Hilfe bitte: Mahlzeit und kein USB

UKFencer · 15. März 2007

Tach,

habe gestern dieses Board+CPU bekommen:

http://www.fujitsu-siemens.co.…oards/FSC/d1520/D1520.htm

Zum ersten mal Mahlzeit ausprobiert und bin echt platt super einfache Installation und Konfiguration.

Nur leider habe ich kein USB (lsusb - NIX) und ich wollte doch WLan nutzen...was mache ich jetzt?

Gruß, UKFencer

Papsi · 15. März 2007

Gehe mal auf die Console(am besten von Putty aus) und nutze logread -f

Dann stecke den USB Wlan Stick mal ein und schau mal ob was passiert.
poste mal den Ausdruck, wenn was kommt.

evtl. mußt Du vorher noch mounten.

:EDIT
Und auch noch ein Eintrag in /etc/fstab

Gruß
Papsi

PS
Komische Kategorie hier

UKFencer · 15. März 2007

Code

00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 03)
00:02.0 VGA compatible controller: Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller  (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller  (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller  (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 02)
02:05.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (LOM) Ethernet Controller (rev 82)
02:09.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)

Alles anzeigen

Jetzt verstehe ich gar nichts mehr...

Papsi · 15. März 2007

Ich auch nicht, weil ich das nicht haben wollte.

Wollte einen Ausdruck von logread haben.
Siehe auch meinen 1. Beitrag wegen dem Edit

UKFencer · 15. März 2007

Ich weiss...hatte nur schon angefangen zu tippen

hier die /etc/fstab

Code

#
/dev/hdc1	  /		ext3	 defaults,errors=remount-ro	 0 1
# /dev/hda2	  none		swap	 sw				 0 0
/var/vm/swapfile  none		swap     sw                              0 0
/dev/dvd	 /mnt/dvd	auto	 ro,noauto,user,noexec 		 0 0
/dev/dvd         /mnt/cdfs      cdfs     ro,noauto,user,noexec           0 0
/dev/fd0         /mnt/floppy    auto     noauto,user,noexec              0 0
proc		 /proc		proc	 defaults                        0 0
devfs            /devfs		devfs    defaults                        0 0 
none             /proc/bus/usb  usbdevfs defaults                        0 0
sysfs            /sysfs         sysfs    defaults                        0 0

Alles anzeigen

logread -f läuft immer noch...ziemlich lahm. Was macht den -f?

Papsi · 15. März 2007

Das gibt die Ausgabe "live" aus.
Also das was gerade passiert.

Mache mal einen Neustart und lasse den Stick noch weg.
Dann mache eine Console auf und tippe logread -f ein

Erst dann steckst Du den Stick ein und dann muß was kommen.
Das postest Du dann hier.

Papsi · 15. März 2007

Und füge noch folgendes in deine fstab ein:

Code

usbfs                /proc/bus/usb        usbfs      noauto                0 0

Hast schon gemountet?

Code

mount usbfs

UKFencer · 15. März 2007

schau mal...

Code

Mar 15 23:10:51 linvdr auth.info sshd[1567]: Accepted password for root from 192.168.178.2 port 43041 ssh2
Mar 15 23:10:51 linvdr auth.info PAM_unix[1567]: (ssh) session opened for user root by (uid=0)
Mar 15 23:10:51 linvdr auth.err PAM-env[1567]: Unable to open config file: No such file or directory
Mar 15 23:10:51 linvdr auth.err PAM-env[1573]: Unable to open config file: No such file or directory
Mar 15 23:11:02 linvdr user.info vdr: [1445] connect from 127.0.0.1, port 2665 - accepted
Mar 15 23:11:02 linvdr user.info vdr: [1445] closing SVDRP connection
Mar 15 23:11:05 linvdr user.info kernel: usb 4-1: new high speed USB device using ehci_hcd and address 3
Mar 15 23:11:05 linvdr user.info kernel: usb 4-1: configuration #1 chosen from 1 choice
Mar 15 23:11:06 linvdr user.notice root: unknown device
Mar 15 23:11:06 linvdr user.notice root: added /proc/bus/usb/004/003
Mar 15 23:11:06 linvdr user.notice root: No SCSI host adapters found in sysfs

Alles anzeigen

mahlzeit · 15. März 2007

Servus,

mach mal ein "modprobe usb-storage" und guck mit "dmesg" mal die Ausgabe an. Steht dann dort was in der Art von /dev/sda?

UKFencer · 15. März 2007

Zitat

Original von mahlzeit
Servus,

mach mal ein "modprobe usb-storage" und guck mit "dmesg" mal die Ausgabe an. Steht dann dort was in der Art von /dev/sda?

Code

CI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
  IO window: 3000-3fff
  MEM window: d0100000-d01fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
Simple Boot Flag at 0x69 set to 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/W].
JFS: nTxBlock = 1925, nTxLock = 15404
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x2800-0x2807, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x2808-0x280f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HL-DT-ST CD-ROM GCR-8522B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SAMSUNG SV1604N, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 512KiB
hdc: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hdc: cache flushes supported
 hdc: hdc1 hdc2
hda: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.001.
3ware 9000 Storage Controller device driver for Linux v2.26.02.007.
libata version 2.00 loaded.
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
usbmon: debugfs is not available
PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Time: tsc clocksource has been installed.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 180k freed
input: AT Translated Set 2 keyboard as /class/input/input0
EXT3 FS on hdc1, internal journal
cdfs 2.6.17 loaded.
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 177, io base 0x00001000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 185, io base 0x00001400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 169, io base 0x00001800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 193, io mem 0xd0080000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-2: device not accepting address 2, error -71
usb 1-2: new low speed USB device using uhci_hcd and address 4
Adding 262136k swap on /var/vm/swapfile.  Priority:-1 extents:71 across:277496k
usb 1-2: configuration #1 chosen from 1 choice
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 20 (level, low) -> IRQ 201
e100: eth0: e100_probe: addr 0xd0100000, irq 201, MAC addr 00:30:05:4E:25:4E
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Linux video capture interface: v2.00
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 17 (level, low) -> IRQ 209
saa7146: found saa7146 @ mem d01ce000 (revision 1, irq 209) (0x13c2,0x0002).
DVB: registering new adapter (Technotrend/Hauppauge WinTV DVB-C rev2.X).
adapter has MAC addr = 00:d0:5c:20:f3:47
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80f22623
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
DVB: registering frontend 0 (VLSI VES1820 DVB-C)...
input: DVB on-card IR receiver as /class/input/input1
dvb-ttpci: found av7110-0.
saa7146: register extension 'budget dvb'.
saa7146: register extension 'budget_ci dvb'.
saa7146: register extension 'budget_av'.
ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 19 (level, low) -> IRQ 185
saa7146: found saa7146 @ mem d0282400 (revision 1, irq 185) (0x153b,0x1156).
saa7146 (1): dma buffer size 192512
DVB: registering new adapter (Terratec Cinergy 1200 DVB-C).
adapter failed MAC signature check
encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff
KNC1-1: MAC addr = 00:0a:ac:01:e4:9a
DVB: registering frontend 1 (Philips TDA10021 DVB-C)...
budget-av: ci interface initialised.
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
lirc_dev: IR Remote Control driver registered, at major 61 
lirc_serial: no version for "lirc_unregister_plugin" found: kernel tainted.
budget-av: cam inserted A
lirc_serial: auto-detected active high receiver
lirc_dev: lirc_register_plugin: sample_rate: 0
dvb_ca adapter 1: DVB CAM detected and initialised successfully
budget-av: cam inserted A
dvb_ca adapter 1: DVB CAM detected and initialised successfully
usb 4-1: new high speed USB device using ehci_hcd and address 3
usb 4-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.

Alles anzeigen

UKFencer · 15. März 2007

habe gerade mal Knoppix eingelegt und USB wird erkannt??

UKFencer · 15. März 2007

Zitat
Original von Papsi
Und füge noch folgendes in deine fstab ein:
Code
usbfs                /proc/bus/usb        usbfs      noauto                0 0
Hast schon gemountet?
Code
mount usbfs

command not found...war die Antwort

Papsi · 15. März 2007

bei was???

UKFencer · 15. März 2007

Zitat

Original von Papsi
bei was???

habe Deine Änderungen in der fstab eingetragen, gebooted und mount-Befehl. Doch leider ohne Erfolg.

Hilfe bitte: Mahlzeit und kein USB

Jetzt mitmachen!

Teilen