Hi,
since my update yesterday XBMC won´t show anymore. I tried all above but still nothing.
The pre2 came out today so I did a clean install with pre2, however XBMC still does not show. When I give a command #start xbmc repley is: job already running: xbmc.
No xbmc crash log.
Thanks for the howto.
However it still did not work. Finally I found that it was the forcedeth driver that was the problem. So waiting for my new nic, I setup a yavdr in Virtualbox.
Now I can access my netceiver, but I still have no picture. The netceiver is ¨waiting for a free tuner¨. It seems as if the tuner will not tune.
Here the result of netcvdiag -a:
Count: 1
NetCeiver 0:
UUID <fe80::208:54ff:fe55:413c>, ALIVE, tuners 1
OS <2.4.32-uc0>, App <0.99.33>, FW <AVR0033/FPGAA5J>, HW <0055>
Serial <33e60000021ac09d>, Vendor <BayCom GmbH>, state 0
SystemUptime 237776, ProcessUptime 237765
TunerTimeout 3600
CI-Slot 0: State <MISSING>, Mode <CA_SINGLE>, CAPMT-Flag: 0, SIDs 0/0, CAM <>
CI-Slot 1: State <READY>, Mode <CA_MULTI_TRANSPONDER>, CAPMT-Flag: 256, SIDs 0/4, CAM <Aston Module 2.0900>
Tuner 0: <ST STV0299 DVB-S>, SatList: <Multiswitch 1>, Preference 0
NetCeiver 0: SatList <Multiswitch 1>, entries 2
Satname: <S19.2E>, Position <19.2E>, entries 4
Entry 0: Polarisation V, Min 10700, Max 11725, LOF 9750 MINI_A TONE_OFF VOLTAGE_13 DiSEqC <E0 10 38 F0>
Entry 1: Polarisation V, Min 11726, Max 12750, LOF 10600 MINI_A TONE_ON VOLTAGE_13 DiSEqC <E0 10 38 F1>
Entry 2: Polarisation H, Min 10700, Max 11725, LOF 9750 MINI_A TONE_OFF VOLTAGE_18 DiSEqC <E0 10 38 F2>
Entry 3: Polarisation H, Min 11726, Max 12750, LOF 10600 MINI_A TONE_ON VOLTAGE_18 DiSEqC <E0 10 38 F3>
Satname: <S13.0E>, Position <13.0E>, entries 4
Entry 0: Polarisation V, Min 10700, Max 11725, LOF 9750 MINI_B TONE_OFF VOLTAGE_13 DiSEqC <E0 10 38 F4>
Entry 1: Polarisation V, Min 11726, Max 12750, LOF 10600 MINI_B TONE_ON VOLTAGE_13 DiSEqC <E0 10 38 F5>
Entry 2: Polarisation H, Min 10700, Max 11725, LOF 9750 MINI_B TONE_OFF VOLTAGE_18 DiSEqC <E0 10 38 F6>
Entry 3: Polarisation H, Min 11726, Max 12750, LOF 10600 MINI_B TONE_ON VOLTAGE_18 DiSEqC <E0 10 38 F7>
UUID <fe80::208:54ff:fe55:413c>:
slot 0.0, type DVB-S, used: 0
NO LOCK, frequency 0kHz (0.0MHz), position <180.0W>
strength 0000, snr 0000, ber deaddead, unc deaddead
NIMCurrent 0
RotorStatus 0, RotorDiff 0.0
Frequency remains at 0khz and position at 180.0W (iso 19.2E)
Someone any idea what is wrong or has to be changed?
Hey all,
is there, or has anyone an howto to get the netceiver working in yavdr 0.3 using the mcli-plug-in.
After a lot of trial and even more error, I´m still not able to get the netceiver working with vlan and xbmc frontend.
I tried most of the methods described on the forum, however some parts of the plug-in are not always recognized. It seems the plug-in will not fully install.
Please help.
German language is ok.
Thanks.
