Beiträge von hondansx

  • Technotrend FF1.5 defekt? Tuner o.k - OSD grieselig

    Bei meiner Technotrend FF1.5 fliegen öfters Streifen übers Fernsehbild
    oder aber das OSD ist nur noch komplett grieselig.
    Der Tuner scheint zu gehen, da Aufnahmen bzw. das TVBild zu empfangen ist.
    Da hier im Forum einige Leute sind die sich mit sowas auskennen, wäre es toll
    wenn mir jemand einen Tip geben könnte.


    Danke
    Alex

  • [vdr] [ANNOUNCE] VDR developer version 1.5.2

    VDR developer version 1.5.2 is now available at


    ftp://ftp.cadsoft.de/vdr/Developer/vdr-1.5.2.tar.bz2


    A 'diff' against the previous developer version is available at


    ftp://ftp.cadsoft.de/vdr/Developer/vdr-1.5.1-1.5.2.diff



    I haven't had time to work on VDR in the past few weeks, so several
    bugfixes etc. that have been posted on the mailing list are still in
    my inbox and I have yet to look into them. I just wanted to get this
    version out now, because it implements a very first step into using
    UTF-8 character encoding. If you're using a language that has many
    non-7bit-ASCII characters, you may not want to use this version.
    However, if your language uses only a few such characters (like German),
    running this version on a UTF-8 system should at least get the file
    names of recordings right - even though the umlauts will not be
    displayed correctly on the OSD).



    WARNING:
    ========


    This is a *developer* version. Even though *I* use it in my productive
    environment, I strongly recommend that you only use it under controlled
    conditions and for testing and debugging.



    The changes since version 1.5.1:


    - Updated the Finnish OSD texts (thanks to Rolf Ahrenberg).
    - Fixed handling user activity for shutdown, which I had messed when adopting Udo's
    original patch (thanks to Udo Richter).
    - Added Turkish language texts (thanks to Oktay Yolgeçen).
    - Added missing rules for generating iso8859-13 font to Makefile.
    - 'libsi' now converts the incoming strings into the system's character set
    according to the DVB standard. The system's character set is determined from
    the LANG environment variable. If no recognizable setting can be found, no
    conversion will take place. Note that currently only the strings received from the
    SI data stream are converted, there have not been any changes regarding displaying
    UTF-8 characters on the OSD, yet - this will follow in one of the next steps.
    With this conversion, it should now be safe to run VDR on a UTF-8 file system,
    because all incoming characters are converted to UTF-8. This will most likely
    result in wrong characters being displayed on the OSD (because there UTF-8 is
    not known, yet), but the file names should be ok (haven't tested this myself,
    though, because I don't do UTF-8 - so please be very careful when testing!).
    There's one piece of bad news here: the German pay-tv broadcaster Premiere
    apparently encodes all EPG strings as ISO8859-1, but fails to correctly mark
    these strings as such. Therefore 'libsi' (following the DVB standard) considers
    the strings to be encoded in the default ISO6937 and converts them to whatever
    the system's character set is. This, of course, results in wrong umlauts.
    On its old transponder, the ProSieben/SAT.1 channels also had their EPG data
    wrongly encoded, but apparently on the new transponder they started broadcasting
    on this month, they got it right.


    Have fun!


    Klaus

  • Cinergy 1200 DVB-C wird nicht erkannt

    Zitat

    Wenn Du uns noch verraten würdest, welche Karte Du hast (Subsystem-Id), könnte man damit evtl. etwas anfangen... schiel
    Falls es 'ne alte war: Hat es mit dem ungepatchten Treiber funktioniert?


    Ich habe eine nagelneue Terratec 1200 mit diesem Patch tda1002x.007.diff getestet.


    0000:00:08.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
    Subsystem: TERRATEC Electronic GmbH: Unknown device 1176
    Flags: bus master, medium devsel, latency 32, IRQ 10
    Memory at e0400000 (32-bit, non-prefetchable) [size=512]


    saa7146: register extension 'budget_av'.
    ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
    saa7146: found saa7146 @ mem d09cc000 (revision 1, irq 10) (0x153b,0x1176).
    saa7146 (1): dma buffer size 192512
    DVB: registering new adapter (Terratec Cinergy 1200 DVB-C MK3).
    adapter failed MAC signature check
    encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff
    KNC1-1: MAC addr = 00:0a:ac:11:08:4d
    DVB: registering frontend 1 (Philips TDA10023 DVB-C)...
    budget-av: ci interface initialised.


    Wie kann ich die Subsystem-Id ermitteln?


    Bye Alex

  • [ANNOUNCE] VDR maintenance patch 1.4.5-1

    VDR maintenance patch 1.4.5-1 is now available at


    ftp://ftp.cadsoft.de/vdr/Developer/vdr-1.4.5-1.diff


    This is a 'diff' against version 1.4.5.



    Small fixes to the officially released VDR versions will be first
    made available as "maintenance patches" in the Developer directory,
    so that they can be reviewed and tested before a new official
    release is published.


    So please apply the above patch and report whether it works (or
    if it causes any new problems).



    This version is binary compatible to the previous one, so plugins
    don't need to be recompiled.



    The changes since version 1.4.5:


    - Fixed i18n characters for the Hungarian texts (thanks to Thomas Günther).
    - Now using cPipe instead of popen() in cCommand::Execute() to avoid problems
    with open file handles when starting background commands (thanks to Reinhard
    Nissl).


    Have fun!


    Klaus

  • DVB-C Qualität - QAM 256

    Anscheinend ist es bekannt, das Kabeldeutschland was in Ihrem System umgestellt hat.
    Die Umstellung ging bis 08.12.06.
    Nachbesserungen sollten bis Anfang Januar einfliesen. Danach sollte sich nichts mehr ändern.


    Das gibt Grund zu Hoffnung.



    Gruss Alex

  • DVB-C Qualität - QAM 256

    So wie ich das verstehe, würde das bedeuten, das ich im Treiber alle Frequenzen 500000 Herz
    nach unten korrigieren muss und das für jeden Kanal?


    Hört sich nach einer Fleissarbeit an und es nicht gewährleistet das die nicht wieder was in kurzer Zeit ändern.


    Ist das nun ein generelles Treiberproblem, weil nicht nachjustiert wird ,oder liegt es an Kabeldeutschland?



    Gruss Alex