us speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Switched to high resolution mode on CPU 0
hda: ST3320620A, ATA DISK drive
hda: selected mode 0x45
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PIONEER DVD-RW DVR-106D, ATAPI CD/DVD-ROM drive
hdc: selected mode 0x42
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 625142448 sectors (320072 MB) w/16384KiB Cache, CHS=38913/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x0001d400 ctl 0x0001d002 bmdma 0x0001c400 irq 18
ata2: SATA max UDMA/133 cmd 0x0001cc00 ctl 0x0001c802 bmdma 0x0001c408 irq 18
ata2.00: ATA-7: ST3500630AS, 3.AAC, max UDMA/133
ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      ST3500630AS      3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 < sda5 >
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SAS Host driver 3.04.04
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.5 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath emc: version 0.0.3 loaded
EISA: Probing bus 0 at eisa.0
EISA: Detected 0 cards.
TCP cubic registered
Using IPI Shortcut mode
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 416k freed
NET: Registered protocol family 1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
snd_page_alloc: no version for "struct_module" found: kernel tainted.
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
input: PC Speaker as /class/input/input2
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ec00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xf7fffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 22
skge 1.11 addr 0xf7ef8000 irq 22 chip Yukon rev 1
skge eth0: addr 00:0a:5e:65:bc:b7
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 50751 usecs
intel8x0: clocking to 48000
usb 2-1: device not accepting address 2, error -71
Linux video capture interface: v2.00
v4l2_int_device: module license 'unspecified' taints kernel.
Linux video codec intermediate layer: v0.2
usb 2-1: new low speed USB device using uhci_hcd and address 4
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
saa7130/34: v4l2 driver version 0.2.14 loaded
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 21 (level, low) -> IRQ 21
saa7146: found saa7146 @ mem f922ec00 (revision 1, irq 21) (0x13c2,0x000e).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.3)
usb 2-1: configuration #1 chosen from 1 choice
adapter has MAC addr = 00:d0:5c:24:0c:04
saa7146: register extension 'budget dvb'.
saa7146: register extension 'budget_av'.
saa7146: register extension 'budget_ci dvb'.
saa7146: register extension 'budget_patch dvb'.
usb 2-2: new low speed USB device using uhci_hcd and address 5
bt878: AUDIO driver version 0.0.0 loaded
cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f12623
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: Crystal audio DAC @ card 0 detected
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
usb 2-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver b2c2_flexcop_usb
usbcore: registered new interface driver hiddev
input: Compaq Compaq Internet Keyboard as /class/input/input3
input: USB HID v1.00 Keyboard [Compaq Compaq Internet Keyboard] on usb-0000:00:1d.1-1
Marvell M88ALP01 'CAFE' Camera Controller version 2
input: Compaq Compaq Internet Keyboard as /class/input/input4
input,hiddev0: USB HID v1.00 Device [Compaq Compaq Internet Keyboard] on usb-0000:00:1d.1-1
Colour QuickCam for Video4Linux v0.05
input: 2.4G USB RF KeyBoard as /class/input/input5
input: USB HID v1.10 Keyboard [2.4G USB RF KeyBoard] on usb-0000:00:1d.1-2
input: 2.4G USB RF KeyBoard as /class/input/input6
input: USB HID v1.10 Mouse [2.4G USB RF KeyBoard] on usb-0000:00:1d.1-2
V4L-Driver for Vision CPiA based cameras v1.2.3
Since in-kernel colorspace conversion is not allowed, it is disabled by default now. Users should fix the applications in case they don't work without conversion reenabled by setting the 'colorspace_conv' module parameter to 1
input: 2.4G USB RF KeyBoard as /class/input/input7
input,hiddev1: USB HID v1.10 Device [2.4G USB RF KeyBoard] on usb-0000:00:1d.1-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
usbcore: registered new interface driver cinergyT2
DVB: registering frontend 0 (ST STV0299 DVB-S)...
input: DVB on-card IR receiver as /class/input/input8
dvb-ttpci: found av7110-0.
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 23 (level, low) -> IRQ 19
cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37,autodetected]
cx88[0]: TV tuner type 4, Radio tuner type -1
USB driver for Vision CPiA based cameras v1.2.3
usbcore: registered new interface driver cpia
cpia2: V4L-Driver for Vision CPiA2 based cameras v2.0.0
usbcore: registered new interface driver cpia2
Parallel port driver for Vision CPiA based cameras v1.2.3
saa7146: register extension 'dpc7146 demonstration board'.
saa7146: register extension 'hexium gemini'.
usbcore: registered new interface driver dabusb
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/dabusb.c: v1.54:DAB-USB Interface Driver for Linux (c)1999
em28xx v4l2 driver version 0.0.1 loaded
usbcore: registered new interface driver em28xx
et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1:1.09
usbcore: registered new interface driver et61x251
saa7146: register extension 'hexium HV-PCI6 Orion'.
ivtv:  Start initialization, version 1.1.0
saa7146: register extension 'Multimedia eXtension Board'.
usbcore: registered new interface driver ov511
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
OmniVision ov7670 sensor driver, at your service
ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C driver
Mediavision Pro Movie Studio driver 0.02
PMS type is 0
Board not found.
usbcore: registered new interface driver pvrusb2
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/pvrusb2-main.c: Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner : V4L in-tree version
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/pvrusb2-main.c: Debug mask is 15 (0xf)
tveeprom 2-0050: Hauppauge model 92001, rev C1B1, serial# 2878365
tveeprom 2-0050: MAC address is 00-0D-FE-2B-EB-9D
tveeprom 2-0050: tuner model is Conexant_CX24109 (idx 111, type 4)
tveeprom 2-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 2-0050: audio processor is CX883 (idx 32)
tveeprom 2-0050: decoder processor is CX883 (idx 22)
tveeprom 2-0050: has no radio, has IR receiver, has no IR transmitter
cx88[0]: hauppauge eeprom: model=92001
input: cx88 IR (Hauppauge Nova-S-Plus  as /class/input/input9
cx88[0]/0: found at 0000:02:02.0, rev: 5, irq: 19, latency: 128, mmio: 0xf3000000
cx88[0]/0: registered device video1 [v4l2]
cx88[0]/0: registered device vbi1
cx88[0]/2: cx2388x 8802 Driver Manager
ACPI: PCI Interrupt 0000:02:02.2[A] -> GSI 23 (level, low) -> IRQ 19
cx88[0]/2: found at 0000:02:02.2, rev: 5, irq: 19, latency: 128, mmio: 0xf5000000
ivtv:  End initialization
pwc: Philips webcam module version 10.0.13 loaded.
SAA5246A (or compatible) Teletext decoder driver version 1.8
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37]
cx88[0]/2: cx2388x based DVB/ATSC card
DVB: registering new adapter (cx88[0])
DVB: registering frontend 1 (Conexant CX24123/CX24109)...
ivtv-fb:  no cards found<6>pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
pwc: Trace options: 0x0001
usbcore: registered new interface driver Philips webcam
SAA5249 driver (SAA5249 interface) for VideoText version 1.8
cx2388x blackbird driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: blackbird access: shared
cx88[0]/2: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37]
cx88[0]/2: cx8802 probe failed, err = -19
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/se401.c: SE401 usb camera driver version 0.24 registering
usbcore: registered new interface driver se401
sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.47
usbcore: registered new interface driver sn9c102
usbcore: registered new interface driver stv680
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/stv680.c: [usb_stv680_init:1553] STV(i): usb camera driver version v0.25 registering
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/stv680.c: STV0680 USB Camera Driver v0.25
videodev: "vivi" has no release callback. Please fix your driver for proper sysfs support, see http://lwn.net/Articles/36850/
Video Technology Magazine Virtual Video Capture Board (Load status: 0)
w9968cf: V4L driver for W996[87]CF JPEG USB Dual Mode Camera Chip 1:1.33-basic
usbcore: registered new interface driver w9968cf
Zoran MJPEG board driver version 0.9.5
No known MJPEG cards found.
usbcore: registered new interface driver zr364xx
/usr/local/src/v4l-dvb-7386e449ad9c/v4l/zr364xx.c: Zoran 364xx module loaded
zc0301: V4L2 driver for ZC0301[P] Image Processor and Control Chip v1:1.10
usbcore: registered new interface driver zc0301
EXT3 FS on hda3, internal journal
EXT3-fs: Unrecognized mount option "0" or missing value
hda: selected mode 0x45
hdc: selected mode 0x42
EXT3-fs: Unrecognized mount option "0" or missing value
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
Adding 265032k swap on /dev/hda1.  Priority:-1 extents:1 across:265032k
usbcore: registered new interface driver libusual
skge eth0: enabling interface
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
NET: Registered protocol family 17
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
skge eth0: Link is up at 1000 Mbps, full duplex, flow control both
vivi: open called (minor=2)
usbcore: registered new interface driver kbtab
drivers/input/tablet/kbtab.c: v0.0.2:USB KB Gear JamStudio Tablet driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions