/ # cat /proc/cpuinfo machine : hdk7108 processor : 0 cpu family : sh4 cpu type : STx7108 cut : 2.x cpu flags : fpu icbi synco fpchg cache type : split (harvard) icache size : 32KiB (2-way) dcache size : 32KiB (2-way) address sizes : 32 bits physical bogomips : 500.00 / # dmesg - 00000000 ... INITRD_START - 00000000 ... INITRD_SIZE - 00000000 Booting machvec: hdk7108 Node 0: start_pfn = 0x70000, low = 0x80000 Zone PFN ranges: Normal 0x00070000 -> 0x00080000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00070000 -> 0x00080000 On node 0 totalpages: 65536 free_area_init_node: node 0, pgdat 8cbb7ba8, node_mem_map 8cbf6000 Normal zone: 512 pages used for memmap Normal zone: 0 pages reserved Normal zone: 65024 pages, LIFO batch:15 STMicroelectronics HDK7108 board initialisation STx7108 version 2.x, HOST core Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyAS1,115200 ubi.mtd=1 ubi.mtd=2 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs ro init=/sbin/init nwhwconf=device:eth0,hwaddr:00:05:9e:96:38:16 bigphysarea=3000 bpa2parts=hole_for_vid_lx:4M:0x80000000: quiet bpa2: partition 'bigphysarea' created at 0x7cdf9000, size 12000 kB (0x00bb8000 B) bpa2: partition spans low memory boundary bpa2: failed to create 'hole_for_vid_lx' partition bpa2: 'hole_for_vid_lx' partition skipped PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) PVR=04909300 CVR=60880000 PRR=0000a320 I-cache : n_ways=2 n_sets=512 way_incr=16384 I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 D-cache : n_ways=2 n_sets=512 way_incr=16384 D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 Memory: 38784k/262144k available (2903k kernel code, 905k data, 128k init) Hierarchical RCU implementation. NR_IRQS:500 Failed to enable clk CLKA0_REF, ignoring Failed to enable clk CLKA0_PLL0LS, ignoring Failed to enable clk CLKA1_REF, ignoring Failed to enable clk CLKA1_PLL0LS, ignoring Console: colour dummy device 80x25 console [ttyAS1] enabled sh_tmu: TMU0 used for clock events sh_tmu: TMU0 used for periodic clock events sh_tmu: TMU1 used as clock source Calibrating delay loop (skipped)... 500.00 BogoMIPS PRESET (lpj=250000) Mount-cache hash table entries: 512 CPU: STx7108 NET: Registered protocol family 16 Configuring FLASH for boot-from-SPI bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource TMU1 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. [STM]: [PM]: HoM support registered [STM]: [PM]: [HoM]: Early console @ 0xfd733000 ROMFS MTD (C) 2007 Red Hat, Inc. msgmni has been set to 76 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered STMicroelectronics ASC driver initialized stm-asc.0: ttyAS0 at MMIO 0xfd733000 (irq = 108) is a stm-asc stm-asc.1: ttyAS1 at MMIO 0xfd731000 (irq = 106) is a stm-asc brd: module loaded physmap platform flash device: 00800000 at 08000000 physmap-flash physmap-flash: map_probe failed NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x000000060000 nand_read_bbt: Bad block at 0x000003380000 nand_read_bbt: Bad block at 0x000004160000 nand_read_bbt: Bad block at 0x0000047a0000 Creating 5 MTD partitions on "stm-nand-flex.0": 0x000000100000-0x000000900000 : "Kernel" 0x000000900000-0x000002900000 : "Rootfs" 0x000002900000-0x000003500000 : "Data" 0x000003500000-0x000003f00000 : "Settings" 0x000003f00000-0x000007f00000 : "Update" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: attached mtd1 to ubi0 UBI: MTD device name: "Rootfs" UBI: MTD device size: 32 MiB UBI: number of good PEBs: 256 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 256 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 1/0 UBI: image sequence number: 140888535 UBI: attaching mtd2 to ubi1 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: background thread "ubi_bgt0d" started, PID 371 UBI: attached mtd2 to ubi1 UBI: MTD device name: "Data" UBI: MTD device size: 12 MiB UBI: number of good PEBs: 95 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 95 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 1/0 UBI: image sequence number: 1301023758 UBI: attaching mtd3 to ubi2 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 129024 bytes UBI: smallest flash I/O unit: 2048 UBI: sub-page size: 512 UBI: VID header offset: 512 (aligned 512) UBI: data offset: 2048 UBI: background thread "ubi_bgt1d" started, PID 374 UBI: attached mtd3 to ubi2 UBI: MTD device name: "Settings" UBI: MTD device size: 10 MiB UBI: number of good PEBs: 80 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 57 UBI: total number of reserved PEBs: 23 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 53/2 UBI: image sequence number: 0 STMMAC driver: platform registration... done! PMT module supported DWMAC1000 - user ID: 0x10, Synopsys ID: 0x33 Enhanced descriptor structure no valid MAC address;please, use ifconfig or nwhwconfig! UBI: background thread "ubi_bgt2d" started, PID 377 eth0 - (dev. name: stmmaceth - id: 1, IRQ #88 IO base addr: 0xfe730000) STMMAC MII Bus: probed eth0: PHY ID 02430d91 at 1 IRQ 0 (1:01) active nwhw_config: (eth0) setting mac address: 00:05:9e:96:38:16 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver stm_usb_probe: usb_phy_clk clock not found for stm-usb.0 stm-ehci stm-ehci.0: st-ehci stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1 stm-ehci stm-ehci.0: irq 124, io mem 0xfe0ffe00 stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected stm-ohci stm-ohci.0: stm-ohci stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2 stm-ohci stm-ohci.0: irq 127, io mem 0xfe0ffc00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected stm_usb_probe: usb_phy_clk clock not found for stm-usb.1 stm-ehci stm-ehci.1: st-ehci stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3 stm-ehci stm-ehci.1: irq 125, io mem 0xfe1ffe00 stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected stm-ohci stm-ohci.1: stm-ohci stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4 stm-ohci stm-ohci.1: irq 128, io mem 0xfe1ffc00 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected stm_usb_probe: usb_phy_clk clock not found for stm-usb.2 stm-ehci stm-ehci.2: st-ehci stm-ehci stm-ehci.2: new USB bus registered, assigned bus number 5 stm-ehci stm-ehci.2: irq 126, io mem 0xfe2ffe00 stm-ehci stm-ehci.2: USB 0.0 started, EHCI 1.00 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected stm-ohci stm-ohci.2: stm-ohci stm-ohci stm-ohci.2: new USB bus registered, assigned bus number 6 stm-ohci stm-ohci.2: irq 129, io mem 0xfe2ffc00 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver sh_tmu: TMU0 kept as earlytimer sh_tmu: TMU1 kept as earlytimer STMicroelectronics - Coprocessors st231 Init st-coprocessor-0: No RAM reserved st231.0 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- st-coprocessor-1: No RAM reserved st231.1 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- st-coprocessor-2: No RAM reserved st231.2 Coprocessor ------------------------------------------- not configured! --------------------------------------------------------------- stm_lpc device driver registered stlpm probe stlpm i2c adapter found at 2 i2c is 8fa1d018 stlpm_preparemsg Sending msg {1, 0 } stlpm_sendmsg buf 1 and address is 148 stlpm_sendmsg, size of msg 2 i2c-stm: arbitration error i2c_transfer send error is 1 stlpm_recvrespone_i2c, size of msg 4 static address of ext device 148 i2c-stm: arbitration error i2c_transfer response error is 0 stlpm_recvrespone_i2c command id 0 stlpm_recvrespone_i2c transid id 0 0 0 0 0 0 stlpm err 0 STLPM driver registered TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 [STM]: [PM]: Suspend support registered UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS: mounted read-only UBIFS: file system size: 25804800 bytes (25200 KiB, 24 MiB, 200 LEBs) UBIFS: journal size: 3741696 bytes (3654 KiB, 3 MiB, 29 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 0 bytes (0 KiB) VFS: Mounted root (ubifs filesystem) readonly on device 0:12. Freeing unused kernel memory: 128k freed stmmac: Rx Checksum Offload Engine supported TX Checksum insertion supported UBIFS: mounted UBI device 1, volume 0, name "data" UBIFS: mounted read-only UBIFS: file system size: 6451200 bytes (6300 KiB, 6 MiB, 50 LEBs) UBIFS: journal size: 1290240 bytes (1260 KiB, 1 MiB, 10 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 0 bytes (0 KiB) sttbx_early_core: module license 'ST Microelectronics' taints kernel. Disabling lock debugging due to kernel taint Load module sttbx_early_core Load module stos_core [?] by insmod (pid 515) Load module stsys_ioctl [251] by insmod (pid 517) ICS init 1 debug_flags 0x40 debug_chan 0x5 connect 0 watchdog 0 bpa2_part 'bigphysarea' ICS: Using BPA2 partition 'bigphysarea' Calling ICS_cpu_init(0, 0x1f, 0x0) insmod:ics_cpu_init:349 cpuNum 0 cpuMask 0x1f flags 0x0 insmod:ics_cpu_init:387 cpu 0 ('host') cpuMask 0x1f ics_state 8f05e000 insmod:ics_cpu_init:544 Memory usage : allocated 0 OS used 0 (+0) avail 0 EMBX init debug_flags 0x0 debug_chan 0x5 MME module init=1 debug_flags=0x0 pool_size=0 insmod:mme_init:338 Succeeded on cpu 0 mme_state 8f0df6e0 insmod:mme_init:342 Memory usage : OS used 0 (+0) avail 0 LXLOAD(rt1) : LX loaded => Base=0x7b000000 - Last=0x7b5bae7c - Size=6008444 sttbx_early_core: Exiting kernel Module Load module sttbx_early_core Load module stos_core [?] by insmod (pid 575) Load module stcommon_core [?] by insmod (pid 575) Load module stxcpu_core [0] by insmod (pid 575) Load module sttbx_core [?] by insmod (pid 575) K:STXCPU_DispatchMsg()::ERROR: "STXCPU not initialised " on line 765 in /home/rune.petersen/sandbox/zim-1800/stapisdk_a36.1/apilib/src/stxcpu/linux/stxcpu_core/../../src/stxcpu.c K:STXCPU_DispatchMsg()::ERROR: "STXCPU not initialised " on line 765 in /home/rune.petersen/sandbox/zim-1800/stapisdk_a36.1/apilib/src/stxcpu/linux/stxcpu_core/../../src/stxcpu.c Load module stevt_core [?] by insmod (pid 575) Load module stiprc_core [?] by insmod (pid 575) Load module stavmem_core [?] by insmod (pid 575) Load module stbuffer_core [?] by insmod (pid 575) Load module stclock_core [249] by insmod (pid 575) Load module stpower_core [248] by insmod (pid 575) Load module stpio_core [?] by insmod (pid 575) Load module stfdma_core [247] by insmod (pid 575) Load module stevt_relay_core [?] by insmod (pid 575) Load module stvid_proxy [?] by insmod (pid 575) Load module stvin_proxy [?] by insmod (pid 575) Load module staudlx_proxy [?] by insmod (pid 575) Load module stdenc_core [?] by insmod (pid 575) Load module stgxobj_core [?] by insmod (pid 575) Load module stclkrv_proxy [?] by insmod (pid 575) Load module stvtg_core [?] by insmod (pid 575) Load module stvtg_proxy [?] by insmod (pid 575) Load module stlayer_core [?] by insmod (pid 575) Load module stlayer_proxy [?] by insmod (pid 575) Load module stvout_core [?] by insmod (pid 575) Load module stvmix_core [?] by insmod (pid 575) Load module stvbi_core [?] by insmod (pid 575) Load module stinject_core [?] by insmod (pid 575) Load module stinject_proxy [?] by insmod (pid 575) Load module stnet_core [?] by insmod (pid 575) Load module stsp_core [?] by insmod (pid 575) Load module strm_core [?] by insmod (pid 575) Load module stpti5_proxy [?] by insmod (pid 575) Load module stfrontend_core [245] by insmod (pid 575) Load module stcommon_ioctl [244] by insmod (pid 584) Load module sttbx_ioctl [243] by insmod (pid 584) Load module stevt_ioctl [242] by insmod (pid 584) Load module stiprc_ioctl [241] by insmod (pid 584) Load module stavmem_ioctl [240] by insmod (pid 584) Load module stbuffer_ioctl [239] by insmod (pid 584) Load module stpower_ioctl [238] by insmod (pid 584) Load module stpio_ioctl [237] by insmod (pid 584) Load module stfdma_ioctl [234] by insmod (pid 584) Load module stdenc_ioctl [232] by insmod (pid 584) Load module stgxobj_ioctl [231] by insmod (pid 584) Load module stvout_ioctl [230] by insmod (pid 584) Load module stvmix_ioctl [229] by insmod (pid 584) Load module stvbi_ioctl [228] by insmod (pid 584) Load module stnet_ioctl [227] by insmod (pid 584) Load module stsys_ioctl [226] by insmod (pid 584) Load module strm_ioctl [225] by insmod (pid 584) Load module stfrontend_ioctl [224] by insmod (pid 584) eth0: no IPv6 routers present PHY: 1:01 - Link is Up - 100/Full / # / # mount rootfs on / type rootfs (rw) ubi0:rootfs on / type ubifs (ro,relatime) none on /proc type proc (rw,relatime) none on /sys type sysfs (rw,relatime) none on /dev type tmpfs (rw,relatime,size=64k,mode=755) devpts on /dev/pts type devpts (rw,relatime,mode=600) tmpfs on /tmp type tmpfs (rw,relatime) ubi1:data on /root/data type ubifs (ro,relatime) / # ps aux PID USER COMMAND 1 root init 2 root [kthreadd] 3 root [ksoftirqd/0] 4 root [events/0] 5 root [khelper] 13 root [async/mgr] 14 root [pm] 178 root [sync_supers] 180 root [bdi-default] 182 root [kblockd/0] 190 root [ksuspend_usbd] 195 root [khubd] 198 root [kseriod] 214 root [rpciod/0] 220 root [kswapd0] 221 root [aio/0] 222 root [nfsiod] 223 root [crypto/0] 341 root [mtdblockd] 371 root [ubi_bgt0d] 374 root [ubi_bgt1d] 377 root [ubi_bgt2d] 441 root [lpm_read_task] 484 root /sbin/syslogd -m 0 486 root /sbin/klogd 504 root /bin/sh /root/satip.sh 507 root telnetd -l /bin/sh -p99 534 root [ics_admin] 535 root [ics_nsrv] 536 root [ics_watchdog] 554 root [mme_manager] 577 root [STXCPU_RcvTask] 578 root [STTBX_CircBuf_O] 579 root [rootIPrRC] 580 root [STCLOCK_MASTER] 581 root [STPOWER_Master] 582 root [STFDMA_ClbckMgr] 583 root [WaitEventTask] 586 root [STTBX_ODD_RELAY] 588 root ./zim1800 591 root [STTBX_RelayTask] 592 root [STTBX_DataTask] 598 root [TUNER0] 599 root [TUNER1] 600 root [TUNER2] 602 root [TUNER3] 603 root [NET0] 614 root /root/CliConsole 629 root /bin/sh 661 root ps aux / # cat /root/satip.sh #! /bin/sh ifconfig eth0 up telnetd -l /bin/sh -p99 cd /root mount -t ubifs ubi1:data /root/data -o ro . modules/load_modules.sh modules/MakeDeviceNodes echo 256000 > /proc/sys/net/core/wmem_max ./zim1800 & sleep 1 while true; do sleep 1 /root/CliConsole done / # / # cd /root/ ~ # ls -l total 1304 -rwxr-xr-x 1 root root 17540 Oct 31 2012 CliConsole -rwxr-xr-x 1 root root 266 Oct 31 2012 checkusb.sh drwxr-xr-x 4 506 506 368 Nov 1 2012 data drwxr-xr-x 2 root root 1408 Oct 31 2012 modules -rwxr-xr-x 1 root root 272 Oct 31 2012 satip.sh -rwxr-xr-x 1 root root 615 Oct 31 2012 udhcpc.script -rwxr-xr-x 1 root root 1300300 Oct 31 2012 zim1800 ~ # ~ # ~ # cat checkusb.sh #! /bin/sh if [ "$ACTION" = add ]; then if [ -e /dev/sda1 ]; then echo possible storage! mount /dev/sda1 /mnt if [ -f /mnt/satip_enable_telnet ]; then telnetd -l /root/CliConsole fi fi fi if [ "$ACTION" = remove ]; then umount /mnt fi ~ # cat satip.sh #! /bin/sh ifconfig eth0 up telnetd -l /bin/sh -p99 cd /root mount -t ubifs ubi1:data /root/data -o ro . modules/load_modules.sh modules/MakeDeviceNodes echo 256000 > /proc/sys/net/core/wmem_max ./zim1800 & sleep 1 while true; do sleep 1 /root/CliConsole done ~ # cat udhcpc.script #!/bin/sh # udhcpc script edited by Tim Riker [ -z "$1" ] && echo "Error: should be called from udhcpc" && exit 1 case "$1" in deconfig) /bin/echo -n $interface release > /tmp/bc_dhcp_$interface ;; renew|bound) [ -n "$broadcast" ] && BROADCAST=" broadcast=$broadcast" [ -n "$subnet" ] && NETMASK=" netmask=$subnet" for i in $router ; do ROUTE="$ROUTE route=$i" done [ -n "$domain" ] && DOMAIN=" domain=$DOMAIN" for i in $dns ; do DNS="$DNS dns=$i" done /bin/echo -n $interface renew ip=$ip$BROADCAST$NETMASK$ROUTE$DNS > /tmp/bc_dhcp_$interface ;; esac exit 0 ~/modules # ls -l total 8068 -rwxr-xr-x 1 root root 8048 Oct 31 2012 MakeDeviceNodes -rw-r--r-- 1 root root 13016 Oct 31 2012 embx.ko -rw-r--r-- 1 root root 6248 Oct 31 2012 embxmailbox.ko -rw-r--r-- 1 root root 134316 Oct 31 2012 ics.ko -rw-r--r-- 1 root root 7504 Oct 31 2012 ics_user.ko -rwxr-xr-x 1 root root 8187 Oct 31 2012 load_env.sh -rwxr-xr-x 1 root root 10851 Oct 31 2012 load_modules.sh -rw-r--r-- 1 root root 5028 Oct 31 2012 load_modules_list_32BITS.txt -rw-r--r-- 1 root root 7984 Oct 31 2012 lxload.ko -rw-r--r-- 1 root root 64684 Oct 31 2012 mme.ko -rw-r--r-- 1 root root 20276 Oct 31 2012 mme_user.ko -rw-r--r-- 1 root root 6008444 Oct 31 2012 rt_7108_firmware.bin -rw-r--r-- 1 root root 1695648 Oct 31 2012 stapi_core_stripped.ko -rw-r--r-- 1 root root 188488 Oct 31 2012 stapi_ioctl_stripped.ko -rw-r--r-- 1 root root 42008 Oct 31 2012 stos_core.ko -rw-r--r-- 1 root root 10232 Oct 31 2012 stsys_ioctl.ko -rw-r--r-- 1 root root 5244 Oct 31 2012 sttbx_early_core.ko ~/modules # cat load_modules.sh #!/bin/sh ############################################################################### ## SETUP STAPI DEVICE NAME ENVIRONMENT VARIABLES ## ############################################################################### # Check if we are on virtual platform (running on x86) or not # ----------------------------------------------------------- runonvirtualplatform="no" if [ -f /proc/hce/cwd ]; then runonvirtualplatform="yes" fi # Verify if root module is specified # ---------------------------------- export PATH=$PATH:/sbin if [ -z "$MODULES_INSTALL_DIR" ] ; then if [ "$runonvirtualplatform" = "no" ] ; then export MODULES_INSTALL_DIR=/root/modules else export MODULES_INSTALL_DIR=. fi fi if [ "$runonvirtualplatform" = "no" ] ; then source $MODULES_INSTALL_DIR/load_env.sh else . $MODULES_INSTALL_DIR/load_env.sh fi # Check if we are in 32 or 29bits # ------------------------------- if [ -f $MODULES_INSTALL_DIR/load_modules_list_29BITS.txt ]; then LOAD_MODULES_LIST=$MODULES_INSTALL_DIR/load_modules_list_29BITS.txt MODE="29BITS" else MODE="32BITS" if [ -f $MODULES_INSTALL_DIR/load_modules_list_32BITS.txt ]; then LOAD_MODULES_LIST=$MODULES_INSTALL_DIR/load_modules_list_32BITS.txt else LOAD_MODULES_LIST=$MODULES_INSTALL_DIR/load_modules_list.txt fi fi ############################################################################### ## SETUP DIRECTORY ACCESS ## ############################################################################### # Verify if modules list exist # ---------------------------- if [ ! -f $LOAD_MODULES_LIST ] ; then echo "$LOAD_MODULES_LIST does not exist" exit fi # Create /dev/stapi directory if not exist # ---------------------------------------- if [ ! -e /dev/stapi ]; then mkdir -p /dev/stapi ;fi chmod 755 /dev/stapi ############################################################################### ## MODULE INSERT PROCEDURE ## ############################################################################### # Return chip version # ------------------- define_chip_info() { export chipset=`cat /proc/stsys_ioctl/chipset | cut -b1-7` export chipver=`cat /proc/stsys_ioctl/chipset | cut -b9-9` } # Create a node in /dev/ (Arg 1=node_name) # ---------------------------------------- create_node() { node_name="$1" major=`cat /proc/devices | grep "\b$node_name\b" | cut -b1-3` if [ ! -z "$major" ]; then dev="/dev/stapi/$node_name" if [ -c ${dev} ]; then if [ "$runonvirtualplatform" = "no" ] ; then cur_major=$((0x`stat -c %t $dev 2>/dev/null`)) else cur_major=`cat /proc/devices | grep $node_name|cut -d " " -f 1` fi if [ $major -ne $cur_major ]; then rm -f ${dev} 2> /dev/null mknod $dev c $major 0 || return 1 chmod 0660 $dev || return 1 fi fi if [ ! -c ${dev} ] ; then rm -f ${dev} 2> /dev/null mknod $dev c $major 0 || return 1 chmod 0660 $dev || return 1 fi fi } # Load firmware (Arg 1=video1 or audio1) # -------------------------------------- load_firmware() { if [ "$1" = "rt1" ] ; then if [ "$chipset" = "STx7108" ] ; then cat $MODULES_INSTALL_DIR/rt_7108_firmware.bin >/dev/stapi/lxload fi fi if [ "$1" = "video1" ] ; then if [ "$chipset" = "STx5206" ] ; then cat $MODULES_INSTALL_DIR/companion_5206_video_Ax.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7105" ] ; then cat $MODULES_INSTALL_DIR/companion_7105_video_Ax.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7106" ] ; then cat $MODULES_INSTALL_DIR/companion_7106_video_Ax.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7108" ] ; then if [ "$chipver" = "A" ] ; then cat $MODULES_INSTALL_DIR/companion_7108_video_Ax.bin >/dev/stapi/lxload else cat $MODULES_INSTALL_DIR/companion_7108_video_Bx.bin >/dev/stapi/lxload fi fi if [ "$chipset" = "STx7109" ] ; then cat $MODULES_INSTALL_DIR/companion_7109_video_Cx.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7111" ] ; then cat $MODULES_INSTALL_DIR/companion_7111_video_Ax.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7141" ] ; then cat $MODULES_INSTALL_DIR/companion_7141_video_Ax.bin >/dev/stapi/lxload fi if [ "$chipset" = "STxH205" ] ; then cat $MODULES_INSTALL_DIR/companion_h205_video_Ax.bin >/dev/stapi/lxload fi fi if [ "$1" = "audio1" ] ; then if [ "$chipset" = "STx5206" ] ; then cat $MODULES_INSTALL_DIR/companion_5206_audio.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7105" ] ; then cat $MODULES_INSTALL_DIR/companion_7105_audio.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7106" ] ; then cat $MODULES_INSTALL_DIR/companion_7106_audio.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7108" ] ; then cat $MODULES_INSTALL_DIR/companion_7108_audio.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7109" ] ; then cat $MODULES_INSTALL_DIR/companion_7109_audio.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7111" ] ; then cat $MODULES_INSTALL_DIR/companion_7111_audio.bin >/dev/stapi/lxload fi if [ "$chipset" = "STx7141" ] ; then cat $MODULES_INSTALL_DIR/companion_7141_audio.bin >/dev/stapi/lxload fi if [ "$chipset" = "STxH205" ] ; then cat $MODULES_INSTALL_DIR/companion_h205_audio.bin >/dev/stapi/lxload fi fi rmmod lxload } # Insert separate STAPI modules # ----------------------------- insert_separated_modules() { cat $LOAD_MODULES_LIST | grep -v "^#" | (while read mode mod_file node_name param; do if [ "$mode" != "-" ] ; then if [ "$mode" != "$MODE" ] ; then continue fi fi if [ "$param" = "-" ] ; then param="" fi if [ ! -f $MODULES_INSTALL_DIR/$mod_file ] ; then continue fi if [ "$node_name" = "lxload" ] ; then if [ "$param" = "type=rt1" ] ; then if [ ! -f "$MODULES_INSTALL_DIR/rt_7108_firmware.bin" ] ; then continue fi fi fi if [ "$mod_file" = "embxmailbox.ko" ] ; then if [ ! -f $MODULES_INSTALL_DIR/ics.ko ] ; then output=$(insmod $MODULES_INSTALL_DIR/$mod_file $param 2>&1 | cat) else output=$(insmod $MODULES_INSTALL_DIR/$mod_file 2>&1 | cat) fi else output=$(insmod $MODULES_INSTALL_DIR/$mod_file $param 2>&1 | cat) fi [ "$output" != "" ] && { echo "$output" | grep "File exists" >/dev/null && echo "Warning : $mod_file already inserted, skipping" || { echo "$output" ; exit 1 ; } ; } if [ ! "$node_name" = "-" ] ; then create_node "$node_name" fi if [ "$node_name" = "lxload" ] ; then define_chip_info if [ "$param" = "type=rt1" ] ; then load_firmware "rt1" fi if [ "$param" = "type=video1" ] ; then load_firmware "video1" fi if [ "$param" = "type=video2" ] ; then load_firmware "video2" fi if [ "$param" = "type=audio1" ] ; then load_firmware "audio1" fi if [ "$param" = "type=audio2" ] ; then load_firmware "audio2" fi fi done) } # Insert unique STAPI module # -------------------------- insert_unified_module() { # Inserting sttbx_early_core which provides traces for early loaded .ko insmod $MODULES_INSTALL_DIR/sttbx_early_core.ko # We are first inserting stsys_ioctl because we need it to know the chip and cut echo "* Looking for chipset model and version..." insmod $MODULES_INSTALL_DIR/stos_core.ko insmod $MODULES_INSTALL_DIR/stsys_ioctl.ko define_chip_info rmmod stsys_ioctl echo " $chipset $chipver detected ($MODE)" # Now we load multicom echo "* Inserting Multicom" if [ ! -f $MODULES_INSTALL_DIR/ics.ko ] ; then insmod $MODULES_INSTALL_DIR/embxshell.ko || return 1 insmod $MODULES_INSTALL_DIR/embxloopback.ko || return 1 cat $LOAD_MODULES_LIST | grep "embxmailbox\.ko" | grep "$MODE" | while read mode mod_file node_name param; do insmod $MODULES_INSTALL_DIR/embxmailbox.ko "$param"; done cat $LOAD_MODULES_LIST | grep "embxshm\.ko" | grep "$MODE"| while read mode mod_file node_name param; do insmod $MODULES_INSTALL_DIR/embxshm.ko "$param"; done cat $LOAD_MODULES_LIST | grep "mme_host\.ko" | while read mode mod_file node_name param; do insmod $MODULES_INSTALL_DIR/mme_host.ko "$param"; done else cat $LOAD_MODULES_LIST | grep "ics\.ko" | while read mode mod_file node_name param; do if [ "$param" = "-" ] ; then param="" fi insmod $MODULES_INSTALL_DIR/ics.ko "$param"; done insmod $MODULES_INSTALL_DIR/ics_user.ko || return 1 insmod $MODULES_INSTALL_DIR/embx.ko || return 1 insmod $MODULES_INSTALL_DIR/embxmailbox.ko || return 1; cat $LOAD_MODULES_LIST | grep "mme\.ko" | while read mode mod_file node_name param; do if [ "$param" = "-" ] ; then param="" fi insmod $MODULES_INSTALL_DIR/mme.ko "$param"; done insmod $MODULES_INSTALL_DIR/mme_user.ko || return 1 ; fi # Now, we load video firmware echo "* Loading companions" if [ "$chipver" = "A" ] ; then if [ -f $MODULES_INSTALL_DIR/companion_7108_video_Ax.bin ]; then insmod $MODULES_INSTALL_DIR/lxload.ko type=video1 create_node lxload load_firmware "video1" fi else if [ -f $MODULES_INSTALL_DIR/companion_7108_video_Bx.bin ]; then insmod $MODULES_INSTALL_DIR/lxload.ko type=video1 create_node lxload load_firmware "video1" fi fi if [ -f $MODULES_INSTALL_DIR/companion_7108_audio.bin ]; then insmod $MODULES_INSTALL_DIR/lxload.ko type=audio1 create_node lxload load_firmware "audio1" fi if [ "$chipset" = "STx7108" ] ; then if [ -f "$MODULES_INSTALL_DIR/rt_7108_firmware.bin" ] ; then insmod $MODULES_INSTALL_DIR/lxload.ko type=rt1 create_node lxload load_firmware "rt1" fi fi rmmod stos_core rmmod sttbx_early_core # Now we load STAPI and create nodes echo "* Inserting STAPI Module" insmod $MODULES_INSTALL_DIR/stapi_core_stripped.ko || return 1 if [ "$1" != "no_stapi_ioctl" ] ; then insmod $MODULES_INSTALL_DIR/stapi_ioctl_stripped.ko || return 1 else if [ -f $MODULES_INSTALL_DIR/stpti4_ioctl.ko ]; then insmod $MODULES_INSTALL_DIR/stpti4_ioctl.ko || return 1 fi if [ -f $MODULES_INSTALL_DIR/stpti5_ioctl.ko ]; then insmod $MODULES_INSTALL_DIR/stpti5_ioctl.ko || return 1 fi fi if [ -f $MODULES_INSTALL_DIR/staudlx_alsa.ko ]; then insmod $MODULES_INSTALL_DIR/staudlx_alsa.ko || return 1 fi # if [ "$1" != "no_stapi_ioctl" ] ; then # echo "* Creating device nodes in /dev/stapi" # cat $LOAD_MODULES_LIST | grep -v "^#" | grep -v lxload | (while read mode mod_file node_name param; do # if [ ! "$node_name" = "-" ] ; then # create_node $node_name # fi # done) # fi } # Choose between inserting severall or unified module # --------------------------------------------------- if [ $# -eq 0 ] || [ "$1" != "not_unified" ]; then if [ -f "$MODULES_INSTALL_DIR/stapi_core_stripped.ko" ] && [ -f "$MODULES_INSTALL_DIR/stapi_ioctl_stripped.ko" ]; then insert_unified_module $1 else insert_separated_modules fi else insert_separated_modules fi ~/modules # ~/modules # cat /proc/stsys_ioctl/chipset STx7108 B.0 / # uname -a Linux zim1800 2.6.32.42_stm24_V4.0-HDK7108_7108-STSDK #2 PREEMPT Wed Jul 11 14:56:22 CEST 2012 sh4 GNU/Linux /tmp # cat /var/log/messages Jan 1 00:00:00 zim1800 syslog.info syslogd started: BusyBox v1.18.5 Jan 1 00:00:00 zim1800 user.notice kernel: klogd started: BusyBox v1.18.5 (2012-07-13 16:54:16 CEST) Jan 1 00:00:00 zim1800 user.notice kernel: Linux version 2.6.32.42_stm24_V4.0-HDK7108_7108-STSDK (rune.petersen@nelson) (gcc version 4.5.2 20110124 (STMicroelectronics/Linux Base 4.5.2-78) (GCC) ) #2 PREEMPT Wed Jul 11 14:56:22 CEST 2012 Jan 1 00:00:00 zim1800 user.notice kernel: Boot params: Jan 1 00:00:00 zim1800 user.notice kernel: ... MOUNT_ROOT_RDONLY - 00000001 Jan 1 00:00:00 zim1800 user.notice kernel: ... RAMDISK_FLAGS - 00000000 Jan 1 00:00:00 zim1800 user.notice kernel: ... ORIG_ROOT_DEV - 00000200 Jan 1 00:00:00 zim1800 user.notice kernel: ... LOADER_TYPE - 00000000 Jan 1 00:00:00 zim1800 user.notice kernel: ... INITRD_START - 00000000 Jan 1 00:00:00 zim1800 user.notice kernel: ... INITRD_SIZE - 00000000 Jan 1 00:00:00 zim1800 user.notice kernel: Booting machvec: hdk7108 Jan 1 00:00:00 zim1800 user.warn kernel: Node 0: start_pfn = 0x70000, low = 0x80000 Jan 1 00:00:00 zim1800 user.warn kernel: Zone PFN ranges: Jan 1 00:00:00 zim1800 user.warn kernel: Normal 0x00070000 -> 0x00080000 Jan 1 00:00:00 zim1800 user.warn kernel: Movable zone start PFN for each node Jan 1 00:00:00 zim1800 user.warn kernel: early_node_map[1] active PFN ranges Jan 1 00:00:00 zim1800 user.warn kernel: 0: 0x00070000 -> 0x00080000 Jan 1 00:00:00 zim1800 user.debug kernel: On node 0 totalpages: 65536 Jan 1 00:00:00 zim1800 user.debug kernel: free_area_init_node: node 0, pgdat 8cbb7ba8, node_mem_map 8cbf6000 Jan 1 00:00:00 zim1800 user.debug kernel: Normal zone: 512 pages used for memmap Jan 1 00:00:00 zim1800 user.debug kernel: Normal zone: 0 pages reserved Jan 1 00:00:00 zim1800 user.debug kernel: Normal zone: 65024 pages, LIFO batch:15 Jan 1 00:00:00 zim1800 user.info kernel: STMicroelectronics HDK7108 board initialisation Jan 1 00:00:00 zim1800 user.info kernel: STx7108 version 2.x, HOST core Jan 1 00:00:00 zim1800 user.warn kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Jan 1 00:00:00 zim1800 user.notice kernel: Kernel command line: console=ttyAS1,115200 ubi.mtd=1 ubi.mtd=2 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs ro init=/sbin/init nwhwconf=device:eth0,hwaddr:00:05:9e:96:38:16 bigphysarea=3000 bpa2parts=hole_for_vid_lx:4M:0x8000000 Jan 1 00:00:00 zim1800 user.info kernel: bpa2: partition 'bigphysarea' created at 0x7cdf9000, size 12000 kB (0x00bb8000 B) Jan 1 00:00:00 zim1800 user.err kernel: bpa2: partition spans low memory boundary Jan 1 00:00:00 zim1800 user.err kernel: bpa2: failed to create 'hole_for_vid_lx' partition Jan 1 00:00:00 zim1800 user.err kernel: bpa2: 'hole_for_vid_lx' partition skipped Jan 1 00:00:00 zim1800 user.info kernel: PID hash table entries: 1024 (order: 0, 4096 bytes) Jan 1 00:00:00 zim1800 user.info kernel: Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Jan 1 00:00:00 zim1800 user.info kernel: Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Jan 1 00:00:00 zim1800 user.warn kernel: PVR=04909300 CVR=60880000 PRR=0000a320 Jan 1 00:00:00 zim1800 user.notice kernel: I-cache : n_ways=2 n_sets=512 way_incr=16384 Jan 1 00:00:00 zim1800 user.notice kernel: I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 Jan 1 00:00:00 zim1800 user.notice kernel: D-cache : n_ways=2 n_sets=512 way_incr=16384 Jan 1 00:00:00 zim1800 user.notice kernel: D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4 Jan 1 00:00:00 zim1800 user.info kernel: Memory: 38784k/262144k available (2903k kernel code, 905k data, 128k init) Jan 1 00:00:00 zim1800 user.info kernel: Hierarchical RCU implementation. Jan 1 00:00:00 zim1800 user.info kernel: NR_IRQS:500 Jan 1 00:00:00 zim1800 user.warn kernel: Failed to enable clk CLKA0_REF, ignoring Jan 1 00:00:00 zim1800 user.warn kernel: Failed to enable clk CLKA0_PLL0LS, ignoring Jan 1 00:00:00 zim1800 user.warn kernel: Failed to enable clk CLKA1_REF, ignoring Jan 1 00:00:00 zim1800 user.warn kernel: Failed to enable clk CLKA1_PLL0LS, ignoring Jan 1 00:00:00 zim1800 user.warn kernel: Console: colour dummy device 80x25 Jan 1 00:00:00 zim1800 user.info kernel: console [ttyAS1] enabled Jan 1 00:00:00 zim1800 user.info kernel: sh_tmu: TMU0 used for clock events Jan 1 00:00:00 zim1800 user.info kernel: sh_tmu: TMU0 used for periodic clock events Jan 1 00:00:00 zim1800 user.info kernel: sh_tmu: TMU1 used as clock source Jan 1 00:00:00 zim1800 user.info kernel: Calibrating delay loop (skipped)... 500.00 BogoMIPS PRESET (lpj=250000) Jan 1 00:00:00 zim1800 user.warn kernel: Mount-cache hash table entries: 512 Jan 1 00:00:00 zim1800 user.warn kernel: CPU: STx7108 Jan 1 00:00:00 zim1800 user.info kernel: NET: Registered protocol family 16 Jan 1 00:00:00 zim1800 user.info kernel: Configuring FLASH for boot-from-SPI Jan 1 00:00:00 zim1800 user.warn kernel: bio: create slab at 0 Jan 1 00:00:00 zim1800 user.notice kernel: SCSI subsystem initialized Jan 1 00:00:00 zim1800 user.info kernel: usbcore: registered new interface driver usbfs Jan 1 00:00:00 zim1800 user.info kernel: usbcore: registered new interface driver hub Jan 1 00:00:00 zim1800 user.info kernel: usbcore: registered new device driver usb Jan 1 00:00:00 zim1800 user.info kernel: Switching to clocksource TMU1 Jan 1 00:00:00 zim1800 user.info kernel: NET: Registered protocol family 2 Jan 1 00:00:00 zim1800 user.info kernel: IP route cache hash table entries: 2048 (order: 1, 8192 bytes) Jan 1 00:00:00 zim1800 user.info kernel: TCP established hash table entries: 8192 (order: 4, 65536 bytes) Jan 1 00:00:00 zim1800 user.info kernel: TCP bind hash table entries: 8192 (order: 3, 32768 bytes) Jan 1 00:00:00 zim1800 user.info kernel: TCP: Hash tables configured (established 8192 bind 8192) Jan 1 00:00:00 zim1800 user.info kernel: TCP reno registered Jan 1 00:00:00 zim1800 user.info kernel: NET: Registered protocol family 1 Jan 1 00:00:00 zim1800 user.info kernel: RPC: Registered udp transport module. Jan 1 00:00:00 zim1800 user.info kernel: RPC: Registered tcp transport module. Jan 1 00:00:00 zim1800 user.info kernel: RPC: Registered tcp NFSv4.1 backchannel transport module. Jan 1 00:00:00 zim1800 user.info kernel: [STM]: [PM]: HoM support registered Jan 1 00:00:00 zim1800 user.info kernel: [STM]: [PM]: [HoM]: Early console @ 0xfd733000 Jan 1 00:00:00 zim1800 user.info kernel: ROMFS MTD (C) 2007 Red Hat, Inc. Jan 1 00:00:00 zim1800 user.info kernel: msgmni has been set to 76 Jan 1 00:00:00 zim1800 user.info kernel: alg: No test for stdrng (krng) Jan 1 00:00:00 zim1800 user.info kernel: io scheduler noop registered Jan 1 00:00:00 zim1800 user.info kernel: io scheduler anticipatory registered (default) Jan 1 00:00:00 zim1800 user.info kernel: io scheduler deadline registered Jan 1 00:00:00 zim1800 user.info kernel: io scheduler cfq registered Jan 1 00:00:00 zim1800 user.info kernel: STMicroelectronics ASC driver initialized Jan 1 00:00:00 zim1800 user.info kernel: stm-asc.0: ttyAS0 at MMIO 0xfd733000 (irq = 108) is a stm-asc Jan 1 00:00:00 zim1800 user.info kernel: stm-asc.1: ttyAS1 at MMIO 0xfd731000 (irq = 106) is a stm-asc Jan 1 00:00:00 zim1800 user.info kernel: brd: module loaded Jan 1 00:00:00 zim1800 user.notice kernel: physmap platform flash device: 00800000 at 08000000 Jan 1 00:00:00 zim1800 user.err kernel: physmap-flash physmap-flash: map_probe failed Jan 1 00:00:00 zim1800 user.info kernel: NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) Jan 1 00:00:00 zim1800 user.debug kernel: Bad block table found at page 65472, version 0x01 Jan 1 00:00:00 zim1800 user.debug kernel: Bad block table found at page 65408, version 0x01 Jan 1 00:00:00 zim1800 user.debug kernel: nand_read_bbt: Bad block at 0x000000060000 Jan 1 00:00:00 zim1800 user.debug kernel: nand_read_bbt: Bad block at 0x000003380000 Jan 1 00:00:00 zim1800 user.debug kernel: nand_read_bbt: Bad block at 0x000004160000 Jan 1 00:00:00 zim1800 user.debug kernel: nand_read_bbt: Bad block at 0x0000047a0000 Jan 1 00:00:00 zim1800 user.notice kernel: Creating 5 MTD partitions on "stm-nand-flex.0": Jan 1 00:00:00 zim1800 user.notice kernel: 0x000000100000-0x000000900000 : "Kernel" Jan 1 00:00:00 zim1800 user.notice kernel: 0x000000900000-0x000002900000 : "Rootfs" Jan 1 00:00:00 zim1800 user.notice kernel: 0x000002900000-0x000003500000 : "Data" Jan 1 00:00:00 zim1800 user.notice kernel: 0x000003500000-0x000003f00000 : "Settings" Jan 1 00:00:00 zim1800 user.notice kernel: 0x000003f00000-0x000007f00000 : "Update" Jan 1 00:00:00 zim1800 user.notice kernel: UBI: attaching mtd1 to ubi0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: physical eraseblock size: 131072 bytes (128 KiB) Jan 1 00:00:00 zim1800 user.notice kernel: UBI: logical eraseblock size: 129024 bytes Jan 1 00:00:00 zim1800 user.notice kernel: UBI: smallest flash I/O unit: 2048 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: sub-page size: 512 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: VID header offset: 512 (aligned 512) Jan 1 00:00:00 zim1800 user.notice kernel: UBI: data offset: 2048 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: attached mtd1 to ubi0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: MTD device name: "Rootfs" Jan 1 00:00:00 zim1800 user.notice kernel: UBI: MTD device size: 32 MiB Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of good PEBs: 256 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of bad PEBs: 0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: max. allowed volumes: 128 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: wear-leveling threshold: 4096 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of internal volumes: 1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of user volumes: 1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: available PEBs: 0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: total number of reserved PEBs: 256 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of PEBs reserved for bad PEB handling: 2 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: max/mean erase counter: 1/0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: image sequence number: 140888535 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: attaching mtd2 to ubi1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: physical eraseblock size: 131072 bytes (128 KiB) Jan 1 00:00:00 zim1800 user.notice kernel: UBI: logical eraseblock size: 129024 bytes Jan 1 00:00:00 zim1800 user.notice kernel: UBI: smallest flash I/O unit: 2048 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: sub-page size: 512 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: VID header offset: 512 (aligned 512) Jan 1 00:00:00 zim1800 user.notice kernel: UBI: data offset: 2048 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: background thread "ubi_bgt0d" started, PID 371 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: attached mtd2 to ubi1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: MTD device name: "Data" Jan 1 00:00:00 zim1800 user.notice kernel: UBI: MTD device size: 12 MiB Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of good PEBs: 95 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of bad PEBs: 1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: max. allowed volumes: 128 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: wear-leveling threshold: 4096 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of internal volumes: 1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of user volumes: 1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: available PEBs: 0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: total number of reserved PEBs: 95 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of PEBs reserved for bad PEB handling: 2 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: max/mean erase counter: 1/0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: image sequence number: 1301023758 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: attaching mtd3 to ubi2 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: physical eraseblock size: 131072 bytes (128 KiB) Jan 1 00:00:00 zim1800 user.notice kernel: UBI: logical eraseblock size: 129024 bytes Jan 1 00:00:00 zim1800 user.notice kernel: UBI: smallest flash I/O unit: 2048 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: sub-page size: 512 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: VID header offset: 512 (aligned 512) Jan 1 00:00:00 zim1800 user.notice kernel: UBI: data offset: 2048 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: background thread "ubi_bgt1d" started, PID 374 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: attached mtd3 to ubi2 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: MTD device name: "Settings" Jan 1 00:00:00 zim1800 user.notice kernel: UBI: MTD device size: 10 MiB Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of good PEBs: 80 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of bad PEBs: 0 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: max. allowed volumes: 128 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: wear-leveling threshold: 4096 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of internal volumes: 1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of user volumes: 1 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: available PEBs: 57 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: total number of reserved PEBs: 23 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: number of PEBs reserved for bad PEB handling: 2 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: max/mean erase counter: 53/2 Jan 1 00:00:00 zim1800 user.notice kernel: UBI: image sequence number: 0 Jan 1 00:00:00 zim1800 user.info kernel: STMMAC driver: Jan 1 00:00:00 zim1800 user.info kernel: platform registration... Jan 1 00:00:00 zim1800 user.info kernel: done! Jan 1 00:00:00 zim1800 user.info kernel: PMT module supported Jan 1 00:00:00 zim1800 user.info kernel: DWMAC1000 - user ID: 0x10, Synopsys ID: 0x33 Jan 1 00:00:00 zim1800 user.info kernel: Enhanced descriptor structure Jan 1 00:00:00 zim1800 user.warn kernel: no valid MAC address;please, use ifconfig or nwhwconfig! Jan 1 00:00:00 zim1800 user.notice kernel: UBI: background thread "ubi_bgt2d" started, PID 377 Jan 1 00:00:00 zim1800 user.info kernel: eth0 - (dev. name: stmmaceth - id: 1, IRQ #88 Jan 1 00:00:00 zim1800 user.info kernel: IO base addr: 0xfe730000) Jan 1 00:00:00 zim1800 user.info kernel: STMMAC MII Bus: probed Jan 1 00:00:00 zim1800 user.info kernel: eth0: PHY ID 02430d91 at 1 IRQ 0 (1:01) active Jan 1 00:00:00 zim1800 user.info kernel: nwhw_config: (eth0) setting mac address: 00:05:9e:96:38:16 Jan 1 00:00:00 zim1800 user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Jan 1 00:00:00 zim1800 user.info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Jan 1 00:00:00 zim1800 user.warn kernel: stm_usb_probe: usb_phy_clk clock not found for stm-usb.0 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.0: st-ehci Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.0: irq 124, io mem 0xfe0ffe00 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00 Jan 1 00:00:00 zim1800 user.info kernel: usb usb1: configuration #1 chosen from 1 choice Jan 1 00:00:00 zim1800 user.info kernel: hub 1-0:1.0: USB hub found Jan 1 00:00:00 zim1800 user.info kernel: hub 1-0:1.0: 1 port detected Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.0: stm-ohci Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2 Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.0: irq 127, io mem 0xfe0ffc00 Jan 1 00:00:00 zim1800 user.info kernel: usb usb2: configuration #1 chosen from 1 choice Jan 1 00:00:00 zim1800 user.info kernel: hub 2-0:1.0: USB hub found Jan 1 00:00:00 zim1800 user.info kernel: hub 2-0:1.0: 1 port detected Jan 1 00:00:00 zim1800 user.warn kernel: stm_usb_probe: usb_phy_clk clock not found for stm-usb.1 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.1: st-ehci Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.1: irq 125, io mem 0xfe1ffe00 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00 Jan 1 00:00:00 zim1800 user.info kernel: usb usb3: configuration #1 chosen from 1 choice Jan 1 00:00:00 zim1800 user.info kernel: hub 3-0:1.0: USB hub found Jan 1 00:00:00 zim1800 user.info kernel: hub 3-0:1.0: 1 port detected Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.1: stm-ohci Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4 Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.1: irq 128, io mem 0xfe1ffc00 Jan 1 00:00:00 zim1800 user.info kernel: usb usb4: configuration #1 chosen from 1 choice Jan 1 00:00:00 zim1800 user.info kernel: hub 4-0:1.0: USB hub found Jan 1 00:00:00 zim1800 user.info kernel: hub 4-0:1.0: 1 port detected Jan 1 00:00:00 zim1800 user.warn kernel: stm_usb_probe: usb_phy_clk clock not found for stm-usb.2 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.2: st-ehci Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.2: new USB bus registered, assigned bus number 5 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.2: irq 126, io mem 0xfe2ffe00 Jan 1 00:00:00 zim1800 user.info kernel: stm-ehci stm-ehci.2: USB 0.0 started, EHCI 1.00 Jan 1 00:00:00 zim1800 user.info kernel: usb usb5: configuration #1 chosen from 1 choice Jan 1 00:00:00 zim1800 user.info kernel: hub 5-0:1.0: USB hub found Jan 1 00:00:00 zim1800 user.info kernel: hub 5-0:1.0: 1 port detected Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.2: stm-ohci Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.2: new USB bus registered, assigned bus number 6 Jan 1 00:00:00 zim1800 user.info kernel: stm-ohci stm-ohci.2: irq 129, io mem 0xfe2ffc00 Jan 1 00:00:00 zim1800 user.info kernel: usb usb6: configuration #1 chosen from 1 choice Jan 1 00:00:00 zim1800 user.info kernel: hub 6-0:1.0: USB hub found Jan 1 00:00:00 zim1800 user.info kernel: hub 6-0:1.0: 1 port detected Jan 1 00:00:00 zim1800 user.info kernel: Initializing USB Mass Storage driver... Jan 1 00:00:00 zim1800 user.info kernel: usbcore: registered new interface driver usb-storage Jan 1 00:00:00 zim1800 user.info kernel: USB Mass Storage support registered. Jan 1 00:00:00 zim1800 user.info kernel: i2c /dev entries driver Jan 1 00:00:00 zim1800 user.info kernel: sh_tmu: TMU0 kept as earlytimer Jan 1 00:00:00 zim1800 user.info kernel: sh_tmu: TMU1 kept as earlytimer Jan 1 00:00:00 zim1800 user.warn kernel: STMicroelectronics - Coprocessors st231 Init Jan 1 00:00:00 zim1800 user.warn kernel: st-coprocessor-0: No RAM reserved Jan 1 00:00:00 zim1800 user.warn kernel: st231.0 Coprocessor ------------------------------------------- Jan 1 00:00:00 zim1800 user.warn kernel: not configured! Jan 1 00:00:00 zim1800 user.warn kernel: --------------------------------------------------------------- Jan 1 00:00:00 zim1800 user.warn kernel: st-coprocessor-1: No RAM reserved Jan 1 00:00:00 zim1800 user.warn kernel: st231.1 Coprocessor ------------------------------------------- Jan 1 00:00:00 zim1800 user.warn kernel: not configured! Jan 1 00:00:00 zim1800 user.warn kernel: --------------------------------------------------------------- Jan 1 00:00:00 zim1800 user.warn kernel: st-coprocessor-2: No RAM reserved Jan 1 00:00:00 zim1800 user.warn kernel: st231.2 Coprocessor ------------------------------------------- Jan 1 00:00:00 zim1800 user.warn kernel: not configured! Jan 1 00:00:00 zim1800 user.warn kernel: --------------------------------------------------------------- Jan 1 00:00:00 zim1800 user.info kernel: stm_lpc device driver registered Jan 1 00:00:00 zim1800 user.warn kernel: stlpm probe Jan 1 00:00:00 zim1800 user.warn kernel: stlpm i2c adapter found at 2 i2c is 8fa1d018 Jan 1 00:00:00 zim1800 user.warn kernel: stlpm_preparemsg Jan 1 00:00:00 zim1800 user.warn kernel: Sending msg {1, 0 } Jan 1 00:00:00 zim1800 user.warn kernel: stlpm_sendmsg buf 1 and address is 148 Jan 1 00:00:00 zim1800 user.warn kernel: stlpm_sendmsg, size of msg 2 Jan 1 00:00:00 zim1800 user.err kernel: i2c-stm: arbitration error Jan 1 00:00:00 zim1800 user.warn kernel: i2c_transfer send error is 1 Jan 1 00:00:00 zim1800 user.warn kernel: stlpm_recvrespone_i2c, size of msg 4 static address of ext device 148 Jan 1 00:00:00 zim1800 user.err kernel: i2c-stm: arbitration error Jan 1 00:00:00 zim1800 user.warn kernel: i2c_transfer response error is 0 Jan 1 00:00:00 zim1800 user.warn kernel: stlpm_recvrespone_i2c command id 0 Jan 1 00:00:00 zim1800 user.warn kernel: stlpm_recvrespone_i2c transid id 0 Jan 1 00:00:00 zim1800 user.warn kernel: 0 0 0 0 0 Jan 1 00:00:00 zim1800 user.warn kernel: stlpm err 0 Jan 1 00:00:00 zim1800 user.warn kernel: STLPM driver registered Jan 1 00:00:00 zim1800 user.info kernel: TCP cubic registered Jan 1 00:00:00 zim1800 user.info kernel: NET: Registered protocol family 10 Jan 1 00:00:00 zim1800 user.info kernel: IPv6 over IPv4 tunneling driver Jan 1 00:00:00 zim1800 user.info kernel: NET: Registered protocol family 17 Jan 1 00:00:00 zim1800 user.info kernel: [STM]: [PM]: Suspend support registered Jan 1 00:00:00 zim1800 user.notice kernel: UBIFS: mounted UBI device 0, volume 0, name "rootfs" Jan 1 00:00:00 zim1800 user.notice kernel: UBIFS: mounted read-only Jan 1 00:00:00 zim1800 user.notice kernel: UBIFS: file system size: 25804800 bytes (25200 KiB, 24 MiB, 200 LEBs) Jan 1 00:00:00 zim1800 user.notice kernel: UBIFS: journal size: 3741696 bytes (3654 KiB, 3 MiB, 29 LEBs) Jan 1 00:00:00 zim1800 user.notice kernel: UBIFS: media format: w4/r0 (latest is w4/r0) Jan 1 00:00:00 zim1800 user.notice kernel: UBIFS: default compressor: lzo Jan 1 00:00:00 zim1800 user.notice kernel: UBIFS: reserved for root: 0 bytes (0 KiB) Jan 1 00:00:00 zim1800 user.warn kernel: VFS: Mounted root (ubifs filesystem) readonly on device 0:12. Jan 1 00:00:00 zim1800 user.warn kernel: Freeing unused kernel memory: 128k freed Jan 1 00:00:01 zim1800 daemon.info init: starting pid 504, tty '/dev/ttyAS1': '/root/satip.sh ' Jan 1 00:00:01 zim1800 user.info kernel: stmmac: Rx Checksum Offload Engine supported Jan 1 00:00:01 zim1800 user.info kernel: TX Checksum insertion supported Jan 1 00:00:01 zim1800 user.notice kernel: UBIFS: mounted UBI device 1, volume 0, name "data" Jan 1 00:00:01 zim1800 user.notice kernel: UBIFS: mounted read-only Jan 1 00:00:01 zim1800 user.notice kernel: UBIFS: file system size: 6451200 bytes (6300 KiB, 6 MiB, 50 LEBs) Jan 1 00:00:01 zim1800 user.notice kernel: UBIFS: journal size: 1290240 bytes (1260 KiB, 1 MiB, 10 LEBs) Jan 1 00:00:01 zim1800 user.notice kernel: UBIFS: media format: w4/r0 (latest is w4/r0) Jan 1 00:00:01 zim1800 user.notice kernel: UBIFS: default compressor: lzo Jan 1 00:00:01 zim1800 user.notice kernel: UBIFS: reserved for root: 0 bytes (0 KiB) Jan 1 00:00:01 zim1800 user.warn kernel: sttbx_early_core: module license 'ST Microelectronics' taints kernel. Jan 1 00:00:01 zim1800 user.warn kernel: Disabling lock debugging due to kernel taint Jan 1 00:00:01 zim1800 user.info kernel: Load module sttbx_early_core Jan 1 00:00:01 zim1800 user.alert kernel: Load module stos_core [?] by insmod (pid 515) Jan 1 00:00:01 zim1800 user.alert kernel: Load module stsys_ioctl [251] by insmod (pid 517) Jan 1 00:00:01 zim1800 user.warn kernel: ICS init 1 debug_flags 0x40 debug_chan 0x5 connect 0 watchdog 0 bpa2_part 'bigphysarea' Jan 1 00:00:01 zim1800 user.warn kernel: ICS: Using BPA2 partition 'bigphysarea' Jan 1 00:00:01 zim1800 user.warn kernel: Calling ICS_cpu_init(0, 0x1f, 0x0) Jan 1 00:00:01 zim1800 user.debug kernel: insmod:ics_cpu_init:349 cpuNum 0 cpuMask 0x1f flags 0x0 Jan 1 00:00:01 zim1800 user.debug kernel: insmod:ics_cpu_init:387 cpu 0 ('host') cpuMask 0x1f ics_state 8f05e000 Jan 1 00:00:01 zim1800 user.debug kernel: insmod:ics_cpu_init:544 Memory usage : allocated 0 OS used 0 (+0) avail 0 Jan 1 00:00:01 zim1800 user.warn kernel: EMBX init debug_flags 0x0 debug_chan 0x5 Jan 1 00:00:01 zim1800 user.warn kernel: MME module init=1 debug_flags=0x0 pool_size=0 Jan 1 00:00:01 zim1800 user.debug kernel: insmod:mme_init:338 Succeeded on cpu 0 mme_state 8f0df6e0 Jan 1 00:00:01 zim1800 user.debug kernel: insmod:mme_init:342 Memory usage : OS used 0 (+0) avail 0 Jan 1 00:00:04 zim1800 user.info kernel: LXLOAD(rt1) : LX loaded => Base=0x7b000000 - Last=0x7b5bae7c - Size=6008444 Jan 1 00:00:04 zim1800 user.info kernel: sttbx_early_core: Exiting kernel Module Jan 1 00:00:05 zim1800 user.info kernel: Load module sttbx_early_core Jan 1 00:00:05 zim1800 user.alert kernel: Load module stos_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stcommon_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stxcpu_core [0] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module sttbx_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.warn kernel: K:STXCPU_DispatchMsg()::ERROR: "STXCPU not initialised Jan 1 00:00:05 zim1800 user.warn kernel: " on line 765 in /home/rune.petersen/sandbox/zim-1800/stapisdk_a36.1/apilib/src/stxcpu/linux/stxcpu_core/../../src/stxcpu.c^M Jan 1 00:00:05 zim1800 user.warn kernel: K:STXCPU_DispatchMsg()::ERROR: "STXCPU not initialised Jan 1 00:00:05 zim1800 user.warn kernel: " on line 765 in /home/rune.petersen/sandbox/zim-1800/stapisdk_a36.1/apilib/src/stxcpu/linux/stxcpu_core/../../src/stxcpu.c^M Jan 1 00:00:05 zim1800 user.alert kernel: Load module stevt_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.warn kernel: Load module stiprc_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stavmem_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stbuffer_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stclock_core [249] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stpower_core [248] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stpio_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stfdma_core [247] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stevt_relay_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvid_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvin_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module staudlx_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stdenc_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stgxobj_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stclkrv_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvtg_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvtg_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stlayer_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stlayer_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvout_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvmix_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvbi_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stinject_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stinject_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stnet_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stsp_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module strm_core [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stpti5_proxy [?] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stfrontend_core [245] by insmod (pid 575) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stcommon_ioctl [244] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module sttbx_ioctl [243] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stevt_ioctl [242] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stiprc_ioctl [241] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stavmem_ioctl [240] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stbuffer_ioctl [239] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stpower_ioctl [238] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stpio_ioctl [237] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stfdma_ioctl [234] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stdenc_ioctl [232] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stgxobj_ioctl [231] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvout_ioctl [230] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvmix_ioctl [229] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stvbi_ioctl [228] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stnet_ioctl [227] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stsys_ioctl [226] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module strm_ioctl [225] by insmod (pid 584) Jan 1 00:00:05 zim1800 user.alert kernel: Load module stfrontend_ioctl [224] by insmod (pid 584) Jan 1 00:00:11 zim1800 user.debug kernel: eth0: no IPv6 routers present Jan 1 00:00:50 zim1800 user.info kernel: PHY: 1:01 - Link is Up - 100/Full /tmp #