Danke an alle, jetzt ist es durchgelaufen
Beiträge von JurKub
-
-
Per "ncdu" schauen ob irgendwo ungewöhnlich viel Platz verbraucht wird. Unnötige Pakete (z.B. nicht mehr benötigte Kernel(quellen)) purgen.
ncdu findet er nicht, wo und wie finde ich denn nicht mehr benötigte Kernel(quellen) ?
Apt cache löschen "sudo apt-get clean". Schauen ob unter /var/log Platz zu machen ist.
hab ich schon gemacht
-
Hi all,
ich hab yaVDR 0.3 auf einer 4GB CF Card installiert und /srv per NFS eingebunden.
Bei einem apt-get dist-upgrade bzw. dpkg -i v4l-dvb-dkms_1~20110324.git235676.160_all.deb läuft mir jetzt die CF Card voll.Bei meinem anderen VDR geht's nach mehrmalingem Anlauf
Wo kann ich aufräumen/löschen um Platz zu schaffen?
cu
JurKub -
yep, das war's
Nachdem ich das v4l-dvb-dkms_1~20110324.git235676.160_all.deb installiert hab geht's wieder
Vielen Dank für Deine Hilfe
JurKub -
Danach ist es in einzelnen Fällen nötig gewesen über das WFE des Ausgabe-Frontend nochmals explizit zu setzen.
Das hat nix geholfen.
Du könntest auch eine etwas neuere Version, aber älter als die in "stable-vdr" ausprobieren:
.deb runterladen und mit
#/> sudo dpkg -i v4l-dvb-dkms_1~20110324.git235676.160_all.deb
installieren.
ok, probiere ich mal aus
-
Was ich jetzt nicht verstehe, wenn alle Pakete aktualisiert sind, nur das "v4l-dvb-dkms" nicht, läuft der VDR dann?
ja, ich kann halt nur kein apt-get dist-upgrade mehr machen sondern muss immer alle Pakete einzeln installieren
-
yep, hatte ich gelesen aber danach bleibt mein Systems halt stehen !
Das Stück für Stück upgrade hab ich gemacht um zu sehen an welchem Paket es liegt.
-
ok, das nächste mal hänge ich das syslog als Datei an
Stück für Stück heißt:
1. apt-get update
2. apt-get upgrade
3. apt-get install vdr yavdr-utils usw. bis nur noch v4l-dvb-dkms übrig istIm obigen apt-cache policy v4l-dvb-dkms ist das neue v4l-dvb-dkms ist noch NICHT installiert.
Ich wollte damit zeigen von welcher zu welcher Version das upgrade läuftDanach habe ich es installiert und dann kommt es zum beschriebenen Problem
-
Hi all,
ich hab mein System jetzt Stück für Stück handisch upgedated.
CodeVDR1# apt-get -s dist-upgrade Paketlisten werden gelesen... Fertig Abhängigkeitsbaum wird aufgebaut Status-Informationen einlesen... Fertig Berechne Upgrade (Paketaktualisierung) ...Fertig Die folgenden Pakete werden aktualisiert: v4l-dvb-dkms 1 aktualisiert, 0 neu installiert, 0 zu entfernen und 0 nicht aktualisiert. Inst v4l-dvb-dkms [0~20101018.15139] (0~20110625.git255868.188~lucid stable-vdr:10.04/lucid) Conf v4l-dvb-dkms (0~20110625.git255868.188~lucid stable-vdr:10.04/lucid)
Es fehlt jetzt nur noch v4l-dvb-dkms. Wenn ich das allerding update bleibt yaVDR bei dem Bildschirm mit dem grünen Power-Logo, also noch vor dem yaVDR-Logo, stehen.
CodeVDR1# apt-cache policy v4l-dvb-dkms v4l-dvb-dkms: Installiert: 0~20101018.15139 Kandidat: 0~20110625.git255868.188~lucid Versions-Tabelle: 0~20110625.git255868.188~lucid 0 500 http://ppa.launchpad.net/yavdr/stable-vdr/ubuntu/ lucid/main Packages *** 0~20101018.15139 0 100 /var/lib/dpkg/status
Hat jemand vielleicht eine Idee?
So sieht das syslog aus:
Schomal vielen Dank für Eure Hilfe
JurKub -
hey es geht
Die licrd.conf hatte tatsächlich eine Macke
Vielen Dank an alle für eure Hilfe
JurKub
-
wie sehe ich denn welche lircd.conf benutzt wird?
ps -ef|grep lircd
Codevdr 1310 1 5 15:59 ? 00:00:35 /usr/bin/vdr --lirc=/var/run/lirc/lircd -v /srv/vdr/video.00 -c /var/lib/vdr -L /usr/lib/vdr/plugins -r /usr/lib/vdr/vdr-recordingaction -s /usr/lib/vdr/vdr-shutdown.wrapper -E /var/cache/vdr/epg.data -u vdr -g /tmp --port 6419 -w 0 -Prestfulapi --port=8002 --ip=0.0.0.0 --epgimages=/var/cache/vdr/epgimages --channellogos=/usr/share/vdr-channellogos -Pdbus2vdr -Pmenuorg -Pmarkad -Ptext2skin -Pextrecmenu -Pfemon -Pconflictcheckonly -Piptv -Pchannellists -Pskinpearlhd --epgimages=/var/cache/vdr/epgimages -Pepgsearchonly -Pwirbelscan -Pepgsearch -f /usr/bin/svdrpsend -Pquickepgsearch -Plive --port=8008 --ip=0.0.0.0 --epgimages=/var/cache/vdr/epgimages -Pstreamdev-server -Pxine -r -Pxvdr -t 10 -Pdynamite root 2196 1 0 16:09 ? 00:00:00 /usr/sbin/eventlircd -f --repeat-filter --socket=/var/run/lirc/lircd root 2207 1 0 16:09 ? 00:00:00 /usr/sbin/lircd --nodaemon --uinput --output=/var/run/lirc/lircd.2207 --device=/dev/lirc0 root 2220 1782 0 16:11 pts/0 00:00:00 grep --color=auto lircd
-
das war es leider auch nicht
Code
Alles anzeigenroot@VDR-Office:~# stop eventlircd eventlircd stop/waiting root@VDR-Office:~# mode2 -d /dev/lirc1 mode2: could not get file information for /dev/lirc1 mode2: default_init(): No such file or directory root@VDR-Office:~# mode2 -d /dev/lirc0 space 16777215 pulse 1823 space 857 pulse 906 space 859 pulse 933 space 1684 pulse 1848 space 831 pulse 906 space 857 pulse 909 space 857 pulse 906 space 1711 pulse 1820 space 857 pulse 906 space 856 pulse 932 space 834 pulse 909 space 90466 pulse 1823 space 854 pulse 909 space 858 pulse 910 space 1709 pulse 1846 space 830 pulse 906 space 858 pulse 907 space 858 pulse 933 space 1684 pulse 1822 space 854 pulse 908 space 858 pulse 931 space 834 pulse 933
-
cat /proc/bus/input/devices
Code
Alles anzeigenI: Bus=0019 Vendor=0000 Product=0001 Version=0000 N: Name="Power Button" P: Phys=PNP0C0C/button/input0 S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 U: Uniq= H: Handlers=kbd event0 B: PROP=0 B: EV=3 B: KEY=10000000000000 0 I: Bus=0019 Vendor=0000 Product=0001 Version=0000 N: Name="Power Button" P: Phys=LNXPWRBN/button/input0 S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 U: Uniq= H: Handlers=kbd event1 B: PROP=0 B: EV=3 B: KEY=10000000000000 0 I: Bus=0011 Vendor=0001 Product=0001 Version=ab41 N: Name="AT Translated Set 2 keyboard" P: Phys=isa0060/serio0/input0 S: Sysfs=/devices/platform/i8042/serio0/input/input2 U: Uniq= H: Handlers=sysrq kbd event2 B: PROP=0 B: EV=120013 B: KEY=402000000 3803078f800d001 feffffdfffefffff fffffffffffffffe B: MSC=10 B: LED=7 I: Bus=0011 Vendor=0002 Product=0001 Version=0000 N: Name="PS/2 Generic Mouse" P: Phys=isa0060/serio1/input0 S: Sysfs=/devices/platform/i8042/serio1/input/input3 U: Uniq= H: Handlers=mouse0 event3 B: PROP=0 B: EV=7 B: KEY=70000 0 0 0 0 B: REL=3 I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="lircd" P: Phys= S: Sysfs=/devices/virtual/input/input4 U: Uniq= H: Handlers=sysrq rfkill kbd event4 B: PROP=0 B: EV=100003 B: KEY=ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff fffffffffffffffe I: Bus=0000 Vendor=0000 Product=0000 Version=0000 N: Name="eventlircd" P: Phys=/dev/input/event4 S: Sysfs=/devices/virtual/input/input5 U: Uniq= H: Handlers=event5 B: PROP=0 B: EV=3 B: KEY=ffffffffff 0 0 0 0 0 3fcff 7fff8fff00ff03ff 0 0 0 0
dmesg | grep lirc
Code[ 15.899874] lirc_dev: IR Remote Control driver registered, major 251 [ 16.900021] lirc_serial: auto-detected active low receiver [ 16.900125] lirc_serial lirc_serial.0: lirc_dev: driver lirc_serial registered at minor = 0 [ 16.938401] input: lircd as /devices/virtual/input/input4 [ 17.100206] input: eventlircd as /devices/virtual/input/input5
status eventlircd
-
bei irw kommt bei mir leider überhaupt nix
-
Hi all,
beim Test mit irw kommt nix und in VDR geht's auch nicht.
Wenn ich im Webfrontend LIRC abschalte geht mode2.Bin für jede Hilfe dankbar, mir fäll nix mehr ein was ich testen könnte
An der remote.conf habe ich nichts geändert.
Anbei meine Configs:hardware.conf
Code
Alles anzeigen################################################################################# # # # The following configuration file is generated automatically by the yaVDR # # system. Don't change this file as every update of yaVDR will overwrite # # the local changes. Instead put your required customizations # # into /etc/yavdr/templates_custom/ based on the original templates # # under /usr/share/yavdr/templates. # # # # http://www.yavdr.org/developer-zone/template-overview/ # # # # # ################################################################################# # /etc/lirc/hardware.conf # #Chosen Remote Control REMOTE="Home-brew (16x50 UART compatible serial port)" REMOTE_MODULES="lirc_dev lirc_serial" REMOTE_DRIVER="" REMOTE_DEVICE="/dev/lirc0" REMOTE_LIRCD_CONF="" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="None" TRANSMITTER_MODULES="" TRANSMITTER_DRIVER="" TRANSMITTER_DEVICE="" TRANSMITTER_LIRCD_CONF="" TRANSMITTER_LIRCD_ARGS="" #Enable lircd START_LIRCD="true" #Don't start lircmd even if there seems to be a good config file #START_LIRCMD="false" #Try to load appropriate kernel modules LOAD_MODULES="true" # Default configuration files for your hardware if any LIRCMD_CONF="" #Forcing noninteractive reconfiguration #If lirc is to be reconfigured by an external application #that doesn't have a debconf frontend available, the noninteractive #frontend can be invoked and set to parse REMOTE and TRANSMITTER #It will then populate all other variables without any user input #If you would like to configure lirc via standard methods, be sure #to leave this set to "false" FORCE_NONINTERACTIVE_RECONFIGURATION="false" START_LIRCMD=""
lircd.conf
Code
Alles anzeigen# Please make this file available to others # by sending it to <lirc@bartelmus.de> # # this config file was automatically generated # using lirc-0.8.7(default) on Thu Oct 13 08:49:02 2011 # # contributed by # # brand: /etc/lirc/lircd.conf # model no. of remote control: # devices being controlled by this remote: # begin remote name /etc/lirc/lircd.conf bits 13 flags RC5|CONST_LENGTH eps 30 aeps 100 one 908 871 zero 908 871 plead 915 gap 116035 min_repeat 2 suppress_repeat 2 # uncomment to suppress unwanted repeats toggle_bit_mask 0x800 begin codes KEY_UP 0x1006 KEY_DOWN 0x1007 KEY_MENU 0x100B KEY_OK 0x100A KEY_ESC 0x100C KEY_LEFT 0x1008 KEY_RIGHT 0x1009 KEY_RED 0x1023 KEY_GREEN 0x1024 KEY_YELLOW 0x1025 KEY_BLUE 0x1026 KEY_0 0x1021 KEY_1 0x1017 KEY_2 0x1018 KEY_3 0x1019 KEY_4 0x101A KEY_5 0x101B KEY_6 0x101C KEY_7 0x101D KEY_8 0x101E KEY_9 0x101F KEY_INFO 0x100E KEY_PLAY 0x1012 KEY_PAUSE 0x1016 KEY_STOP 0x100F KEY_RECORD 0x1013 KEY_FASTFORWARD 0x1015 KEY_REWIND 0x1014 KEY_NEXT 0x1025 KEY_BACK 0x1024 KEY_POWER2 0x103E KEY_CHANNELUP 0x1004 KEY_CHANNELDOWN 0x1003 KEY_PREVIOUS 0x1005 KEY_VOLUMEUP 0x1001 KEY_VOLUMEDOWN 0x1002 KEY_MUTE 0x1780 KEY_SUBTITLE 0x1020 KEY_EPG 0x100D KEY_CHANNEL 0x1022 KEY_FAVORITES 0x1028 KEY_TIME 0x102C KEY_PVR 0x102B KEY_SETUP 0x102D end codes end remote
-
-
ich nochmal
nach einem
lässt sich die Version 0.02 jetzt kopilieren.
Jetzt bekomme ich aber nach einem
folgende Fehlermeldung:
CodeCan't locate HTTP/Request.pm in @INC (@INC contains: /etc/perl /usr/local/lib/perl/5.10.1 /usr/local/share/perl/5.10.1 /usr/lib/perl5 /usr/share/perl5 /usr/lib/perl/5.10 /usr/share/perl/5.10 /usr/local/lib/site_perl .) at shairport.pl line 42. BEGIN failed--compilation aborted at shairport.pl line 42.
und
hab ich schon gemacht
-
Hi Uwe,
ich bekomme folgende Fehlermeldung wenn ich die Version 0.01 kopiliere:
Codegcc hairtunes.c alac.c -D__i386 -lm `pkg-config --cflags --libs ao openssl` -o hairtunes /bin/sh: pkg-config: Kommando nicht gefunden. hairtunes.c: In function âinit_outputâ: hairtunes.c:642: error: âao_sample_formatâ has no member named âmatrixâ make: *** [hairtunes] Fehler 1
wenn ich die Version 0.02 kopiliere bekomme folgende Fehlermeldung:Code
Alles anzeigengcc hairtunes.c alac.c -D__i386 -lm `pkg-config --cflags --libs ao openssl` -o hairtunes /bin/sh: pkg-config: Kommando nicht gefunden. /tmp/ccoaOSYi.o: In function `main': hairtunes.c:(.text+0x3c1): undefined reference to `AES_set_decrypt_key' /tmp/ccoaOSYi.o: In function `alac_decode': hairtunes.c:(.text+0x806): undefined reference to `AES_cbc_encrypt' /tmp/ccoaOSYi.o: In function `init_rtp': hairtunes.c:(.text+0x10ef): undefined reference to `pthread_create' /tmp/ccoaOSYi.o: In function `audio_thread_func': hairtunes.c:(.text+0x1983): undefined reference to `ao_play' /tmp/ccoaOSYi.o: In function `init_output': hairtunes.c:(.text+0x1990): undefined reference to `ao_initialize' hairtunes.c:(.text+0x1995): undefined reference to `ao_default_driver_id' hairtunes.c:(.text+0x19ea): undefined reference to `ao_open_live' hairtunes.c:(.text+0x1a0f): undefined reference to `pthread_create' collect2: ld returned 1 exit status make: *** [hairtunes] Fehler 1
-
-
Zitat
Original von Uwe
Hi,Könnt ihr via airplay Musik wiedergeben? Hier klappt es nicht. Im Dialog bei Musik erscheint kein Airplay-Device, bei Video und Bildern aber schon.
iOS 4.2.1 oder 4.3 ?
4.2.1 -> geht nicht
4.3 -> weiß ich nicht