tevii s660 und atric einschalter

hallo,

habe ein problem mit tevii s 660 und atric einschalter,

da die s660 internen ir empfänger hat blockt die mir den atric enschalter, weiss jemand wie ich das ändern kann, damit lirc nur mit atric läuft ?

ls -l /dev/lirc*
crw-rw---- 1 root root 61, 0 2010-01-26 11:02 /dev/lirc0
lrwxrwxrwx 1 root root 19 2010-01-26 11:02 /dev/lircd -> /var/run/lirc/lircd

ausgabe von lsmod :

Module Size Used by
lirc_serial 9910 1
lirc_dev 8780 3 lirc_serial
snd_hda_codec_nvhdmi 3714 1
snd_hda_codec_realtek 200623 1
snd_hda_intel 21050 2
snd_hda_codec 72523 3 snd_hda_codec_nvhdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 5244 1 snd_hda_codec
snd_pcm_oss 34472 0
snd_mixer_oss 14152 1 snd_pcm_oss
snd_pcm 69078 4 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1298 0
snd_seq_oss 26047 0
ds3000 13608 1
snd_seq_midi 4429 0
snd_rawmidi 18604 1 snd_seq_midi
snd_seq_midi_event 5771 2 snd_seq_oss,snd_seq_midi
nvidia 8874927 44
snd_seq 45793 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
lp 6964 0
snd_timer 19133 2 snd_pcm,snd_seq
i2c_nforce2 5159 0
snd_seq_device 5500 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
agpgart 31015 1 nvidia
teviis660 6718 10
shpchp 28236 0
snd 53200 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
dvb_usb 13982 1 teviis660
psmouse 60792 0
soundcore 6428 1 snd
parport 32027 1 lp
dvb_core 84883 1 dvb_usb
serio_raw 3812 0
snd_page_alloc 7204 2 snd_hda_intel,snd_pcm
usbhid 35328 0
r8169 33423 0
mii 4245 1 r8169

wenn ich umschalte mit tastatur auf xbmc, dann klappt die fernbedienung.

wenn die tevii ausgesteckt ist , klappts auch.

Bei mir läuft freeVDR 2.1

dmesg gibt folgendes aus :

[ 8.885109] dvb-usb: found a 'TEVII S660 DVBS2 USB2.0' in warm state.
[ 8.885267] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 8.885565] DVB: registering new adapter (TEVII S660 DVBS2 USB2.0)
[ 9.014585] dvb-usb: MAC address: 00:18:bd:5c:56:a8
[ 9.114696] r8169: eth0: link down
[ 9.114731] r8169: eth0: link down
[ 9.115153] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.296191] DS3000 chip version: 0.192 attached.
[ 9.296199] S660: DS3000 attached.
[ 9.296208] DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)...
[ 9.296823] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:06.1/usb2/2-3/input/input5
[ 9.296908] dvb-usb: schedule remote query interval to 150 msecs.
[ 9.296917] dvb-usb: TEVII S660 DVBS2 USB2.0 successfully initialized and connected.
[ 9.296960] usbcore: registered new interface driver teviis660
[ 9.734212] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[ 9.735234] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
[ 9.735247] HDA Intel 0000:00:08.0: PCI INT A -> Link[LAZA] -> GSI 23 (level, low) -> IRQ 23
[ 9.735316] HDA Intel 0000:00:08.0: setting latency timer to 64
[ 10.545037] hda_codec: ALC662 rev1: BIOS auto-probing.
[ 10.860235] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:08.0/input/input6
[ 12.299549] lirc_dev: IR Remote Control driver registered, major 61
[ 13.204031] lirc_serial: auto-detected active low receiver
[ 13.204041] lirc_dev: lirc_register_driver: sample_rate: 0
[ 13.204328] lirc_serial $Revision: 5.104 $ registered

eigentlich nicht , ist nicht in sicht mit lcd