linvdr:~# dmesg
 machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon(tm) XP  2000+ stepping 00
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Core revision 20060707
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16) *10
ACPI: PCI Interrupt Link [LNKB] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 18) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 19) *11
ACPI: PCI Interrupt Link [LNKE] (IRQs 16) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *7
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 23) *10
ACPI: PCI Interrupt Link [LFWR] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LETH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:07: ioport range 0x480-0x487 has been reserved
pnp: 00:07: ioport range 0xd00-0xd07 has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: d000-dfff
  MEM window: fb900000-fc0fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: fc100000-fe2fffff
  PREFETCH window: eb600000-f37fffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/W].
JFS: nTxBlock = 7067, nTxLock = 56539
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
vesafb: framebuffer at 0xec000000, mapped to 0xf8c80000, using 1875k, total 32768k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG SP1614N, ATA DISK drive
hdb: ST380011A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1
hdb: max request size: 512KiB
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hdb: cache flushes supported
 hdb:
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
usbmon: debugfs is not available
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Time: tsc clocksource has been installed.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 192k freed
EXT3 FS on hda1, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdb, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
cdfs 2.6.19 loaded.
USB Universal Host Controller Interface driver v3.0
Adding 262136k swap on /var/vm/swapfile.  Priority:-1 extents:67 across:266604k
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKC] -> GSI 18 (level, high) -> IRQ 16
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:01:08.0: 3Com PCI 3c905B Cyclone 100baseTx at f8c48000.
eth0:  setting full-duplex.
Linux video capture interface: v2.00
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNKA] -> GSI 16 (level, high) -> IRQ 17
saa7146: found saa7146 @ mem f8ed8000 (revision 1, irq 17) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X)
adapter has MAC addr = 00:d0:5c:21:25:bc
dvb-ttpci: gpioirq unknown debitype 0 len 0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 8000261d
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
DVB: registering frontend 0 (ST STV0299 DVB-S)...
input: DVB on-card IR receiver as /class/input/input2
dvb-ttpci: found av7110-0.
saa7146: register extension 'budget dvb'.
saa7146: register extension 'budget_ci dvb'.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKD] -> GSI 19 (level, high) -> IRQ 18
saa7146: found saa7146 @ mem f8ef4000 (revision 1, irq 18) (0x13c2,0x100f).
saa7146 (1): dma buffer size 192512
DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI PCI)
adapter has MAC addr = 00:d0:5c:04:37:7c
input: Budget-CI dvb ir receiver saa7146 (1) as /class/input/input3
DVB: registering frontend 1 (ST STV0299 DVB-S)...
saa7146: register extension 'budget_av'.