Hallo Gemeinde, Beim VDR aufsetzen (Mlz ISO3.2)kann man ja im setup ins
Netz gehen um zB.für das Wetterplugin oder für die Fernbedinungen. Bei mir
kommt aber keine Verbindung zustande. Vorhandene Harware VDR mit Asrock
Board Netzwerkkarte on Board und Fritzbox 7050. Die IP,s im VDR hab ich auch
vergeben, wer hatt nen Tip.
VDR miit Fritzbox
- mischga
- Geschlossen
-
-
Vermutlich meinst Du die Namensauflösung (/etc/resolv.conf),
bist im im setup Programm direkt oder über putty.Falls Du meinst das sie Ips die Du lokal eingetragen hast in Ordnung sind aber kein Kontakt zum anderen PC besteht
(auch nicht über IP [ping etc]) dann stimmt das ausgewählte Modul für die Netzwerkkarte vermutlich nicht.Fang mal mit folgenden Befehlen an.
was sagt:
und :
bzw. :
und welche Netzwerkkarte hast Du in dem Gerät -
Ich hab den VDR direckt per Patchkabel mit der Fritzbox verbunden die
wiederum ja mit dem Web verbunden ist, müßte ja reichen um die Daten aus dem Netz zu holen. Eingestellt habe ich alles auf 196.168.0.4 /255.255.255.0
Mit Putty u. WinSCP funzelt es ja.(PC auch an der Box) -
-
Zitat
Ich hab den VDR direckt per Patchkabel mit der Fritzbox verbunden die
wiederum ja mit dem Web verbunden ist, müßte ja reichen um die Daten aus dem Netz zu holen.
Bei DHCP ja - natürlich nur wenn DHCP auf dem Fritz Teil aktiv ist
manuell ist IP / Subnetz / Gateway / DNS zu konfigurieren -
Ich kann mich mienem Vorredner nur anschliessen: die Ausgaben von 'ifconfig' und 'route' wären trotzdem hilfreich. Was hast Du als DNS-Server mit angegeben?
-
wie komme ich zu der ifconfig, ist die in so ner logfile drinn ?
-
Einfach mit Putty einloggen, ifconfig eingeben und die Ausgabe hier posten.
-
login as: root
root@196.168.04's password:
Last login: Sun Jun 3 18:42:32 2007 from 196.168.0.1 on ttyp0
Last login: Sun Jun 3 18:42:32 2007 from 196.168.0.1
linvdr:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:13:8F:D4:28:60
inet addr:196.168.0.4 Bcast:196.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7243 errors:0 dropped:0 overruns:0 frame:0
TX packets:13505 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:664927 (649.3 KiB) TX bytes:10179521 (9.7 MiB)
Interrupt:201 Base address:0xd400lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:32 errors:0 dropped:0 overruns:0 frame:0
TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2688 (2.6 KiB) TX bytes:2688 (2.6 KiB)linvdr:~#
-
Und noch ,,Route"
login as: root
root@196.168.0.4's password:
Last login: Sun Jun 3 18:32:43 2007 from 196.168.0.1 on ttyp0
Last login: Sun Jun 3 18:32:43 2007 from 196.168.0.1
linvdr:~# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
196.168.0.0 * 255.255.255.0 U 0 0 0 eth0
default 196.168.0.4 0.0.0.0 UG 0 0 0 eth0
linvdr:~# login as: root
Password:
Last login: Sun Jun 3 18:32:43 2007 from 196.168.0.1 on ttyp0
Last login: Sun Jun 3 18:32:43 2007 from 196.168.0.1
linvdr:~# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
196.168.0.0 * 255.255.255.0 U 0 0 0 eth0
default 196.168.0.4 0.0.0.0 UG 0 0 0 eth0
linvdr:~#Login incorrect
linvdr login: Password:
Login incorrect
linvdr login: Password:
Login incorrect
linvdr:~# Destination Gateway Genmask Flags Metric Ref Use Iface
-bash: Destination: command not found
linvdr:~# 196.168.0.0 * 255.255.255.0 U 0 0 0 eth0
-bash: 196.168.0.0: command not found
linvdr:~# default 196.168.0.4 0.0.0.0 UG 0 0 0 eth0
-bash: default: command not found
linvdr:~# linvdr:~#
-bash: linvdr:~#: command not found
linvdr:~# -
Du hast als Gateway die Adresse des VDRs eingegeben. Starte noch einmal das setup von Linvdr und pass das an. Als Gateway muss die IP der Fritz Box angegeben werden.
Jetzt mitmachen!
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!