    [ 12.104729] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 12.133204] FS-Cache: Loaded
    [ 12.154309] FS-Cache: Netfs 'nfs' registered for caching
    [ 12.201432] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    [ 12.264092] floppy0: no floppy controllers found
    [ 12.632082] r8169 0000:02:0f.0 eth0: link up
    [ 12.632096] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [ 16.560040] snd_hda_intel 0000:01:05.2: no AFG or MFG node found
    [ 16.560115] snd_hda_intel 0000:01:05.2: no codecs initialized
    [ 64.283007] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
    [ 64.296207] NFSD: starting 90-second grace period (net ffffffff818b8cc0)



    lsmod:


    dvb_ttpci 104596 0
    saa7146_vv 56661 1 dvb_ttpci
    ttpci_eeprom 12445 1 dvb_ttpci
    saa7146 25390 2 saa7146_vv,dvb_ttpci
    dvb_core 102010 1 dvb_ttpci
    i2c_core 46012 9 drm,i2c_piix4,dvb_ttpci,drm_kms_helper,i2c_algo_bit,v4l2_common,radeon,ttpci_eeprom,videodev



    Guter Tipp.
    Anscheinend fehlt die Firmware.
    Stimmt, dunkel kann ich mich erinnern, daß ich diese irgendwo installieren mußte.



    Gibt es dafür ein Debianpaket oder wo bekomme ich die neuste Version her?


    Danke nochmals
    Jogibär

  • - Client1: Thermaltake DH 102 mit 7" TouchTFT * Debian Stretch/vdr-2.4.0/graphtft/MainMenuHooks-Patch * Zotac H55-ITX WiFi * Core i3 540 * 4GB RAM ** Zotac GT630 * 1 TB System HDD * 4 GB RAM * Harmony 900 * satip-Plugin

    - Client2: Alfawise H96 Pro Plus * KODI
    - Server: Intel Pentium G3220 * DH87RL * 16GB RAM * 4x4TB 3.5" WD RED + 1x500GB 2.5" * satip-Plugin
    - SAT>IP: Inverto iLNB

  • Hallo,


    Danke, der VDR läuft.


    Bloß habe ich kein Bild / Menu am analogen Anschluß der Karte.


    Ich habe was gelesen, daß man ein Ausgabeplugin benötigt:
    Brauche ich das auch für den integrierten Anschluß?



    Jogibär

  • Ich vermute, Du brauchst das Plugin dvbsddevice.

    - Client1: Thermaltake DH 102 mit 7" TouchTFT * Debian Stretch/vdr-2.4.0/graphtft/MainMenuHooks-Patch * Zotac H55-ITX WiFi * Core i3 540 * 4GB RAM ** Zotac GT630 * 1 TB System HDD * 4 GB RAM * Harmony 900 * satip-Plugin

    - Client2: Alfawise H96 Pro Plus * KODI
    - Server: Intel Pentium G3220 * DH87RL * 16GB RAM * 4x4TB 3.5" WD RED + 1x500GB 2.5" * satip-Plugin
    - SAT>IP: Inverto iLNB

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!