Hm, da tut sich offenbar nichts mehr, oder? 
Posts by patrickl
-
-
Hallo Forum
bislang funktionierte mein 'TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device' bestens unter Debian Lenny. Gestern habe ich auf Squeeze geupdated und es geht nicht mehr. Auch in diversen Foren etc. konnte ich keine Lösung finden. Zu den Details:
dmesg meldet:
Code
Display More[ 5.926084] dvb-usb: found a 'TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device' in cold state, will try to load a firmware [ 5.926098] usb 3-2: firmware: requesting dvb-usb-dibusb-5.0.0.11.fw [ 6.304918] dvb-usb: downloading firmware from file 'dvb-usb-dibusb-5.0.0.11.fw' [ 9.136090] usb 3-2: new full speed USB device using uhci_hcd and address 3 [ 9.319184] usb 3-2: New USB device found, idVendor=1822, idProduct=3202 [ 9.319194] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 9.319200] usb 3-2: Product: VP7041[ 9.319204] usb 3-2: Manufacturer: TwinHan [ 9.319450] usb 3-2: configuration #1 chosen from 1 choice [ 9.322354] dvb-usb: found a 'TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device' in warm state. [ 9.340327] dvb-usb: will use the device's hardware PID filter (table count: 16). [ 9.342278] DVB: registering new adapter (TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device [ 9.469143] DVB: registering adapter 0 frontend 0 (DiBcom 3000M-B DVB-T)... [ 9.473131] dibusb: This device has the Thomson Cable onboard. Which is default. [ 9.494439] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:10.1/usb3/3-2/input/input5 [ 9.494641] dvb-usb: schedule remote query interval to 150 msecs. [ 9.508045] dvb-usb: TwinhanDTV USB-Ter USB1.1 / Magic Box I / HAMA USB1.1 DVB-T device successfully initialized and connected.Soweit sieht alles ja noch sehr gut aus (und auch so, wie ich es unter Lenny kannte).
lsusb liefert auch:
CodeBus 003 Device 003: ID 1822:3202 Twinhan VisionDTV USB-Ter/HAMA USB DVB-T device warmAllerdings kann ich weder mit dvbsnoop, nach tzap noch mencoder noch sonst was ein tuning hinbekommen
dvbsnoop -s signal:
Codecycle: 358 d_time: 0.022 s Sig: 0 SNR: 0 BER: 0 UBLK: 0 Stat: 0x00 []tzap:
Codestatus 00 | signal 0000 | snr 0000 | ber 001fffff | unc 0000ffff |mencoder:
Code
Display MoreOPEN_DVB: prog=ZDF, card=1, type=2 dvb_streaming_start(PROG: ZDF, CARD: 1, FILE: (null)) PROGRAM NUMBER 25: name=ZDF, freq=514000000 DVB_OPEN_DEVICES(3) OPEN(0), file /dev/dvb/adapter0/demux0: FD=4, CNT=0 OPEN(1), file /dev/dvb/adapter0/demux0: FD=5, CNT=1 OPEN(2), file /dev/dvb/adapter0/demux0: FD=6, CNT=2 DVB_SET_CHANNEL: new channel name=ZDF, card: 0, channel 25 dvb_tune Freq: 514000000 TUNE_IT, fd_frontend 3, fd_sec -1 freq 514000000, srate 0, pol Using DVB card "DiBcom 3000M-B DVB-T" tuning DVB-T to 514000000 Hz, bandwidth: 0 Getting frontend status Not able to lock to the signal on the given frequency, timeout: 30 dvb_tune, TUNING FAILED ERROR, COULDN'T SET CHANNEL 25: DVBIN_CLOSE, close(2), fd=6, COUNT=2 DVBIN_CLOSE, close(1), fd=5, COUNT=1 DVBIN_CLOSE, close(0), fd=4, COUNT=0 Failed to open dvb://ZDF. Cannot open file/device.Module sind auch alle da (lsmod):
Codedvb_usb_dibusb_common 4430 1 dvb_usb_dibusb_mb dib3000mc 8536 1 dvb_usb_dibusb_common dibx000_common 2025 1 dib3000mc dvb_usb 10632 2 dvb_usb_dibusb_mb,dvb_usb_dibusb_common dvb_core 62650 1 dvb_usbWie gesagt: unter Lenny lief bis gestern alles bestens, die Hardware/Antennenausrichtung/etc. passt also. Die Recht von /dev/dvb stimmen auch...
Hat jemand eine Idee?
Danke und Gruß,
Patrick