Hi,
ein komisches Verhalten legt mein VDR mal wieder an den Tag:
LCD="keins" in der sysconfig - VDR started, Bild da.
LCD="graphlcd" - VDR started, 'no signal'
Kann ich mir nicht erklären - mit 0.6.7 hatte ich das Verhalten nicht. Allerdings beim einer Debian basierten Version auch.
Wo suchen? Gerade bin ich ein wenig Ratlos..
ItsMee
Konfiguration:
easyvdr 0.6.8
linux4media usb Display
Skystar 2.6d
VGA2Scart (Nvidea)
Code
# femon
using '/dev/dvb/adapter0/frontend0'
FE: ST STV0299 DVB-S (SAT)
status 03 | signal 8cc6 | snr 75bd | ber 00002900 | unc bf96f688 |
status 03 | signal 8d1b | snr 7491 | ber 00000079 | unc bf96f688 |
status 03 | signal 8d40 | snr 7503 | ber 00000000 | unc bf96f688 |
status 03 | signal 8d1e | snr 751e | ber 00000000 | unc bf96f688 |
status 03 | signal 8bf3 | snr 74af | ber 00000000 | unc bf96f688 |
status 03 | signal 8e0f | snr 74d0 | ber 00000000 | unc bf96f688 |
status 03 | signal 8b62 | snr 74b5 | ber 00000000 | unc bf96f688 |
status 03 | signal 8bbc | snr 7491 | ber 00000000 | unc bf96f688 |
status 03 | signal 8c00 | snr 74af | ber 00000000 | unc bf96f688 |
status 03 | signal 8b8f | snr 7485 | ber 00000000 | unc bf96f688 |
status 03 | signal 8959 | snr 7518 | ber 00000000 | unc bf96f688 |Code
easyVDR:~# hwinfo --dvb
02: PCI 105.0: 11100 DVB Card
[Created at pci.281]
Unique ID: ul7N.kXehR0AesgA
Parent ID: WL76.nnqg4XqnumD
SysFS ID: /devices/pci0000:00/0000:00:09.0/0000:01:05.0
SysFS BusID: 0000:01:05.0
Hardware Class: dvb card
Model: "Techsan Electronics B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card"
Vendor: pci 0x13d0 "Techsan Electronics Co Ltd"
Device: pci 0x2103 "B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card"
SubVendor: pci 0x13d0 "Techsan Electronics Co Ltd"
SubDevice: pci 0x2103
Revision: 0x02
Driver: "b2c2_flexcop_pci"
Driver Modules: "b2c2_flexcop_pci"
Memory Range: 0xfaef0000-0xfaefffff (rw,non-prefetchable)
I/O Ports: 0xdc00-0xdc1f (rw)
IRQ: 19 (no events)
Module Alias: "pci:v000013D0d00002103sv000013D0sd00002103bc02sc80i00"
Driver Info #0:
Driver Status: b2c2-flexcop-pci is active
Driver Activation Cmd: "modprobe b2c2-flexcop-pci"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #8 (PCI bridge)