uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 17, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 17, io base 0x0000e100
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 17, io base 0x0000e200
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 17, io base 0x0000e300
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 17
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 17, io mem 0xf6000000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 18
eth0: VIA Rhine II at 0xf6001000, 00:19:db:c6:b5:95, IRQ 18.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ip_tables: (C) 2000-2006 Netfilter Core Team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
usb 5-4: new high speed USB device using ehci_hcd and address 2
usb 5-4: configuration #1 chosen from 1 choice
dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-wt220u-fc03.fw'
usbcore: registered new interface driver dvb_usb_dtt200u
usb 5-4: USB disconnect, address 2
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 5-4: new high speed USB device using ehci_hcd and address 3
usb 5-4: configuration #1 chosen from 1 choice
dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in warm state.
dvb-usb: will use the device's hardware PID filter (table count: 15).
DVB: registering new adapter (WideView WT-220U PenType Receiver (Typhoon/Freecom))
DVB: registering frontend 0 (WideView USB DVB-T)...
input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:10.4/usb5/5-4/input/input3
dvb-usb: schedule remote query interval to 300 msecs.
dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) successfully initialized and connected.
dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in warm state.
dvb-usb: will use the device's hardware PID filter (table count: 15).
DVB: registering new adapter (WideView WT-220U PenType Receiver (Typhoon/Freecom))
DVB: registering frontend 1 (WideView USB DVB-T)...
input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:10.4/usb5/5-4/input/input4
dvb-usb: schedule remote query interval to 300 msecs.
dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) successfully initialized and connected.
dvb-usb: recv bulk message failed: -110
dvb-usb: recv we made it: 0 (<- von mir hinzugefügte dbg msg in dvb-usb-urb.c)
last message repeated 201 times
last message repeated 793 times
last message repeated 798 times
last message repeated 791 times
last message repeated 524 times
last message repeated 521 times
last message repeated 670 times
last message repeated 701 times
last message repeated 717 times
dvb-usb: recv bulk message failed: -110 (<- kurz nach vdr start:)
last message repeated 32 times
last message repeated 62 times
last message repeated 61 times
last message repeated 61 times
last message repeated 62 times
last message repeated 62 times
last message repeated 61 times
last message repeated 61 times
usw, sprich knapp mehr als 1x pro Sekunde diese Fehlermeldung