Hallo Wissende,
nachdem nun fast alles bei lief habe ich nun noch einen schwarzen Bildschirm auf meinem Monitor.
der Syslog sieht wie folgt aus , kann jemand hieraus einen Fehler erkennen ?
linvdr:~# logread
Mar 2 23:00:08 linvdr syslog.info syslogd started: BusyBox v1.00 (2004.11.01-04:47+0000)
Mar 2 23:00:08 linvdr user.info kernel: 8139too Fast Ethernet driver 0.9.27
Mar 2 23:00:08 linvdr user.warn kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
Mar 2 23:00:08 linvdr user.debug kernel: PCI: setting IRQ 10 as level-triggered
Mar 2 23:00:08 linvdr user.info kernel: GSI 10 (level, low) -> IRQ 10
Mar 2 23:00:08 linvdr user.info kernel: eth0: RealTek RTL8139 at 0xd097e000, 00:a1:b0:a2:df:8f, IRQ 10
Mar 2 23:00:08 linvdr user.debug kernel: eth0: Identified 8139 chip type 'RTL-8139B'
Mar 2 23:00:08 linvdr local0.info udhcpc[1221]: udhcpc (v0.9.9-pre) started
Mar 2 23:00:09 linvdr user.info kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Mar 2 23:00:09 linvdr local0.debug udhcpc[1221]: Sending discover...
Mar 2 23:00:09 linvdr user.info kernel: Linux video capture interface: v2.00
Mar 2 23:00:09 linvdr user.warn kernel: saa7146: register extension 'dvb'.
Mar 2 23:00:09 linvdr user.warn kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
Mar 2 23:00:09 linvdr user.debug kernel: PCI: setting IRQ 5 as level-triggered
Mar 2 23:00:09 linvdr user.info kernel: GSI 5 (level, low) -> IRQ 5
Mar 2 23:00:09 linvdr user.warn kernel: found saa7146 @ mem d0d36000 (revision 1, irq 5) (0x13c2,0x000a).
Mar 2 23:00:09 linvdr user.warn kernel: DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-CA rev1.X).
Mar 2 23:00:09 linvdr user.warn kernel: adapter has MAC addr = 00:d0:5c:04:4a:31
Mar 2 23:00:10 linvdr local0.debug udhcpc[1221]: Sending select for 192.168.178.24...
Mar 2 23:00:10 linvdr local0.info udhcpc[1221]: Lease of 192.168.178.24 obtained, lease time 864000
Mar 2 23:00:10 linvdr user.warn kernel: dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f22623
Mar 2 23:00:10 linvdr user.warn kernel: dvb-ttpci: firmware @ card 0 supports CI link layer interface
Mar 2 23:00:10 linvdr auth.info sshd[1294]: Server listening on 0.0.0.0 port 22.
Mar 2 23:00:10 linvdr daemon.info init: ^MStarting pid 1304, console /dev/tty1: '/sbin/getty'
Mar 2 23:00:10 linvdr daemon.info init: ^MStarting pid 1305, console /dev/tty2: '/sbin/getty'
Mar 2 23:00:10 linvdr daemon.info init: ^MStarting pid 1310, console /dev/tty4: '/sbin/getty'
Mar 2 23:00:10 linvdr daemon.info init: ^MStarting pid 1309, console /dev/tty3: '/sbin/getty'
Mar 2 23:00:11 linvdr user.warn kernel: dvb-ttpci: DVB-C analog module @ card 0 detected, initializing MSP3415
Mar 2 23:00:11 linvdr user.warn kernel: saa7113 not accessible.
Mar 2 23:00:11 linvdr user.warn kernel: saa7146 (0): registered device video0 [v4l2]
Mar 2 23:00:11 linvdr user.warn kernel: saa7146 (0): registered device vbi0 [v4l2]
Mar 2 23:00:11 linvdr user.warn kernel: DVB: registering frontend 0 (ST STV0297 DVB-C)...
Mar 2 23:00:12 linvdr user.info kernel: input: DVB on-card IR receiver as /class/input/input2
Mar 2 23:00:12 linvdr user.info kernel: dvb-ttpci: found av7110-0.
Mar 2 23:00:12 linvdr user.warn kernel: saa7146: register extension 'budget dvb'.
Mar 2 23:00:12 linvdr user.warn kernel: saa7146: register extension 'budget_ci dvb'.
Mar 2 23:00:12 linvdr user.warn kernel: saa7146: register extension 'budget_av'.
Mar 2 23:00:12 linvdr user.info kernel: b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
Mar 2 23:00:12 linvdr user.info kernel: flexcop-pci: will use the HW PID filter.
Mar 2 23:00:12 linvdr user.info kernel: flexcop-pci: card revision 2
Mar 2 23:00:12 linvdr user.warn kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Mar 2 23:00:12 linvdr user.debug kernel: PCI: setting IRQ 11 as level-triggered
Mar 2 23:00:12 linvdr user.info kernel: GSI 11 (level, low) -> IRQ 11
Mar 2 23:00:12 linvdr user.warn kernel: DVB: registering new adapter (FlexCop Digital TV device).
Mar 2 23:00:12 linvdr user.info kernel: b2c2-flexcop: MAC address = 00:d0:d7:0d:e1:97
Mar 2 23:00:12 linvdr user.err kernel: b2c2-flexcop: i2c master_xfer failed
Mar 2 23:00:12 linvdr user.err kernel: b2c2-flexcop: i2c master_xfer failed
Mar 2 23:00:12 linvdr user.info kernel: b2c2-flexcop: found the mt352 at i2c address: 0x0f
Mar 2 23:00:12 linvdr user.warn kernel: DVB: registering frontend 1 (Zarlink MT352 DVB-T)...
Mar 2 23:00:12 linvdr user.info kernel: b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
Mar 2 23:00:12 linvdr user.warn kernel: lirc_dev: IR Remote Control driver registered, at major 61
Mar 2 23:00:12 linvdr user.warn kernel: lirc_serial: no version for "lirc_unregister_plugin" found: kernel tainted.
Mar 2 23:00:13 linvdr user.info kernel: lirc_serial: auto-detected active high receiver
Mar 2 23:00:13 linvdr user.warn kernel: lirc_dev: lirc_register_plugin: sample_rate: 0
Mar 2 23:00:14 linvdr user.info vdr: [1378] VDR version 1.4.4-2-Toxic-Ed. started
Mar 2 23:00:14 linvdr user.info vdr: [1378] Bigpatch 17.09.2006 is active!
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading plugin: /usr/lib/vdr/plugins/libvdr-mplayer.so.1.4.5
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading plugin: /usr/lib/vdr/plugins/libvdr-streamdev-client.so.1.4.5
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading plugin: /usr/lib/vdr/plugins/libvdr-streamdev-server.so.1.4.5
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading plugin: /usr/lib/vdr/plugins/libvdr-streamplayer.so.1.4.5
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading plugin: /usr/lib/vdr/plugins/libvdr-wirbelscan.so.1.4.5
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/setup.conf
Mar 2 23:00:14 linvdr user.err vdr: [1378] ERROR: unknown config parameter: RecordDolbyDigital = 1
Mar 2 23:00:14 linvdr user.err vdr: [1378] ERROR: unknown config parameter: ShowProgressBar = 0
Mar 2 23:00:14 linvdr user.err vdr: [1378] ERROR: unknown config parameter: SortTimers = 1
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/sources.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/diseqc.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/channels.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/timers.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/commands.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/reccmds.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/svdrphosts.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/remote.conf
Mar 2 23:00:14 linvdr user.info vdr: [1378] loading /etc/vdr/keymacros.conf
Mar 2 23:00:14 linvdr user.debug vdr: [1378] reading EPG data from /video0/epg.data
Mar 2 23:00:14 linvdr user.debug vdr: [1385] video directory scanner thread started (pid=1385, tid=1385)
Mar 2 23:00:14 linvdr user.debug vdr: [1386] video directory scanner thread started (pid=1386, tid=1386)
Mar 2 23:00:14 linvdr user.debug vdr: [1378] probing /dev/dvb/adapter0/frontend0
Mar 2 23:00:14 linvdr user.debug vdr: [1386] video directory scanner thread ended (pid=1386, tid=1386)
Mar 2 23:00:14 linvdr user.debug vdr: [1385] video directory scanner thread ended (pid=1385, tid=1385)
Mar 2 23:00:16 linvdr user.debug vdr: [1388] tuner on device 1 thread started (pid=1388, tid=1388)
Mar 2 23:00:16 linvdr user.debug vdr: [1389] section handler thread started (pid=1389, tid=1389)
Mar 2 23:00:16 linvdr user.debug vdr: [1378] probing /dev/dvb/adapter1/frontend0
Mar 2 23:00:16 linvdr user.debug vdr: [1391] tuner on device 2 thread started (pid=1391, tid=1391)
Mar 2 23:00:16 linvdr user.debug vdr: [1392] section handler thread started (pid=1392, tid=1392)
Mar 2 23:00:16 linvdr user.debug vdr: [1378] probing /dev/dvb/adapter2/frontend0
Mar 2 23:00:16 linvdr user.info vdr: [1378] found 2 video devices
Mar 2 23:00:16 linvdr user.info vdr: [1378] initializing plugin: mplayer (0.9.15): Media replay via MPlayer
Mar 2 23:00:16 linvdr user.info vdr: [1378] loading /etc/vdr/plugins/mplayersources.conf
Mar 2 23:00:16 linvdr user.info vdr: [1378] initializing plugin: streamdev-client (0.3.3-pre3-geni): VTP Streaming Client
Mar 2 23:00:16 linvdr user.info vdr: [1378] initializing plugin: streamdev-server (0.3.3-pre3-geni): VDR Streaming Server
Mar 2 23:00:16 linvdr user.info vdr: [1378] initializing plugin: streamplayer (0.1.2): Stream video player
Mar 2 23:00:16 linvdr user.info vdr: [1378] initializing plugin: wirbelscan (0.0.2): dvb c/t/s/analog scan
Mar 2 23:00:16 linvdr user.info vdr: [1378] setting primary device to 1
Mar 2 23:00:16 linvdr user.info vdr: [1378] SVDRP listening on port 2001
Mar 2 23:00:16 linvdr user.info vdr: [1378] setting current skin to "classic"
Mar 2 23:00:16 linvdr user.info vdr: [1378] loading /etc/vdr/themes/classic-default.theme
Mar 2 23:00:16 linvdr user.info vdr: [1378] starting plugin: mplayer
Mar 2 23:00:16 linvdr user.info vdr: [1378] starting plugin: streamdev-client
Mar 2 23:00:16 linvdr user.debug vdr: [1378] reading EPG data from /video0/epg.data
Mar 2 23:00:16 linvdr user.debug vdr: [1393] streamdev-client: sections assembler thread started (pid=1393, tid=1393)
Mar 2 23:00:16 linvdr user.debug vdr: [1394] section handler thread started (pid=1394, tid=1394)
Mar 2 23:00:16 linvdr user.info vdr: [1378] starting plugin: streamdev-server
Mar 2 23:00:16 linvdr user.info vdr: [1378] loading /etc/vdr/plugins/streamdevhosts.conf
Mar 2 23:00:16 linvdr user.info vdr: [1378] starting plugin: streamplayer
Mar 2 23:00:16 linvdr user.info vdr: [1378] loading /etc/vdr/plugins/streamplayer-bookmarks.conf
Mar 2 23:00:16 linvdr user.debug vdr: [1395] streamdev server thread started (pid=1395, tid=1395)
Mar 2 23:00:16 linvdr user.info vdr: [1395] Streamdev: Listening (VTP) on port 2004
Mar 2 23:00:16 linvdr user.info vdr: [1395] Streamdev: Listening (HTTP) on port 3000
Mar 2 23:00:16 linvdr user.info vdr: [1378] starting plugin: wirbelscan
Mar 2 23:00:16 linvdr user.debug vdr: [1378] remote control LIRC - keys known
Mar 2 23:00:16 linvdr user.debug vdr: [1378] remote control KBD - keys known
Mar 2 23:00:16 linvdr user.info vdr: [1378] switching to channel 22
Mar 2 23:00:16 linvdr user.debug vdr: [1396] LIRC remote control thread started (pid=1396, tid=1396)
Mar 2 23:00:16 linvdr user.debug vdr: [1397] KBD remote control thread started (pid=1397, tid=1397)
Mar 2 23:00:41 linvdr cron.notice crond[1409]: crond 2.3.2 dillon, started, log level 8
Mar 2 23:01:33 linvdr auth.info sshd[1492]: Accepted password for root from 192.168.178.23 port 4968 ssh2
Mar 2 23:01:33 linvdr auth.info sshd[1492]: lastlog_get_entry: Error reading from /var/log/lastlog: Bad file descriptor
Mar 2 23:01:33 linvdr auth.info PAM_unix[1492]: (ssh) session opened for user root by (uid=0)
Mar 2 23:01:33 linvdr auth.err PAM-env[1492]: Unable to open config file: No such file or directory
Mar 2 23:01:33 linvdr auth.err PAM-env[1493]: Unable to open config file: No such file or directory
Mar 2 23:03:25 linvdr user.err vdr: [1378] ERROR: Streamdev: Couldn't connect to 10.30.0.20:2004: Connection timed out
Mar 2 23:03:25 linvdr user.debug vdr: [1378] setting watchdog timer to 900 seconds
Mar 2 23:03:25 linvdr user.debug vdr: [1494] transfer thread started (pid=1494, tid=1494)
Mar 2 23:03:25 linvdr user.debug vdr: [1495] receiver on device 2 thread started (pid=1495, tid=1495)
Mar 2 23:03:25 linvdr user.debug vdr: [1496] TS buffer on device 2 thread started (pid=1496, tid=1496)
Mar 2 23:03:26 linvdr user.debug vdr: [1494] setting audio track to 1 (0)
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing pids of channel 20 from 4401+4401:4402:4404 to 4401+4401:4402=deu:4404
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing id of channel 19 from 0-0-2-0 to 8468-2561-2-0
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing name of channel 19 from 'arte,;' to 'arte,;ARD'
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing id of channel 20 from 0-0-3-0 to 8468-2561-3-0
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing name of channel 20 from 'Phoenix,;' to 'Phoenix,;ARD'
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing id of channel 21 from 0-0-4-0 to 8468-2561-4-0
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing name of channel 21 from 'EinsExtra,;' to 'EinsExtra,;ARD'
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing id of channel 22 from 0-0-128-0 to 8468-2561-128-0
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing name of channel 22 from 'Das Erste,;' to 'Das Erste,;ARD'
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing pids of channel 21 from 4417+4417:4418:0 to 4417+4417:4418=deu:0
Mar 2 23:03:27 linvdr user.debug vdr: [1378] max. latency time 1 seconds
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing pids of channel 22 from 4369+4369:4370:4372 to 4369+4369:4370=deu:4372
Mar 2 23:03:27 linvdr user.debug vdr: [1392] changing pids of channel 19 from 4385+4385:4386,4387:4388 to 4385+4385:4386=deu,4387=fra:4388
Mar 2 23:05:01 linvdr cron.notice crond[1409]: USER root pid 1497 cmd convert.pl -q -s
linvdr:~#