one order, mobility grouping on.  Total pages: 32015
Kernel command line: auto BOOT_IMAGE=zen2vdr-r2 ro root=302 quiet ro console=tty4 agpgart video=i810fb:vram:8,xres:720,yres:576,bpp:24,hsync1:27,hsync2:55,vsync1:50,vsync2:50,accel,mtrr
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Subtract (24 early reservations)
  #0 [0001000000 - 000141e370]   TEXT DATA BSS
  #1 [000009f800 - 0000100000]   BIOS reserved
  #2 [000141f000 - 0001425140]             BRK
  #3 [0000010000 - 0000011000]         PGTABLE
  #4 [0001425140 - 0001525140]         BOOTMEM
  #5 [000141e380 - 000141e384]         BOOTMEM
  #6 [000141e3a0 - 000141e420]         BOOTMEM
  #7 [000141e420 - 000141e42c]         BOOTMEM
  #8 [000141e440 - 000141e840]         BOOTMEM
  #9 [000141e840 - 000141e958]         BOOTMEM
  #10 [000141e960 - 000141e9a0]         BOOTMEM
  #11 [000141e9a0 - 000141e9e0]         BOOTMEM
  #12 [000141e9e0 - 000141ea20]         BOOTMEM
  #13 [000141ea20 - 000141ea60]         BOOTMEM
  #14 [000141ea60 - 000141eaa0]         BOOTMEM
  #15 [000141eaa0 - 000141eae0]         BOOTMEM
  #16 [000141eae0 - 000141eb20]         BOOTMEM
  #17 [000141eb20 - 000141eb60]         BOOTMEM
  #18 [000141eb60 - 000141eba0]         BOOTMEM
  #19 [000141eba0 - 000141ec45]         BOOTMEM
  #20 [000141ec60 - 000141ed05]         BOOTMEM
  #21 [0001525140 - 0001525940]         BOOTMEM
  #22 [0001525940 - 0001535940]         BOOTMEM
  #23 [0001535940 - 000153d940]         BOOTMEM
Memory: 123700k/129524k available (2809k kernel code, 5372k reserved, 1031k data, 244k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffe4000 - 0xfffff000   ( 108 kB)
    vmalloc : 0xc867d000 - 0xfffe2000   ( 889 MB)
    lowmem  : 0xc0000000 - 0xc7e7d000   ( 126 MB)
      .init : 0xc13c1000 - 0xc13fe000   ( 244 kB)
      .data : 0xc12be6ce - 0xc13c031c   (1031 kB)
      .text : 0xc1000000 - 0xc12be6ce   (2809 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Hierarchical RCU implementation.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:16
CPU 0 irqstacks, hard=c1398000 soft=c1399000
Console: colour VGA+ 80x25
console [tty4] enabled
Fast TSC calibration using PIT
Detected 731.175 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 1462.35 BogoMIPS (lpj=7311750)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
Performance Events: 
no APIC, boot with the "lapic" boot parameter to force-enable it.
no hardware sampling interrupt available.
p6 PMU driver.
... version:                0
... bit width:              32
... generic registers:      2
... value mask:             00000000ffffffff
... max period:             000000007fffffff
... fixed-purpose events:   0
... event mask:             0000000000000003
CPU: Mobile Intel(R) Celeron(TM) CPU          733MHz stepping 04
devtmpfs: initialized
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd994, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: Interpreter disabled.
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
pci 0000:00:02.0: reg 10: [mem 0xf8000000-0xfbffffff pref]
pci 0000:00:02.0: reg 14: [mem 0xf4000000-0xf407ffff]
pci 0000:00:1f.0: quirk: [io  0x1000-0x107f] claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: [io  0x1180-0x11bf] claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 20: [io  0x1800-0x180f]
pci 0000:00:1f.2: reg 20: [io  0x1820-0x183f]
pci 0000:00:1f.3: reg 20: [io  0x1810-0x181f]
pci 0000:00:1f.4: reg 20: [io  0x1840-0x185f]
pci 0000:00:1f.5: reg 10: [io  0x1c00-0x1cff]
pci 0000:00:1f.5: reg 14: [io  0x1880-0x18bf]
pci 0000:00:1f.6: reg 10: [io  0x2400-0x24ff]
pci 0000:00:1f.6: reg 14: [io  0x2000-0x207f]
pci 0000:01:04.0: reg 10: [mem 0xf5000000-0xf5ffffff]
pci 0000:01:04.2: reg 10: [mem 0xf6000000-0xf6ffffff]
pci 0000:01:05.0: reg 20: [io  0x3040-0x305f]
pci 0000:01:05.0: supports D1 D2
pci 0000:01:05.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:05.0: PME# disabled
pci 0000:01:05.1: reg 20: [io  0x3060-0x307f]
pci 0000:01:05.1: supports D1 D2
pci 0000:01:05.1: PME# supported from D0 D1 D2 D3hot
pci 0000:01:05.1: PME# disabled
pci 0000:01:05.2: reg 10: [mem 0xf4101000-0xf41010ff]
pci 0000:01:05.2: supports D1 D2
pci 0000:01:05.2: PME# supported from D0 D1 D2 D3hot
pci 0000:01:05.2: PME# disabled
pci 0000:01:08.0: reg 10: [mem 0xf4100000-0xf4100fff]
pci 0000:01:08.0: reg 14: [io  0x3000-0x303f]
pci 0000:01:08.0: supports D1 D2
pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:08.0: PME# disabled
pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
pci 0000:00:1e.0:   bridge window [io  0x3000-0x3fff]
pci 0000:00:1e.0:   bridge window [mem 0xf4100000-0xf6ffffff]
pci 0000:00:1e.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
PCI: pci_cache_line_size set to 32 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff 
reserve RAM buffer: 0000000007e7d000 - 0000000007ffffff 
Switching to clocksource tsc
pnp: PnP ACPI: disabled
pci 0000:00:1e.0: PCI bridge to [bus 01-01]
pci 0000:00:1e.0:   bridge window [io  0x3000-0x3fff]
pci 0000:00:1e.0:   bridge window [mem 0xf4100000-0xf6ffffff]
pci 0000:00:1e.0:   bridge window [mem pref disabled]
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
pci_bus 0000:01: resource 1 [mem 0xf4100000-0xf6ffffff]
pci_bus 0000:01: resource 4 [io  0x0000-0xffff]
pci_bus 0000:01: resource 5 [mem 0x00000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:02.0: Boot video device
pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
PCI: CLS 32 bytes, default 32
platform rtc_cmos: registered platform RTC device (no PNP device found)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Btrfs loaded
aufs 2.1-standalone.tree-36-20101206
msgmni has been set to 241
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
Real Time Clock Driver v1.12b
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel i815 Chipset
agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
i810-i2c: Probe DDC1 Bus
i2c i2c-0: unable to read EDID block.
i2c i2c-0: unable to read EDID block.
i2c i2c-0: unable to read EDID block.
i810-i2c: Probe DDC2 Bus
i2c i2c-1: unable to read EDID block.
i2c i2c-1: unable to read EDID block.
i2c i2c-1: unable to read EDID block.
i810-i2c: Probe DDC3 Bus
i810fb_init_pci: Unable to get Mode Database
Console: switching to colour frame buffer device 90x36
I810FB: fb0         : Intel(R) 815 (Internal Graphics with AGP) Framebuffer Device v0.9.0
I810FB: Video RAM   : 8192K
I810FB: Monitor     : H: 27-55 KHz V: 50-50 Hz
I810FB: Mode        : 720x576-24bpp@50Hz
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
loop: module loaded
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x244b rev 0x05)
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1800-0x1807
    ide1: BM-DMA at 0x1808-0x180f
Probing IDE interface ide0...
hda: DMSTORAGE FDM032MAA, ATA DISK drive
hda: tPIO > 2, assuming tPIO = 2
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO2
hda: tPIO > 2, assuming tPIO = 2
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO2
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
ide-gd driver 1.18
hda: max request size: 128KiB
hda: 62496 sectors (31 MB) w/2KiB Cache, CHS=62/16/63
 hda: hda1 hda2
hda: p2 size 53120 extends beyond EOD, enabling native capacity
 hda: hda1 hda2
hda: p2 size 53120 extends beyond EOD, truncated
ide-cd driver 5.00
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:01:05.2: EHCI Host Controller
ehci_hcd 0000:01:05.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:01:05.2: irq 10, io mem 0xf4101000
ehci_hcd 0000:01:05.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1f.2: setting latency timer to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1f.2: irq 10, io base 0x00001820
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1f.4: setting latency timer to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1f.4: irq 12, io base 0x00001840
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:01:05.0: UHCI Host Controller
uhci_hcd 0000:01:05.0: new USB bus registered, assigned bus number 4
uhci_hcd 0000:01:05.0: irq 5, io base 0x00003040
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:01:05.1: UHCI Host Controller
uhci_hcd 0000:01:05.1: new USB bus registered, assigned bus number 5
uhci_hcd 0000:01:05.1: irq 9, io base 0x00003060
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
hub 3-0:1.0: over-current change on port 1
hub 3-0:1.0: over-current change on port 2
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
cpuidle: using governor ladder
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
usb 1-2: new high speed USB device using ehci_hcd and address 2
VFS: Mounted root (squashfs filesystem) readonly on device 3:2.
devtmpfs: mounted
Freeing unused kernel memory: 244k freed
scsi0 : usb-storage 1-2:1.0
scsi 0:0:0:0: Direct-Access     FSC      Memorybird P     2.00 PQ: 0 ANSI: 2
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 1009664 512-byte logical blocks: (516 MB/493 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1 sda2
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
cx88xx: Unknown symbol v4l2_norm_to_name (err 0)
cx88xx: Unknown symbol v4l2_i2c_new_subdev_cfg (err 0)
cx88xx: Unknown symbol videobuf_dma_free (err 0)
cx88xx: Unknown symbol videobuf_waiton (err 0)
cx88xx: Unknown symbol __ir_input_register (err 0)
cx88xx: Unknown symbol ir_extract_bits (err 0)
cx88xx: Unknown symbol btcx_riscmem_alloc (err 0)
cx88xx: Unknown symbol tveeprom_read (err 0)
cx88xx: Unknown symbol btcx_riscmem_free (err 0)
cx88xx: Unknown symbol videobuf_dma_unmap (err 0)
cx88xx: Unknown symbol ir_decode_biphase (err 0)
cx88xx: Unknown symbol ir_keydown (err 0)
cx88xx: Unknown symbol video_device_alloc (err 0)
cx88xx: Unknown symbol v4l2_device_register (err 0)
cx88xx: Unknown symbol ir_input_unregister (err 0)
cx88xx: Unknown symbol ir_repeat (err 0)
cx88xx: Unknown symbol v4l2_i2c_tuner_addrs (err 0)
cx88xx: Unknown symbol v4l2_device_unregister (err 0)
cx88xx: Unknown symbol tveeprom_hauppauge_analog (err 0)
cx88xx: Unknown symbol video_device_release (err 0)
cx88xx: Unknown symbol get_rc_map (err 0)
cx88xx: Unknown symbol ir_decode_pulsedistance (err 0)
cx88xx: Unknown symbol ir_dump_samples (err 0)
cx88xx: Unknown symbol videobuf_to_dma (err 0)
Linux video capture interface: v2.00
cx88_dvb: Unknown symbol cx8802_get_driver (err 0)
cx88_dvb: Unknown symbol videobuf_dvb_alloc_frontend (err 0)
cx88_dvb: Unknown symbol cx8802_unregister_driver (err 0)
cx88_dvb: Unknown symbol cx8802_register_driver (err 0)
cx88_dvb: Unknown symbol videobuf_dvb_get_frontend (err 0)
cx88_dvb: Unknown symbol cx8802_buf_prepare (err 0)
cx88_dvb: Unknown symbol dvb_frontend_detach (err 0)
cx88_dvb: Unknown symbol videobuf_dvb_unregister_bus (err 0)
cx88_dvb: Unknown symbol videobuf_dvb_register_bus (err 0)
cx88_dvb: Unknown symbol dvb_unregister_frontend (err 0)
cx88_dvb: Unknown symbol cx8802_buf_queue (err 0)
cx88_dvb: Unknown symbol videobuf_dvb_dealloc_frontends (err 0)
cx88_dvb: Unknown symbol videobuf_dvb_find_frontend (err 0)
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.8 loaded
cx88[0]: subsystem: 18ac:dc00, board: Samsung SMT 7020 DVB-S [card=84,autodetected], frontend(s): 1
cx88[0]: TV tuner type 4, Radio tuner type -1
cx88[0]/2: cx2388x 8802 Driver Manager
cx88[0]/2: found at 0000:01:04.2, rev: 5, irq: 11, latency: 64, mmio: 0xf6000000
cx88/2: cx2388x dvb driver version 0.0.8 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 18ac:dc00, board: Samsung SMT 7020 DVB-S [card=84]
cx88[0]/2: cx2388x based DVB/ATSC card
cx8802_alloc_frontends() allocating 1 frontend(s)
DVB: registering new adapter (cx88[0])
DVB: registering adapter 0 frontend 0 (ST STV0299 DVB-S)...
Intel ICH 0000:00:1f.5: setting latency timer to 64
intel8x0_measure_ac97_clock: measured 50967 usecs (2450 samples)
intel8x0: clocking to 48000
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:01:08.0: setting latency timer to 64
e100 0000:01:08.0: PME# disabled
e100 0000:01:08.0: eth0: addr 0xf4100000, irq 7, MAC addr 00:00:f0:20:c7:68
w83627hf: Found W83627HF chip at 0x290
e100 0000:01:08.0: eth0: NIC Link is Up 100 Mbps Full Duplex
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
sshd (996): /proc/996/oom_adj is deprecated, please use /proc/996/oom_score_adj instead.
i2c i2c-1: sendbytes: NAK bailout.
i2c i2c-1: sendbytes: NAK bailout.
CIFS VFS: Send error in QFSAttributeInfo = -5
CIFS VFS: cifs_read_super: get root inode failed
