ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   19.012595] usb usb5: configuration #1 chosen from 1 choice
[   19.016563] hub 5-0:1.0: USB hub found
[   19.016593] hub 5-0:1.0: 8 ports detected
[   19.487060] usbcore: registered new interface driver hiddev
[   19.692937] usb 5-4: new high speed USB device using ehci_hcd and address 2
[   19.811059] usb 5-4: configuration #1 chosen from 1 choice
[   20.240701] usb 5-8: new high speed USB device using ehci_hcd and address 4
[   20.360813] usb 5-8: configuration #1 chosen from 1 choice
[   20.382843] usbcore: registered new interface driver usbhid
[   20.382857] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[   20.477979] EXT3 FS on sda1, internal journal
[   20.588611] usb 3-2: new full speed USB device using uhci_hcd and address 2
[   20.687774] kjournald starting.  Commit interval 5 seconds
[   20.688397] EXT3 FS on sda2, internal journal
[   20.688410] EXT3-fs: mounted filesystem with ordered data mode.
[   20.758649] usb 3-2: configuration #1 chosen from 1 choice
[   21.114484] ata1: soft resetting port
[   21.296708] ata1.00: configured for UDMA/100
[   21.296720] ata1: EH pending after completion, repeating EH (cnt=4)
[   21.296741] ata1: soft resetting port
[   21.484618] ata1.00: configured for UDMA/100
[   21.484637] ata1: EH complete
[   21.513816] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[   21.528318] sd 0:0:0:0: [sda] Write Protect is off
[   21.528334] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   21.539615] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   21.550296] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[   21.550598] sd 0:0:0:0: [sda] Write Protect is off
[   21.550608] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   21.551200] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.062390] ata2: soft resetting port
[   22.076433] ata1: soft resetting port
[   22.223834] ata2: EH pending after completion, repeating EH (cnt=4)
[   22.223861] ata2: soft resetting port
[   22.300936] ata1.00: configured for UDMA/100
[   22.300956] ata1: EH pending after completion, repeating EH (cnt=4)
[   22.300978] ata1: soft resetting port
[   22.385774] ata2: EH complete
[   22.419051] ata2: soft resetting port
[   22.483212] ata1.00: configured for UDMA/100
[   22.483231] ata1: EH pending after completion, repeating EH (cnt=3)
[   22.483253] ata1: soft resetting port
[   22.580650] ata2: EH pending after completion, repeating EH (cnt=4)
[   22.580667] ata2: soft resetting port
[   22.665172] ata1.00: configured for UDMA/100
[   22.665181] ata1: EH complete
[   22.696334] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[   22.696390] sd 0:0:0:0: [sda] Write Protect is off
[   22.696399] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   22.696441] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.696490] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[   22.696514] sd 0:0:0:0: [sda] Write Protect is off
[   22.696522] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   22.696560] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.741632] ata2: EH complete
[   23.651406] ata2: soft resetting port
[   23.813188] ata2: EH pending after completion, repeating EH (cnt=4)
[   23.813214] ata2: soft resetting port
[   23.975152] ata2: EH complete
[   24.038303] ata2: soft resetting port
[   24.200020] ata2: EH pending after completion, repeating EH (cnt=4)
[   24.200045] ata2: soft resetting port
[   24.361214] ata2: EH complete
[   25.085864] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[   25.086035] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[   25.086388] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
[   25.093974] eth0: VIA Rhine II at 0x1c800, 00:40:63:e8:fc:57, IRQ 10.
[   25.094936] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
[   25.112426] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[   25.328316] Linux video capture interface: v2.00
[   25.497290] saa7146: register extension 'Multimedia eXtension Board'.
[   25.580945] saa7146: register extension 'hexium HV-PCI6 Orion'.
[   25.662330] saa7146: register extension 'hexium gemini'.
[   25.848423] powernow: This module only works with AMD K7 CPUs
[   25.861590] saa7146: register extension 'dvb'.
[   25.862171] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[   25.862359] saa7146: found saa7146 @ mem dcc9a000 (revision 1, irq 11) (0x13c2,0x000a).
[   26.011079] DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-CA rev1.X)
[   26.029670] adapter has MAC addr = 00:d0:5c:04:b0:57
[   26.435356] dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f12623
[   26.435373] dvb-ttpci: firmware @ card 0 supports CI link layer interface
[   26.541542] dvb-ttpci: DVB-C analog module @ card 0 detected, initializing MSP3415
[   26.645267] dvb_ttpci: saa7113 not accessible.
[   26.675976] saa7146_vv: saa7146 (0): registered device video0 [v4l2]
[   26.681285] saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
[   26.791706] DVB: registering frontend 0 (ST STV0297 DVB-C)...
[   26.792428] input: DVB on-card IR receiver as /class/input/input3
[   26.792454] dvb-ttpci: found av7110-0.
[   26.838385] saa7146: register extension 'dpc7146 demonstration board'.
[   26.899063] saa7146: register extension 'budget_ci dvb'.
[   26.930741] saa7146: register extension 'budget_av'.
[   26.959621] saa7146: register extension 'budget dvb'.
[   27.408015] dib0700: loaded with support for 6 different device-types
[   27.413607] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
[   27.414061] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[   27.419134] DVB: registering new adapter (Hauppauge Nova-T Stick)
[   27.750946] DVB: registering frontend 1 (DiBcom 7000PC)...
[   27.795064] MT2060: successfully identified (IF1 = 1220)
[   28.271363] input: IR-receiver inside an USB DVB receiver as /class/input/input4
[   28.271384] dvb-usb: schedule remote query interval to 150 msecs.
[   28.271395] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.
[   28.271882] dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.
[   28.276735] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[   28.277188] DVB: registering new adapter (Hauppauge Nova-T Stick)
[   28.612467] DVB: registering frontend 2 (DiBcom 7000PC)...
[   28.616983] MT2060: successfully identified (IF1 = 1220)
[   29.093024] input: IR-receiver inside an USB DVB receiver as /class/input/input5
[   29.093046] dvb-usb: schedule remote query interval to 150 msecs.
[   29.093057] dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.
[   29.093416] usbcore: registered new interface driver dvb_usb_dib0700
[   29.517733] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[   29.517926] PCI: VIA VLink IRQ fixup for 0000:00:11.5, from 5 to 11
[   29.518202] PCI: Setting latency timer of device 0000:00:11.5 to 64
[   30.267135] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   30.510916] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   30.585999] lirc_dev: IR Remote Control driver registered, major 61
[   30.588431] lirc_serial: no version for "lirc_unregister_plugin" found: kernel tainted.
[   31.099604] lirc_serial: auto-detected active low receiver
[   31.099769] lirc_dev: lirc_register_plugin: sample_rate: 0
[   67.581269] spurious 8259A interrupt: IRQ7.