Activy 370(2xKabel, analog) - Installationsprobleme

Hi

lsmod[1]:
Module Size Used by
snd_pcm_oss 52768 0
snd_mixer_oss 17280 2 snd_pcm_oss
snd_seq_oss 31360 0
snd_seq_midi_event 7040 1 snd_seq_oss
snd_seq 51664 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 8716 2 snd_seq_oss,snd_seq
snd_intel8x0 30876 1
snd_ac97_codec 84256 1 snd_intel8x0
snd_ac97_bus 2432 1 snd_ac97_codec
snd_pcm 87304 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer 24452 2 snd_seq,snd_pcm
snd_page_alloc 10888 2 snd_intel8x0,snd_pcm
realmagic84xx 10396 2
msp3400 27936 0
saa7115 14224 0
tuner 55336 0
ivtv 168848 4
firmware_class 10240 1 ivtv
i2c_algo_bit 8584 1 ivtv
cx2341x 10244 1 ivtv
tveeprom 13968 1 ivtv
videodev 23552 5 ivtv
v4l1_compat 12548 2 ivtv,videodev
v4l2_common 20608 6 msp3400,saa7115,tuner,ivtv,cx2341x,videodev
e100 32644 0
natsemi 25312 0
i2c_i801 8460 0
i2c_dev 8964 0
i2c_core 20752 8 msp3400,saa7115,tuner,ivtv,i2c_algo_bit,tveeprom,i2c_i801,i2c_dev
usb_storage 61632 0
tsdev 7616 0

/_config/bin/dvbmod check:
/_config/bin/dvbmod check

/_config/bin/dvbmod load:
FATAL: Error inserting ivtv_fb (/lib/modules/2.6.16-gentoo/kernel/drivers/media/video/ivtv/ivtv-fb.ko): Operation not permitted

lsmod[2]:
Module Size Used by
snd_pcm_oss 52768 0
snd_mixer_oss 17280 2 snd_pcm_oss
snd_seq_oss 31360 0
snd_seq_midi_event 7040 1 snd_seq_oss
snd_seq 51664 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 8716 2 snd_seq_oss,snd_seq
snd_intel8x0 30876 1
snd_ac97_codec 84256 1 snd_intel8x0
snd_ac97_bus 2432 1 snd_ac97_codec
snd_pcm 87304 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer 24452 2 snd_seq,snd_pcm
snd_page_alloc 10888 2 snd_intel8x0,snd_pcm
realmagic84xx 10396 2
msp3400 27936 0
saa7115 14224 0
tuner 55336 0
ivtv 168848 4
firmware_class 10240 1 ivtv
i2c_algo_bit 8584 1 ivtv
cx2341x 10244 1 ivtv
tveeprom 13968 1 ivtv
videodev 23552 5 ivtv
v4l1_compat 12548 2 ivtv,videodev
v4l2_common 20608 6 msp3400,saa7115,tuner,ivtv,cx2341x,videodev
e100 32644 0
natsemi 25312 0
i2c_i801 8460 0
i2c_dev 8964 0
i2c_core 20752 8 msp3400,saa7115,tuner,ivtv,i2c_algo_bit,tveeprom,i2c_i801,i2c_dev
usb_storage 61632 0
tsdev 7616 0

dmesg | tail -n 10:
tuner 2-0061: tuner type not set
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 50757 usecs
intel8x0: clocking to 48000
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
tuner 2-0061: tuner type not set
tuner 2-0061: tuner type not set
tuner 2-0061: tuner type not set
ivtv-osd: Specified card (id 0) is either not present or does not support TV out

Ob das mit der SSH-Freigabe funktioniert kann ich nicht sagen.
Ich stelle den VDR mal bei meiner Firewall mal für nen Stündchen in die DMZ.
Meine IP-Adresse schicke ich dir gleich per Mail.

Hi. Das entfernen einer TV-Karte hat leider auch nichts bewirkt
JoeCool25: Bei dir hat es doch funktioniert, oder? Hast Du evtl noch einen Tipp?

Hi
Der andere Beitrag konnte mir leider nicht weiterhelfen.
Ich habe die obige Prozedur noch einmal mit nur einer TV-Karte nachgespielt.
Leider bekommen ich nur Schnee – Naja, das ist ja schon mal was
Nach 'modprobe' sagt
dmesg:
Linux version 2.6.16-gentoo (root@vdr01) (gcc version 3.3.4 20040623 (Gentoo Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #2 PREEMPT Tue Mar 21 20:01:15 CET 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ac00 (usable)
BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ca000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fef0000 (usable)
BIOS-e820: 000000000fef0000 - 000000000feff000 (ACPI data)
BIOS-e820: 000000000feff000 - 000000000ff00000 (ACPI NVS)
BIOS-e820: 000000000ff00000 - 0000000010000000 (usable)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
256MB LOWMEM available.
On node 0 totalpages: 65536
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 61440 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:0
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f86c0
ACPI: RSDT (v001 PTLTD RSDT 0x06040001 LTP 0x00000000) @ 0x0fefd1df
ACPI: FADT (v001 FSC D1636 0x06040001 0x000f4240) @ 0x0fefd20b
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040001 LTP 0x00000001) @ 0x0fefefd8
ACPI: DSDT (v001 FSC D1636 0x06040001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0xf008
Allocating PCI resources starting at 20000000 (gap: 10000000:efb80000)
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=2.6 ro root=302 video=vesafb:off
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1196.596 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254552k/262144k available (3043k kernel code, 6976k reserved, 1054k data, 160k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2395.29 BogoMIPS (lpj=1197648)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Celeron(TM) CPU 1200MHz stepping 04
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0e20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9a3, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region f000-f07f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region f180-f1bf claimed by ICH4 GPIO
Boot video device is 0000:01:06.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIH._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: f4000000-f5ffffff
PREFETCH window: f8000000-fbffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
Simple Boot Flag at 0x69 set to 0x1
Machine check exception polling timer started.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFS: nTxBlock = 1989, nTxLock = 15918
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i810 E chipset, but could not find the secondary device.
[drm] Initialized drm 1.0.1 20051102
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH: IDE controller at PCI slot 0000:00:1f.1
ICH: chipset revision 2
ICH: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1c00-0x1c07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1c08-0x1c0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
hda: ST3160023A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
input: PS/2 Logitech Mouse as /class/input/input1
hdc: _NEC DVD_RW ND-3500AG, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(66)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
usbmon: debugfs is not available
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 9, io base 0x00001000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC).
ALSA device list:
No soundcards found.
oprofile: using timer interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 PCIH USB AC97 KEYB PS2M COM1
ACPI: (supports S0 S1 S3 S4 S5)
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 160k freed
kjournald starting. Commit interval 5 seconds
ts: Compaq touchscreen protocol output
Adding 979956k swap on /dev/hda3. Priority:-1 extents:1 across:979956k
EXT3 FS on hda2, internal journal
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
e100: eth0: e100_probe: addr 0xf4004000, irq 9, MAC addr 00:30:05:88:82:DE
Linux video capture interface: v1.00
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.8.0 (v4l-dvb + ivtv virtual merge) Revision: 3311 loading
ivtv: Linux version: 2.6.16-gentoo preempt 586 gcc-3.3
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-250 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
tveeprom 1-0050: Hauppauge model 32599, rev D180, serial# 7157088
tveeprom 1-0050: tuner model is Philips FQ1216LME MK3 (idx 80, type 4)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
tveeprom 1-0050: audio processor is MSP4418 (idx 25)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has no radio, has no IR remote
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-A2 found @ 0x80 (ivtv i2c driver #0)
msp3400 1-0040: MSP4418G-A2 supports nicam and radio, mode is autodetect and autoselect
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 1-0061: tuner type not set
tuner 1-0061: tuner type not set
ivtv0: Initialized Hauppauge WinTV PVR-250, card #0
ivtv: ==================== END INIT IVTV ====================
ivtv-osd: Specified card (id 0) is either not present or does not support TV out
ivtv-osd: Specified card (id 0) is either not present or does not support TV out
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ivtv-osd: Specified card (id 0) is either not present or does not support TV out
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
em84xx: EM84xx 8400 (rev 1) bus: 1, devfn: 80, irq: 10,memory: 0xf4100000.
em84xx: mapped-memory at 0xd1b80000
quasar_dev_id: #33792
[Received irq data: 0000100c-0000100b-00008000]
[Received ring3 pid is 3477]
em84xx: dmaalloc called with 32768 (ok at c0520000)
em84xx: dmaalloc called with 32768 (ok at c0508000)
em84xx: dmaalloc called with 32768 (ok at c0568000)
em84xx: dmaalloc called with 32768 (ok at c0090000)
em84xx: dmaalloc called with 32768 (ok at c0008000)
em84xx: dmaalloc called with 32768 (ok at c0510000)
em84xx: dmaalloc called with 32768 (ok at c0518000)
em84xx: dmaalloc called with 32768 (ok at c0570000)
em84xx: dmaalloc called with 32768 (ok at c0578000)
em84xx: dmaalloc called with 32768 (ok at c0080000)
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 50022 usecs
intel8x0: clocking to 48000
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ACPI: PCI interrupt for device 0000:01:07.0 disabled
ivtv0: Removed Hauppauge WinTV PVR-250, card #0

./w_pvrscan:
S-Video 1;w_pvrscan:1:B6D12:P:0:301:300:305:A0:9001:0:0:0
Composite 1;w_pvrscan:1:B6D12:P:0:301:300:305:A0:9002:0:0:0
S-Video 2;w_pvrscan:1:B6D34:P:0:301:300:305:A0:9003:0:0:0
Composite 2;w_pvrscan:1:B6D23:P:0:301:300:305:A0:9004:0:0:0
Composite 3;w_pvrscan:1:B6D34:P:0:301:300:305:A0:9005:0:0:0
Found total 0 TV Stations.

Die 'Channels.conf' habe ich nach dem o.g. Vorschlag bei mir manuell bestückt.

Ich glaub ich muss aufgeben. Oder?
JoeCool25: Kannst du mir evtl. ein Image deiner Activy zukommen lassen?

Hallo JoeCool25

Wie versprochen habe es noch einmal genau nach deinen aktualisierten Anweisungen versucht.
Nachdem dieses nicht funktionierte habe ich zusätzlich noch
sh /_config/bin/dvb_update.sh
ausgeführt.
Jetzt hatte ich nachdem ich die Channels.conf angepasst hatte wenigstens schon mal wieder Schnee.

./w_pvrscan -p pvrinput >> /etc/vdr/channels.conf
gab danach folgendes aus:

w_pvrscan version 20060415
-_-_-_-_-_-_-Initializing TV card-_-_-_-_-_-_-_-_
Info: using IVTV adapter auto detection.
Info: Using ivtv device /dev/video0
Info: Card is Hauppauge WinTV PVR-150.
ERROR: IVTV_IOC_G_CODEC failed: Invalid argument

Beim ausführen von sh /_config/bin/dvb_update.sh bekam ich auch schon diese Fehlermeldung. Woran kann das liegen?