[gelöst] Streamdev - Prioritäten richtig setzen um LiveTv und Recordings zu bevorzugen

gggggg · 30. März 2021

Ein Script schaltet im Hintergrund mit wget über den streamdev-server die Kanäle durch ...

Nun ruckelt mein LiveTV . Das Alles läuft auf einem NUC10i3. Es sollte also keine Frage der Rechenleistung sein ...

Für einen Ruckeltest reicht einfach wget -T3 localhost:3000/TS/1

Im Plugin Readme habe ich Folgendes gelesen:

Zitat

Code

* Priorities:
-------------
(Affected: 0.5.x and older)

The server-side setting "Suspend behaviour" has been dropped in 0.6.0 in favour
of priority based precedence. A priority of 0 and above means that clients
have precedence. A negative priority gives precedence to local live TV on the
server. So if "Suspend behaviour" was previously set to "Client may suspend" or
"Never suspended", you will have to configure a negative priority. If the
"Suspend behaviour" was set to "Always suspended", the default values should do.

Configure the desired priorities for HTTP and IGMP Multicast streaming in the
settings of streamdev-server. If you haven't updated all your streamdev-clients
to at least 0.5.2, configure "Legacy Client Priority", too.

In streamdev-client, you should set "Minimum Priority" to -99. Adjust "Live TV
Priority" if necessary.

....
Precedence between multiple clients and between client and server is controlled
with priorities. For HTTP and IGMP Multicast, the priority is configured in
streamdev-server's setup menu. A negative priority gives precedence to local
live TV on the server. Zero and positive values give precedence to the client.

The priority for VDR clients watching live TV is configured in the plugin setup
of streamdev-client. For other client tasks (e.g. recording a client side timer)
the same priority as on the client is used. With the parameter "Legacy client
Priority" in streamdev-server's setup menu you can configure the priority for
clients which cannot be configured to use negative priorities. It is used
when an old client is detected an it requests priority "0".

On the server, the main menu entry "Streamdev Connections" gives you a list
of currently connected clients. Use the "red" key to terminate a connection.
Note that depending on connection type and client, the client might re-connect
sooner or later.

The "blue" key in the server's main menu will suspend live TV on server. An
image is displayed instead. This would allow a low priority client to switch
to a different transponder. Enable "Client may suspend" in the server setup
to allow VDR clients to suspend live TV remotely.

In the server's setup there's also an option to suspend live TV when starting
the server. The "auto" option will suspend live TV if there's no device with
an MPEG decoder available which is typically the case on a headless server.

NOTE: Precedence is mainly an issue on One-Card-Systems, since with multiple
cards there is no need to switch transponders on the primary interface, if one
of the other cards is idle (i.e. if it is not blocked by a recording). If all
cards are in use (i.e. when something is recorded, or by multiple clients), this
applies to Multiple-Card-Systems as well.

If your client suffers from buffer underruns while watching live TV, you can
configure buffering on the server side. Enter a reasonable value (e.g. 300ms)
as "Live TV buffer delay (ms)" in the server setup.

....
With "Maximum Priority" and "Minimum Priority" you can keep VDR from considering
streamdev in certain cases. If for instance you have a streamdev client with its
own DVB card, VDR might use streamdev for recording. If this is not what you
want, you could set the maximum priority to 0. As recordings usually have a much
higher priority (default 50), streamdev is now no longer used for recordings.
The two parameters define the inclusive range of priorities for which streamdev
will accept to tune. Setting the minimum priority to a higher value than the
maximum, you will get two ranges: "up to maximum" and "minimum and above".

Alles anzeigen

Trotz folgender Einstellungen in der setup.conf stoppt das LiveTV für einige Sekunden und ruckelt alle paar Sek. vor sich hin ...

liveTV beim Start pausieren: NEIN, LiveTV Puffer=1500, Server Priorities= -99

Lt. syslog läuft der Server mit "prio=high" Mar 30 18:15:29 BM2LTS-N64native-MCLI vdr: [3627] streamdev server thread started (pid=3596, tid=3627, prio=high)

Code

streamdev-server.AllowSuspend = 1
streamdev-server.HideMenuEntry = 1
streamdev-server.HTTPBindIP = 10.75.25.22
streamdev-server.HTTPPriority = -99
streamdev-server.HTTPServerPort = 3000
streamdev-server.HTTPStreamType = 0
streamdev-server.IGMPBindIP = 10.75.25.22
streamdev-server.IGMPClientPort = 1234
streamdev-server.IGMPPriority = -99
streamdev-server.IGMPStreamType = 0
streamdev-server.LiveBufferMs = 1500
streamdev-server.LoopPrevention = 0
streamdev-server.MaxClients = 5
streamdev-server.ServerPort = 2004
streamdev-server.StartHTTPServer = 1
streamdev-server.StartIGMPServer = 0
streamdev-server.StartServer = 0
streamdev-server.StartSuspended = 0
streamdev-server.VTPBindIP = 10.75.25.22
streamdev-server.VTPPriority = -99

Alles anzeigen

Tja was soll ich sagen ... "mit Latein am Ende" ... ... oder "selber schuld"

gggggg · 30. März 2021

Das Wichtigste hatte ich vergessen ... ich habe dem vdr nur 1 Tuner erlaubt um das Verhalten zu testen !

gggggg · 31. März 2021

Vem VDR ist per mcli 1 Tuner zugeteilt.

Warum gewinnt der streamdev-server mit Prio -99 gegenüber LiveTV (SIXX) mit -1.

Das log startet zum Zeitpunkt der Eingabe von wget localhost:3000/22 DMAX. der wget bricht nach ca. 3s ab.

Code

18:23:27 vdr: [7226] Streamdev: Accepted new client (HTTP) 127.0.0.1:32884
18:23:27 vdr: [7226] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-99 this->Prio:-1 NeedsDetachReceivers:0 -> 1
18:23:27 vdr: [7226] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-99 this->Prio:-1 NeedsDetachReceivers:0 -> 1
18:23:27 vdr: [7226] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:27 vdr: [7226] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:27 vdr: [7557] streamdev-writer thread started (pid=7195, tid=7557, prio=high)
18:23:27 vdr: [7226] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:8, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
18:23:27 vdr: [7226] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:9, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
18:23:27 vdr: [7558] streamdev-livestreaming thread started (pid=7195, tid=7558, prio=high)
18:23:27 vdr: [7195] switching to channel 17 S19.2E-133-5-776 (SIXX)
18:23:27 vdr: [7195] [softhddev]SetPlayMode: 0
18:23:27 vdr: [7195] [softhddev]SetVolumeDevice: 10
18:23:27 vdr: Set Playmode 0
18:23:27 vdr: video: new stream start
18:23:27 vdr: [7195] [softhddev]SetVideoDisplayFormat: 1
18:23:27 vdr: [7195] [softhddev]GetSpuDecoder:
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:767 (DMAX), Type:5, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:768 (DMAX), Type:6, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:27 vdr: [7515] osdteletext-receiver thread ended (pid=7195, tid=7515)
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:35 (DMAX), Type:7, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:27 vdr: [7195] buffer stats: 0 (0%) used
18:23:27 vdr: [7195] mcli::ProvidesChannel: DVB:2 Channel:SIXX, Prio:0 this->Prio:-99 NeedsDetachReceivers:1 -> 1
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:8, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:9, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:27 vdr: video/cuvid: closing eof
18:23:27 vdr: [7195] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:27 vdr: [7195] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:767 (SIXX), Type:5, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:768 (SIXX), Type:6, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:27 vdr: [7514] device 2 receiver thread ended (pid=7195, tid=7514)
18:23:27 vdr: [7560] device 2 receiver thread started (pid=7195, tid=7560, prio=high)
18:23:27 vdr: [7195] mcli::SetPid: DVB:2 Pid:35 (SIXX), Type:7, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:27 vdr: [7195] [softhddev]SetPlayMode: 1
18:23:27 vdr: [7561] osdteletext-receiver thread started (pid=7195, tid=7561, prio=high)
18:23:27 vdr: [7195] [softhddev]SetVolumeDevice: 10
18:23:27 vdr: Set Playmode 1
18:23:28 vdr: [7195] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-99 this->Prio:-1 NeedsDetachReceivers:0 -> 1
18:23:28 vdr: [7195] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:28 vdr: [7195] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:29 vdr: [7195] streamdev: Lost channel 22 (DMAX) on device 1. Continuing on device 1.
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:8, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:9, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] switching to channel 17 S19.2E-133-5-776 (SIXX)
18:23:29 vdr: [7195] [softhddev]SetPlayMode: 0
18:23:29 vdr: [7195] [softhddev]SetVolumeDevice: 10
18:23:29 vdr: Set Playmode 0
18:23:29 vdr: video: new stream start
18:23:29 vdr: [7195] [softhddev]SetVideoDisplayFormat: 1
18:23:29 vdr: [7195] [softhddev]GetSpuDecoder:
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:767 (DMAX), Type:5, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:768 (DMAX), Type:6, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:29 vdr: [7561] osdteletext-receiver thread ended (pid=7195, tid=7561)
18:23:29 vdr: video/cuvid: closing eof
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:35 (DMAX), Type:7, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] buffer stats: 0 (0%) used
18:23:29 vdr: [7195] mcli::ProvidesChannel: DVB:2 Channel:SIXX, Prio:0 this->Prio:-99 NeedsDetachReceivers:1 -> 1
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:8, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:9, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:29 vdr: [7195] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:29 vdr: [7560] device 2 receiver thread ended (pid=7195, tid=7560)
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:767 (SIXX), Type:5, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:768 (SIXX), Type:6, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:29 vdr: [7568] device 2 receiver thread started (pid=7195, tid=7568, prio=high)
18:23:29 vdr: [7195] mcli::SetPid: DVB:2 Pid:35 (SIXX), Type:7, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:29 vdr: [7195] [softhddev]SetPlayMode: 1
18:23:29 vdr: [7195] [softhddev]SetVolumeDevice: 10
18:23:29 vdr: Set Playmode 1
18:23:29 vdr: [7569] osdteletext-receiver thread started (pid=7195, tid=7569, prio=high)
18:23:29 vdr: video: set trick-speed 0
18:23:30 vdr: [7195] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-99 this->Prio:-1 NeedsDetachReceivers:0 -> 1
18:23:30 vdr: [7557] streamdev-server: streamer done - writer exiting
18:23:30 vdr: [7557] streamdev-server: closing HTTP connection to 127.0.0.1:32884
18:23:30 vdr: [7557] streamdev-writer thread ended (pid=7195, tid=7557)
18:23:30 vdr: [7195] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:30 vdr: [7195] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:30 vdr: [7195] streamdev: Lost channel 22 (DMAX) on device 1. Continuing on device 1.
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:8, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:9, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
18:23:30 vdr: [7195] switching to channel 17 S19.2E-133-5-776 (SIXX)
18:23:30 vdr: [7195] [softhddev]SetPlayMode: 0
18:23:30 vdr: [7195] [softhddev]SetVolumeDevice: 10
18:23:30 vdr: Set Playmode 0
18:23:30 vdr: video: new stream start
18:23:30 vdr: [7195] [softhddev]SetVideoDisplayFormat: 1
18:23:30 vdr: [7195] [softhddev]GetSpuDecoder:
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:767 (DMAX), Type:5, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:768 (DMAX), Type:6, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:30 vdr: [7569] osdteletext-receiver thread ended (pid=7195, tid=7569)
18:23:30 vdr: video/cuvid: closing eof
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:35 (DMAX), Type:7, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:30 vdr: [7195] buffer stats: 0 (0%) used
18:23:30 vdr: [7195] mcli::ProvidesChannel: DVB:2 Channel:SIXX, Prio:0 this->Prio:-99 NeedsDetachReceivers:1 -> 1
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:8, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:9, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
18:23:30 vdr: [7558] streamdev-livestreaming thread ended (pid=7195, tid=7558)
18:23:30 vdr: [7195] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:30 vdr: [7195] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
18:23:30 vdr: [7226] buffer stats: 0 (0%) used
18:23:30 vdr: [7568] device 2 receiver thread ended (pid=7195, tid=7568)
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:767 (SIXX), Type:5, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:768 (SIXX), Type:6, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:30 vdr: [7572] device 2 receiver thread started (pid=7195, tid=7572, prio=high)
18:23:30 vdr: [7195] mcli::SetPid: DVB:2 Pid:35 (SIXX), Type:7, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
18:23:30 vdr: [7573] osdteletext-receiver thread started (pid=7195, tid=7573, prio=high)
18:23:30 vdr: [7195] [softhddev]SetPlayMode: 1
18:23:30 vdr: [7195] [softhddev]SetVolumeDevice: 10
18:23:30 vdr: Set Playmode 1
18:23:30 vdr: video: set trick-speed 0
18:23:30 vdr[7195]: mcli::recv_ts_func: Discontinuity on receiver 0x560f33d43a50 for pid 35: 1->3 at pos 0/1

Alles anzeigen

gggggg · 31. März 2021

Interessehalber hab ich dem streamdev mal Prio 99 eingestellt und prompt "raucht" der vdr ab

(Mit Prio 0 läuft der wget bis CTRL-C durch)

Code

Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] Streamdev: Accepted new client (HTTP) 127.0.0.1:32894
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:99 this->Prio:-1 NeedsDetachReceivers:1 -> 1
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:99 this->Prio:-1 NeedsDetachReceivers:1 -> 1
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] [softhddev]SetPlayMode: 0
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] [softhddev]SetVolumeDevice: 10
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: Set Playmode 0
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: video: set closing
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: video: set clock --:--:--.---
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: video: reset start
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: video: set clock --:--:--.---
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: video: new stream start
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] [softhddev]SetVideoDisplayFormat: 1
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] [softhddev]GetSpuDecoder:
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] mcli::SetPid: DVB:2 Pid:767 (SIXX), Type:5, On:0, used:0 sid:776 ca_enable:1 channel_ca:0
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7226] mcli::SetPid: DVB:2 Pid:768 (SIXX), Type:6, On:0, used:0 sid:776 ca_enable:1 channel_ca:0
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7195] switching to channel 17 S19.2E-133-5-776 (SIXX)
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr: [7195] buffer stats: 0 (0%) used
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr[7195]: pure virtual method called
Mar 31 18:48:45 BM2LTS-N64native-MCLI vdr[7195]: terminate called without an active exception
Mar 31 18:48:45 BM2LTS-N64native-MCLI systemd[1]: vdr.service: Main process exited, code=killed, status=6/ABRT
Mar 31 18:48:45 BM2LTS-N64native-MCLI systemd[1]: vdr.service: Failed with result 'signal'.

Alles anzeigen

gggggg · 31. März 2021

auch mit 3 Tunern gibt es einen kurzen stop beim liveTV:

Code

19:29:22 vdr: codec/audio: drift(     0) 1304ms reset
19:29:22 vdr: codec/audio: drift(     0)  1304577us     0
19:29:22 vdr: [12561] EPGSearch: search timer update started
19:29:22 vdr: [12561] EPGSearch: search timer update finished
19:29:22 vdr: [12561] EPGSearch: check for timer conflicts
19:29:22 vdr: [12561] EPGSearch: check for timer conflicts - done
19:29:22 vdr: codec/audio: inital drift delay 1287ms
19:29:23 vdr: [12576] Streamdev: Accepted new client (HTTP) 127.0.0.1:33004
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12576] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12594] streamdev-livestreaming thread started (pid=12544, tid=12594, prio=high)
19:29:23 vdr: [12593] streamdev-writer thread started (pid=12544, tid=12593, prio=high)
19:29:23 vdr: [12544] switching to channel 17 S19.2E-133-5-776 (SIXX)
19:29:23 vdr: [12544] [softhddev]SetPlayMode: 0
19:29:23 vdr: [12544] [softhddev]SetVolumeDevice: 8
19:29:23 vdr: video: new stream start
19:29:23 vdr: [12544] [softhddev]SetVideoDisplayFormat: 1
19:29:23 vdr: [12544] [softhddev]GetSpuDecoder:
19:29:23 vdr: [12581] osdteletext-receiver thread ended (pid=12544, tid=12581)
19:29:23 vdr: [12544] buffer stats: 0 (0%) used
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'Priority >= 0 && Receiving (true)' is True
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * '!IsTunedToTransponder(Channel)' is True
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG DVB:3 Channel:SIXX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG DVB:3 Channel:SIXX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG DVB:4 Channel:SIXX * 'ProvidesTransponder(Channel)' is True
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
19:29:23 vdr: [12544] mcli::ProvidesChannel: DEBUG DVB:4 Channel:SIXX * 'Priority >= 0 && Receiving (true)' is False
19:29:23 vdr: [12596] device 3 receiver thread started (pid=12544, tid=12596, prio=high)
19:29:23 vdr: [12544] [softhddev]SetPlayMode: 1
19:29:23 vdr: [12597] osdteletext-receiver thread started (pid=12544, tid=12597, prio=high)
19:29:23 vdr: [12544] [softhddev]SetVolumeDevice: 8
19:29:23 vdr: Set Playmode 1
19:29:23 vdr: video: set trick-speed 0
19:29:23 vdr[12544]: mcli::recv_ts_func: Discontinuity on receiver 0x5581919c17d0 for pid 3327: 12->5 at pos 0/7
19:29:24 vdr: [12602] mcli: sections assembler thread started (pid=12544, tid=12602, prio=high)
19:29:24 vdr: codec/audio: inital drift delay 373ms
19:29:25 vdr: video: slow down video, duping frame 87 
19:29:25 vdr: video/cuvid: synced after 54 frames 1370ms
19:29:32 vdr: [12576] client (HTTP) 127.0.0.1:33004 has closed connection
19:29:32 vdr: [12593] ERROR: streamdev-server: couldn't send 79220 bytes: Die Verbindung wurde vom Kommunikationspartner zurÃ¼ckgesetzt
19:29:32 vdr: [12576] streamdev-server: closing HTTP connection to 127.0.0.1:33004
19:29:32 vdr: [12593] streamdev-server: closing HTTP connection to 127.0.0.1:33004
19:29:32 vdr: [12593] streamdev-writer thread ended (pid=12544, tid=12593)
19:29:32 vdr: [12580] device 2 receiver thread ended (pid=12544, tid=12580)
19:29:32 vdr: [12594] streamdev-livestreaming thread ended (pid=12544, tid=12594)
19:29:32 vdr: [12576] buffer stats: 974969 (25%) used

Alles anzeigen

gggggg · 2. April 2021

HelmutB pbrb ... ich vermute dass mcli mit den Prioritäten nicht richtig umgeht, weil

- der Streamdev-server mit Prio -99 dem LiveTV mit Prio 0/-1 den Tuner weg nimmt

- und das passiert nicht nur mit einem Tuner, sondern selbst wenn mehrere Tuner verfügbar sind.

Wie beurteilt ihr das lt. den logs ab Post #3 ?

Wie sollte eig. PrimaryDVB=1 und PrimaryLimit=0 eingestellt sein ?

HelmutB · 2. April 2021

Möglicherweise liegt es an diesem Commit für vdr-1.7.25: Revised priority handling.

Der Patch für mcli:

Diff

diff -Nurp --no-dereference vdr-plugin-mcli-0.9.6_pre6/device.c vdr-plugin-mcli-0.9.6_pre6_p01/device.c
--- vdr-plugin-mcli-0.9.6_pre6/device.c    2021-03-30 22:42:37.000000000 +0200
+++ vdr-plugin-mcli-0.9.6_pre6_p01/device.c    2021-04-02 16:37:30.480021730 +0200
@@ -450,8 +450,9 @@ bool cMcliDevice::CheckCAM(const cChanne
 bool cMcliDevice::ProvidesChannel (const cChannel * Channel, int Priority, bool * NeedsDetachReceivers) const
 {
     bool result = false;
-    bool hasPriority = Priority < 0 || Priority > this->Priority ();
+    bool hasPriority = Priority == IDLEPRIORITY || Priority > this->Priority();
     bool needsDetachReceivers = false;
+
     if (!m_enable) {
         return false;
     }
diff -Nurp --no-dereference vdr-plugin-mcli-0.9.6_pre6/device.h vdr-plugin-mcli-0.9.6_pre6_p01/device.h
--- vdr-plugin-mcli-0.9.6_pre6/device.h    2021-03-30 22:42:37.000000000 +0200
+++ vdr-plugin-mcli-0.9.6_pre6_p01/device.h    2021-04-02 16:43:23.286690187 +0200
@@ -105,7 +105,7 @@ class cMcliDevice:public cDevice
     }
     virtual bool ProvidesSource (int Source) const;
     virtual bool ProvidesTransponder (const cChannel * Channel) const;
-    virtual bool ProvidesChannel (const cChannel * Channel, int Priority = -1, bool * NeedsDetachReceivers = NULL) const;
+    virtual bool ProvidesChannel (const cChannel *Channel, int Priority = IDLEPRIORITY, bool *NeedsDetachReceivers = NULL) const;
     virtual bool IsTunedToTransponder (const cChannel * Channel) const;
 
     virtual int HandleTsData (unsigned char *buffer, size_t len);

Alles anzeigen

Im Anhang vdr-plugin-mcli-0.9.6_p01 mit diesem Patch.

LG Helmut

HelmutB · 2. April 2021

Der fix-handling-IDLEPRIORITY Commit für vdr-1.7.27 sollte besser auch noch dabei sein.

Diff

--- a/device.c.p01    2021-04-02 16:37:30.480021730 +0200
+++ b/device.c    2021-04-02 17:18:15.633367531 +0200
@@ -478,7 +478,7 @@ bool cMcliDevice::ProvidesChannel (const
         )
 #endif
 
-        if (Priority >= 0 && Receiving (true))
+        if (Priority > IDLEPRIORITY && Receiving (true))
         {
 #ifdef DEBUG_TUNE_PC
             DEBUG_MASK(DEBUG_BIT_TUNE_PC,

Alles anzeigen

LG helmut

gggggg · 2. April 2021

Danke HelmutB ... wie immer scheinst du wieder mal ins Schwarze getroffen zu haben ... denke ich jedenfalls. Schau mal ... ich teste mal mit einem tuner weiter

Ich hab dem Stramdev Prio. -3 verpasst !

Code

Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] Streamdev: Accepted new client (HTTP) 10.75.25.22:49848
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-3 this->Prio:-1 NeedsDetachReceivers:0 -> 0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DVB:3 Channel:DMAX, Prio:-3 this->Prio:-100 NeedsDetachReceivers:0 -> 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DVB:4 Channel:DMAX, Prio:-3 this->Prio:-100 NeedsDetachReceivers:0 -> 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-3 this->Prio:-1 NeedsDetachReceivers:0 -> 0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DVB:3 Channel:DMAX, Prio:-3 this->Prio:-100 NeedsDetachReceivers:0 -> 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DEBUG DVB:4 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::ProvidesChannel: DVB:4 Channel:DMAX, Prio:-3 this->Prio:-100 NeedsDetachReceivers:0 -> 1
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::SetChannelDevice: Request tuning on DVB:3 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::SetChannelDevice: Really tuning now DVB:3 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::SetPid: DVB:3 Pid:3327 (DMAX), Type:5, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [5082] streamdev-writer thread started (pid=4885, tid=5082, prio=high)
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4908] mcli::SetPid: DVB:3 Pid:3328 (DMAX), Type:6, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [5083] streamdev-livestreaming thread started (pid=4885, tid=5083, prio=high)
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [5084] device 3 receiver thread started (pid=4885, tid=5084, prio=high)
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [5081] mcli::handle_ten: Signal lost
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4911] mcli::handle_ten: Status:1f, Strength:fb00, SNR:d2b4, BER:0000
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [5085] mcli: sections assembler thread started (pid=4885, tid=5085, prio=high)
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:108 (DMAX), Type:7, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:17 (DMAX), Type:8, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:20 (DMAX), Type:9, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:18 (DMAX), Type:10, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:44 (DMAX), Type:11, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:11 BM2LTS-N64native-MCLI vdr: [4893] mcli::SetPid: DVB:3 Pid:108 (DMAX), Type:7, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:42:12 BM2LTS-N64native-MCLI vdr: codec/audio: drift(     0)    43655us 20954
Apr  2 17:42:12 BM2LTS-N64native-MCLI vdr: [4893] ERROR: 1 ring buffer overflow (188 bytes dropped)
Apr  2 17:42:26 BM2LTS-N64native-MCLI vdr: [4908] client (HTTP) 10.75.25.22:49848 has closed connection
Apr  2 17:42:26 BM2LTS-N64native-MCLI vdr: [4908] streamdev-server: closing HTTP connection to 10.75.25.22:49848

Alles anzeigen

gggggg · 2. April 2021

Auch mit 1 Tuner scheint es OK:

Code

Apr  2 17:48:54 BM2LTS-N64native-MCLI vdr: [5140] Streamdev: Accepted new client (HTTP) 10.75.25.22:49850
Apr  2 17:48:54 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:48:54 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 17:48:54 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 17:48:54 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-3 this->Prio:-1 NeedsDetachReceivers:0 -> 0
Apr  2 17:48:54 BM2LTS-N64native-MCLI vdr: [5140] streamdev: No device provides channel 22 (DMAX) at priority -3
Apr  2 17:48:54 BM2LTS-N64native-MCLI vdr: [5140] streamdev-server: closing HTTP connection to 10.75.25.22:49850

Hier die Antwort vom Streamdev:

Code

root@BM2LTS-N64native-MCLI:/tmp# wget 10.75.25.22:3000/22
--2021-04-02 17:48:54--  http://10.75.25.22:3000/22
Verbindungsaufbau zu 10.75.25.22:3000 … verbunden.
HTTP-Anforderung gesendet, auf Antwort wird gewartet … 503 Service Unavailable
2021-04-02 17:48:54 FEHLER 503: Service Unavailable.

gggggg · 2. April 2021

Nun mit Streamdev Prio =0 (LiveTv hat -1)

Code

Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr[5116]: last: 3
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] Streamdev: Accepted new client (HTTP) 10.75.25.22:49860
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:0 this->Prio:-1 NeedsDetachReceivers:1 -> 1
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:0 this->Prio:-1 NeedsDetachReceivers:1 -> 1
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] [softhddev]SetPlayMode: 0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] [softhddev]SetVolumeDevice: 8
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: Set Playmode 0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: video: set closing
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: video: set clock --:--:--.---
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: video: reset start
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: video: set clock --:--:--.---
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: video: new stream start
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] [softhddev]SetVideoDisplayFormat: 1
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] [softhddev]GetSpuDecoder:
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::SetPid: DVB:2 Pid:767 (SIXX), Type:5, On:0, used:0 sid:776 ca_enable:1 channel_ca:0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::SetPid: DVB:2 Pid:768 (SIXX), Type:6, On:0, used:0 sid:776 ca_enable:1 channel_ca:0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: video/cuvid: closing eof
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5221] streamdev-writer thread started (pid=5116, tid=5221, prio=high)
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:5, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5140] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:6, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5222] streamdev-livestreaming thread started (pid=5116, tid=5222, prio=high)
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5214] device 2 receiver thread ended (pid=5116, tid=5214)
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5223] device 2 receiver thread started (pid=5116, tid=5223, prio=high)
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] switching to channel 17 S19.2E-133-5-776 (SIXX)
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * '!IsTunedToTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DVB:2 Channel:SIXX, Prio:0 this->Prio:0 NeedsDetachReceivers:1 -> 0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] switching to channel 22 S19.2E-133-33-63 (DMAX)
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:0 this->Prio:0 NeedsDetachReceivers:1 -> 0
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] info: Streamen im Gange
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] [softhddev]CreateOsd: left 96, top 989, level 0, using OpenGL OSD support
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5116] [softhddev]cOglOsd osdLeft 96 osdTop 989 screenWidth 1920 screenHeight 1080
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5220] mcli::handle_ten: Signal lost
Apr  2 17:59:55 BM2LTS-N64native-MCLI vdr: [5220] mcli::handle_ten: Status:1f, Strength:ffff, SNR:dce0, BER:0000
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:108 (DMAX), Type:7, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:17 (DMAX), Type:8, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:20 (DMAX), Type:9, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:18 (DMAX), Type:10, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:44 (DMAX), Type:11, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:56 BM2LTS-N64native-MCLI vdr: [5124] mcli::SetPid: DVB:2 Pid:108 (DMAX), Type:7, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 17:59:57 BM2LTS-N64native-MCLI vdr: [5124] ERROR: 1 ring buffer overflow (188 bytes dropped)
Apr  2 18:00:01 BM2LTS-N64native-MCLI vdr: [5116] info: Kanal nicht verfÃ¼gbar!
Apr  2 18:00:01 BM2LTS-N64native-MCLI vdr: [5116] [softhddev]CreateOsd: left 96, top 989, level 0, using OpenGL OSD support
Apr  2 18:00:01 BM2LTS-N64native-MCLI vdr: [5116] [softhddev]cOglOsd osdLeft 96 osdTop 989 screenWidth 1920 screenHeight 1080
Apr  2 18:00:08 BM2LTS-N64native-MCLI vdr: [5116] info: Kanal nicht verfÃ¼gbar!
Apr  2 18:00:08 BM2LTS-N64native-MCLI vdr: [5116] [softhddev]CreateOsd: left 96, top 989, level 0, using OpenGL OSD support
Apr  2 18:00:08 BM2LTS-N64native-MCLI vdr: [5116] [softhddev]cOglOsd osdLeft 96 osdTop 989 screenWidth 1920 screenHeight 1080
Apr  2 18:00:50 BM2LTS-N64native-MCLI vdr: [5224] epg data writer thread started (pid=5116, tid=5224, prio=low)
Apr  2 18:00:50 BM2LTS-N64native-MCLI vdr: [5224] epg data writer thread ended (pid=5116, tid=5224)

Alles anzeigen

Prinzipiell OK, weil Streamdev gewinnt und am TV erscheint "Stream im Gange". Dann erscheint "Kanal nicht verfügbar".

1 Sollte nicht das LiveTV auf den einzig verfügba. Kanal = Streamdev =22 = DMAX wechslen ?

Wenn ich den Stream stoppe läuft LiveTV mit SIXX weiter.

Und den habe ich auch in obigem Log:

17:59:57 BM2LTS-N64native-MCLI vdr: [5124] ERROR: 1 ring buffer overflow (188 bytes dropped)

gggggg · 2. April 2021

HelmutB ich hab die obigen Tests mit deinem 096p1 (meldet sich als p6) gemeacht ... hast dann noch einen p2 gemacht ?

gggggg · 2. April 2021

Folgende Tests mit deinem p2:

Streamprio=0 ... ich würde sagen .. ist gleich #12

Code

Apr  2 18:45:16 vdr: [5561] Streamdev: Accepted new client (HTTP) 10.75.25.22:49866
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:0 this->Prio:-1 NeedsDetachReceivers:1 -> 1
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5561] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:0 this->Prio:-1 NeedsDetachReceivers:1 -> 1
Apr  2 18:45:16 vdr: [5561] [softhddev]SetPlayMode: 0
Apr  2 18:45:16 vdr: [5561] [softhddev]SetVolumeDevice: 8
Apr  2 18:45:16 vdr: Set Playmode 0
Apr  2 18:45:16 vdr: [5561] mcli::SetPid: DVB:2 Pid:767 (SIXX), Type:5, On:0, used:0 sid:776 ca_enable:1 channel_ca:0
Apr  2 18:45:16 vdr: [5561] mcli::SetPid: DVB:2 Pid:768 (SIXX), Type:6, On:0, used:0 sid:776 ca_enable:1 channel_ca:0
Apr  2 18:45:16 vdr: [5582] device 2 receiver thread ended (pid=5538, tid=5582)
Apr  2 18:45:16 vdr: video/cuvid: closing eof
Apr  2 18:45:16 vdr: [5561] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 18:45:16 vdr: [5561] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 18:45:16 vdr: [5561] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:5, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:16 vdr: [8714] streamdev-livestreaming thread started (pid=5538, tid=8714, prio=high)
Apr  2 18:45:16 vdr: [8713] streamdev-writer thread started (pid=5538, tid=8713, prio=high)
Apr  2 18:45:16 vdr: [5561] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:6, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:16 vdr: [8715] device 2 receiver thread started (pid=5538, tid=8715, prio=high)
Apr  2 18:45:16 vdr: [8712] mcli::handle_ten: Signal lost
Apr  2 18:45:16 vdr: [5538] switching to channel 17 S19.2E-133-5-776 (SIXX)
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * '!IsTunedToTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DVB:2 Channel:SIXX, Prio:0 this->Prio:0 NeedsDetachReceivers:1 -> 0
Apr  2 18:45:16 vdr: [5538] switching to channel 22 S19.2E-133-33-63 (DMAX)
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 18:45:16 vdr: [5538] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:0 this->Prio:0 NeedsDetachReceivers:1 -> 0
Apr  2 18:45:16 vdr: [5538] info: Streamen im Gange
Apr  2 18:45:16 vdr: [5538] [softhddev]CreateOsd: left 96, top 989, level 0, using OpenGL OSD support
Apr  2 18:45:16 vdr: [5538] [softhddev]cOglOsd osdLeft 96 osdTop 989 screenWidth 1920 screenHeight 1080
Apr  2 18:45:17 vdr[5538]: mcli::recv_ts_func: Discontinuity on receiver 0x55f05eb41ee0 for pid 3327: 7->9 at pos 0/7
Apr  2 18:45:17 vdr: [8712] mcli::handle_ten: Status:1f, Strength:ffff, SNR:dce0, BER:0000
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:108 (DMAX), Type:7, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:17 (DMAX), Type:8, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:20 (DMAX), Type:9, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:18 (DMAX), Type:10, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:44 (DMAX), Type:11, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:17 vdr: [5545] mcli::SetPid: DVB:2 Pid:108 (DMAX), Type:7, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:18 vdr: [5545] ERROR: 1 ring buffer overflow (188 bytes dropped)
Apr  2 18:45:22 vdr: [5538] info: Kanal nicht verfÃ¼gbar!
Apr  2 18:45:22 vdr: [5538] [softhddev]CreateOsd: left 96, top 989, level 0, using OpenGL OSD support
Apr  2 18:45:22 vdr: [5538] [softhddev]cOglOsd osdLeft 96 osdTop 989 screenWidth 1920 screenHeight 1080
Apr  2 18:45:29 vdr: [5538] info: Kanal nicht verfÃ¼gbar!
Apr  2 18:45:29 vdr: [5538] [softhddev]CreateOsd: left 96, top 989, level 0, using OpenGL OSD support
Apr  2 18:45:29 vdr: [5538] [softhddev]cOglOsd osdLeft 96 osdTop 989 screenWidth 1920 screenHeight 1080
Apr  2 18:45:37 vdr: [5561] client (HTTP) 10.75.25.22:49866 has closed connection
Apr  2 18:45:37 vdr: [5561] streamdev-server: closing HTTP connection to 10.75.25.22:49866
Apr  2 18:45:37 vdr: [5561] mcli::SetPid: DVB:2 Pid:3327 (DMAX), Type:5, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:37 vdr: [5561] mcli::SetPid: DVB:2 Pid:108 (DMAX), Type:7, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:37 vdr: [5561] mcli::SetPid: DVB:2 Pid:17 (DMAX), Type:8, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:37 vdr: [5561] mcli::SetPid: DVB:2 Pid:20 (DMAX), Type:9, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:37 vdr: [5561] mcli::SetPid: DVB:2 Pid:18 (DMAX), Type:10, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:37 vdr: [5561] mcli::SetPid: DVB:2 Pid:44 (DMAX), Type:11, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:37 vdr: [5561] mcli::SetPid: DVB:2 Pid:3328 (DMAX), Type:6, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:45:37 vdr: [8714] streamdev-livestreaming thread ended (pid=5538, tid=8714)
Apr  2 18:45:37 vdr: [8713] streamdev-writer thread ended (pid=5538, tid=8713)
Apr  2 18:45:37 vdr: [5561] buffer stats: 1169360 (31%) used
Apr  2 18:45:37 vdr: [8715] device 2 receiver thread ended (pid=5538, tid=8715)
Apr  2 18:45:47 vdr: [5538] switching to channel 17 S19.2E-133-5-776 (SIXX)
Apr  2 18:45:47 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:45:47 vdr: [5538] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 18:45:47 vdr: [5538] mcli::ProvidesChannel: DEBUG DVB:2 Channel:SIXX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 18:45:47 vdr: [5538] mcli::ProvidesChannel: DVB:2 Channel:SIXX, Prio:0 this->Prio:-100 NeedsDetachReceivers:0 -> 1
Apr  2 18:45:47 vdr: [5538] mcli::SetChannelDevice: Request tuning on DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 18:45:47 vdr: [5538] mcli::SetChannelDevice: Really tuning now DVB:2 to Channel:SIXX, Provider:ProSiebenSat.1, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 18:45:47 vdr: [5538] mcli::SetPid: DVB:2 Pid:767 (SIXX), Type:5, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
Apr  2 18:45:47 vdr: [5538] mcli::SetPid: DVB:2 Pid:768 (SIXX), Type:6, On:1, used:1 sid:776 ca_enable:1 channel_ca:0
Apr  2 18:45:47 vdr: [8718] device 2 receiver thread started (pid=5538, tid=8718, prio=high)
Apr  2 18:45:48 vdr: [8717] mcli::handle_ten: Signal lost
Apr  2 18:45:48 vdr: [8717] mcli::handle_ten: Status:1f, Strength:fa00, SNR:d2b4, BER:0000
Apr  2 18:45:48 vdr: [5538] [softhddev]SetPlayMode: 1
Apr  2 18:45:48 vdr: [5538] [softhddev]SetVolumeDevice: 8
Apr  2 18:45:48 vdr: Set Playmode 1

Alles anzeigen

gggggg · 2. April 2021

Streamprio= -3 oder -1 ... ich würde sagen .. ist gleich #11

Code

Apr  2 18:52:04 BM2LTS-N64native-MCLI systemd[1]: getty@tty1.service: Succeeded.
Apr  2 18:52:04 BM2LTS-N64native-MCLI systemd[1]: getty@tty1.service: Scheduled restart job, restart counter is at 6.
Apr  2 18:52:04 BM2LTS-N64native-MCLI systemd[1]: Stopped Getty on tty1.
Apr  2 18:52:04 BM2LTS-N64native-MCLI systemd[1]: Started Getty on tty1.
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] Streamdev: Accepted new client (HTTP) 10.75.25.22:49868
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-3 this->Prio:-1 NeedsDetachReceivers:1 -> 0
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] streamdev: No device provides channel 22 (DMAX) at priority -3
Apr  2 18:52:06 BM2LTS-N64native-MCLI vdr: [5561] streamdev-server: closing HTTP connection to 10.75.25.22:49868

Alles anzeigen

gggggg · 2. April 2021

mit 2 Tunern Streamprio= -3 oder -1 ... ich würde sagen .. ist gleich #10

Code

Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] Streamdev: Accepted new client (HTTP) 10.75.25.22:49872
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-1 this->Prio:-1 NeedsDetachReceivers:1 -> 0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DVB:3 Channel:DMAX, Prio:-1 this->Prio:-100 NeedsDetachReceivers:0 -> 1
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG result 0 hasPriority 0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:2 Channel:DMAX * '!IsTunedToTransponder(Channel)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DVB:2 Channel:DMAX, Prio:-1 this->Prio:-1 NeedsDetachReceivers:1 -> 0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'ProvidesTransponder(Channel)' is True
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG result 1 hasPriority 1
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DEBUG DVB:3 Channel:DMAX * 'Priority >= 0 && Receiving (true)' is False
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::ProvidesChannel: DVB:3 Channel:DMAX, Prio:-1 this->Prio:-100 NeedsDetachReceivers:0 -> 1
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetChannelDevice: Request tuning on DVB:3 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetChannelDevice: Really tuning now DVB:3 to Channel:DMAX, Provider:BetaDigital, Source:1392509120, LiveView:false, IsScan:0 CA:0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8828] streamdev-writer thread started (pid=8789, tid=8828, prio=high)
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:3327 (DMAX), Type:5, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8829] streamdev-livestreaming thread started (pid=8789, tid=8829, prio=high)
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:3328 (DMAX), Type:6, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8830] device 3 receiver thread started (pid=8789, tid=8830, prio=high)
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8831] mcli: sections assembler thread started (pid=8789, tid=8831, prio=high)
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:108 (DMAX), Type:7, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:41 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:17 (DMAX), Type:8, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:20 (DMAX), Type:9, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:18 (DMAX), Type:10, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:44 (DMAX), Type:11, On:1, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:3327 (DMAX), Type:5, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:3328 (DMAX), Type:6, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] mcli::SetPid: DVB:3 Pid:108 (DMAX), Type:7, On:0, used:1 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:42 BM2LTS-N64native-MCLI vdr: [8797] ERROR: 1 ring buffer overflow (188 bytes dropped)
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] client (HTTP) 10.75.25.22:49872 has closed connection
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] streamdev-server: closing HTTP connection to 10.75.25.22:49872
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:3327 (DMAX), Type:5, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:108 (DMAX), Type:7, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:17 (DMAX), Type:8, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:20 (DMAX), Type:9, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:18 (DMAX), Type:10, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:44 (DMAX), Type:11, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] mcli::SetPid: DVB:3 Pid:3328 (DMAX), Type:6, On:0, used:0 sid:63 ca_enable:1 channel_ca:0
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8830] device 3 receiver thread ended (pid=8789, tid=8830)
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8829] streamdev-livestreaming thread ended (pid=8789, tid=8829)
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8828] streamdev-writer thread ended (pid=8789, tid=8828)
Apr  2 18:55:48 BM2LTS-N64native-MCLI vdr: [8812] buffer stats: 877208 (23%) used

Alles anzeigen

HelmutB · 2. April 2021

Warum hast du die Prioritäten des Server verändert? Versuche es doch einfach mit den Standardwerten.

Hier meine funktionierenden Server und Clienteinstellungen (bei mir natürlich ohne mcli-devices).

server

client

LG Helmut

gggggg · 3. April 2021

HelmutB weil der Server in meinem Fall zum updaten des EPG genutzt wird und damit die niedrigste Prio haben muss. In Folgendem Script erfolgt die Kommunikation nicht mit dem Client, sondern per wget ... EPG Update steuern - die 100ste

Prinzipiell ist aus meiner Sicht mit dem Patch p2 nun ja Alles OK.

Was bleibt ist:

Wenn Streamdev gewinnt erscheint am TV "Stream im Gange". Dann erscheint "Kanal nicht verfügbar".

Aber sollte nicht das LiveTV auf den einzig verfügbaren Kanal = Streamdev =22 = DMAX (oder einen Kanal der Gruppe) wechseln ?

Wenn ich den Stream stoppe läuft LiveTV mit SIXX weiter.

Weist du warum das so ist ?

Ev. kannst du mal bei dir mit 1 Tuner testen ...

HelmutB · 3. April 2021

Ich habe es jetzt so getestet: 2 Devices, Auf Device 1 läuft eine Aufnahme auf Kanal 5, Device 3 iäuft mit IDLEPRIORITY (-100).

Streamdev-server Http-Priority ist 0. Dann wird mit wget alle 10s auf die Kanäle 5, 6 und 7 umgeschalten.

wget - client

Im Syslog des Server - mit einer debug-Ausgabe in GetDevice()

Spoiler anzeigen

Apr 3 13:51:43 gentoo64vdr vdr[2897]: [3061] Streamdev: Accepted new client (HTTP) 10.0.0.5:45920

Apr 3 13:51:43 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 5 - candidate dev 1, imp 04B2C000, ndr 0 Live:0 Prio: 0/50 Q

Apr 3 13:51:43 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 5 - candidate dev 3, imp 0B400000, ndr 0 Live:0 Prio: 0/-100 Q

Apr 3 13:51:43 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 5 - candidate dev 1, imp 04B2C000, ndr 0 Live:0 Prio: 0/50

Apr 3 13:51:43 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 5 - candidate dev 3, imp 0B400000, ndr 0 Live:0 Prio: 0/-100

Apr 3 13:51:43 gentoo64vdr vdr[2897]: [4268] streamdev-livestreaming thread started (pid=2897, tid=4268, prio=high)

Apr 3 13:51:43 gentoo64vdr vdr[2897]: [4267] streamdev-writer thread started (pid=2897, tid=4267, prio=high)

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [3061] client (HTTP) 10.0.0.5:45920 has closed connection

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [3061] streamdev-server: closing HTTP connection to 10.0.0.5:45920

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [4268] streamdev-livestreaming thread ended (pid=2897, tid=4268)

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [4267] streamdev-writer thread ended (pid=2897, tid=4267)

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [3061] Streamdev: Accepted new client (HTTP) 10.0.0.5:45922

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 6 - candidate dev 3, imp 0B400000, ndr 0 Live:0 Prio: 0/-100 Q

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 6 - candidate dev 3, imp 0B400000, ndr 0 Live:0 Prio: 0/-100

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [4270] streamdev-writer thread started (pid=2897, tid=4270, prio=high)

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [4271] streamdev-livestreaming thread started (pid=2897, tid=4271, prio=high)

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [4272] device 3 receiver thread started (pid=2897, tid=4272, prio=high)

Apr 3 13:51:53 gentoo64vdr vdr[2897]: [4273] device 3 TS buffer thread started (pid=2897, tid=4273, prio=high)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [3061] client (HTTP) 10.0.0.5:45922 has closed connection

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [3061] streamdev-server: closing HTTP connection to 10.0.0.5:45922

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4270] streamdev-writer thread ended (pid=2897, tid=4270)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4271] streamdev-livestreaming thread ended (pid=2897, tid=4271)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [3061] Streamdev: Accepted new client (HTTP) 10.0.0.5:45924

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 7 - candidate dev 3, imp 0B400000, ndr 0 Live:0 Prio: 0/-100 Q

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [3061] GetDevice: ch 7 - candidate dev 3, imp 0B400000, ndr 0 Live:0 Prio: 0/-100

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4275] streamdev-livestreaming thread started (pid=2897, tid=4275, prio=high)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4274] streamdev-writer thread started (pid=2897, tid=4274, prio=high)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4273] device 3 TS buffer thread ended (pid=2897, tid=4273)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4272] device 3 receiver thread ended (pid=2897, tid=4272)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4277] device 3 receiver thread started (pid=2897, tid=4277, prio=high)

Apr 3 13:52:03 gentoo64vdr vdr[2897]: [4278] device 3 TS buffer thread started (pid=2897, tid=4278, prio=high)

Apr 3 13:52:13 gentoo64vdr vdr[2897]: [3061] client (HTTP) 10.0.0.5:45924 has closed connection

Apr 3 13:52:13 gentoo64vdr vdr[2897]: [3061] streamdev-server: closing HTTP connection to 10.0.0.5:45924

Apr 3 13:52:13 gentoo64vdr vdr[2897]: [4275] streamdev-livestreaming thread ended (pid=2897, tid=4275)

Apr 3 13:52:13 gentoo64vdr vdr[2897]: [4274] streamdev-writer thread ended (pid=2897, tid=4274)

Apr 3 13:52:13 gentoo64vdr vdr[2897]: [4278] device 3 TS buffer thread ended (pid=2897, tid=4278)

Apr 3 13:52:13 gentoo64vdr vdr[2897]: [4277] device 3 receiver thread ended (pid=2897, tid=4277)

Soweit alles wie zu erwarten. Wichtig ist meiner Meinung nach, dass das timeout für das Einlesen der EPG-Daten mindestens 15s bis 20s sein sollte. Bei nur 1s wird ziemlich sicher der Transponder zu schnell weggeschalten.

LG Helmut

gggggg · 3. April 2021

JA ist ja eh bei mir auch OK. Du musst es mal mit einem Device versuchen, wenn dann der streamdev dem liveTv das Device nimmt !!

Da solle das liveTv auf einen verfügbaren Kanal = einem der Kanalgruppe des Streamdev umschalten ODER ?

Zitat

Was bleibt ist:

Wenn Streamdev gewinnt erscheint am TV "Stream im Gange". Dann erscheint "Kanal nicht verfügbar".

Aber sollte nicht das LiveTV auf den einzig verfügbaren Kanal = Streamdev =22 = DMAX (oder einen Kanal der Gruppe) wechseln ?

Wenn ich den Stream stoppe läuft LiveTV mit SIXX weiter.

Weist du warum das so ist ?

Ev. kannst du mal bei dir mit 1 Tuner testen ...

Alles anzeigen

HelmutB · 3. April 2021

Das tut es bei mir auch:

Nur 1 Device auf Kanal 7, dann umschalten auf 5, 6 und 7 mit Http-Priority 0.

Bei jeder wget Anforderung wird das Bild schwarz mit der Meldung "Streaming active", das kommt das Livebild auf dem neuen Sender - mit der OSD-Meldung "Kanal nicht verfügbar". Nachdem die Anzeige des OSD ausgeblendet wird, ist der neue Sender bis zum nächsten wget ganz normal zu sehen.

Das "Kanal nicht verfügbar"kommt daher, weil der streamdev-server kein Switchchannel() ausführt, sondern die Receiver des Device einfach abklemmt. VDR bemerkt, dass es kein aktives Programm mehr gibt und will wieder auf das letzte ihm bekannten Programm umschalten (sogar 2 mal). Das geht aber nicht weil es entweder auf einem anderen Transponder ist oder weil die Priority des Device von Streamdev-server zu hoch ist.

Das ist vielleicht nicht schon anzusehen, aber ganz normales verhalten. Hier das Syslog auf dem Server. Die "switching to channel.." Meldungen kommen vom VDR.

Spoiler anzeigen

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5445] Streamdev: Accepted new client (HTTP) 10.0.0.5:46076

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5445] GetDevice: ch 5 - candidate dev 1, imp 0CAC6010, ndr 1 Live:0 Prio: 0/-1 Q

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5445] GetDevice: ch 5 - candidate dev 1, imp 0CAC6010, ndr 1 Live:0 Prio: 0/-1

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5508] streamdev-livestreaming thread started (pid=5403, tid=5508, prio=high)

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5507] streamdev-writer thread started (pid=5403, tid=5507, prio=high)

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5483] device 1 TS buffer thread ended (pid=5403, tid=5483)

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5480] buffer stats: 87232 (0%) used

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5480] device 1 receiver thread ended (pid=5403, tid=5480)

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5509] device 1 receiver thread started (pid=5403, tid=5509, prio=high)

Apr 3 14:55:54 gentoo64vdr vdr[5403]: [5510] device 1 TS buffer thread started (pid=5403, tid=5510, prio=high)

Apr 3 14:55:55 gentoo64vdr vdr[5403]: [5403] switching to channel 7 S19.2E-1-1115-13110 (ServusTV Deutschland)

Apr 3 14:55:55 gentoo64vdr vdr[5403]: [5403] buffer stats: 0 (0%) used

Apr 3 14:55:55 gentoo64vdr vdr[5403]: [5403] switching to channel 5 S19.2E-1-1079-28007 (3sat)

Apr 3 14:55:55 gentoo64vdr vdr[5403]: [5403] GetDevice: ch 5 - candidate dev 1, imp 148C8000, ndr 0 Live:1 Prio: 0/0

Apr 3 14:55:55 gentoo64vdr vdr[5403]: [5403] info: Streaming active

Apr 3 14:55:57 gentoo64vdr vdr[5403]: [5403] info: Kanal nicht verfügbar!

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5445] client (HTTP) 10.0.0.5:46076 has closed connection

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5445] streamdev-server: closing HTTP connection to 10.0.0.5:46076

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5508] streamdev-livestreaming thread ended (pid=5403, tid=5508)

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5507] streamdev-writer thread ended (pid=5403, tid=5507)

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5445] buffer stats: 149648 (3%) used

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5445] Streamdev: Accepted new client (HTTP) 10.0.0.5:46078

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5445] GetDevice: ch 6 - candidate dev 1, imp 0CAC6010, ndr 1 Live:0 Prio: 0/-1 Q

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5445] GetDevice: ch 6 - candidate dev 1, imp 0CAC6010, ndr 1 Live:0 Prio: 0/-1

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5513] streamdev-livestreaming thread started (pid=5403, tid=5513, prio=high)

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5512] streamdev-writer thread started (pid=5403, tid=5512, prio=high)

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5510] device 1 TS buffer thread ended (pid=5403, tid=5510)

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5509] buffer stats: 149272 (0%) used

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5509] device 1 receiver thread ended (pid=5403, tid=5509)

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5514] device 1 receiver thread started (pid=5403, tid=5514, prio=high)

Apr 3 14:56:04 gentoo64vdr vdr[5403]: [5515] device 1 TS buffer thread started (pid=5403, tid=5515, prio=high)

Apr 3 14:56:05 gentoo64vdr vdr[5403]: [5403] switching to channel 5 S19.2E-1-1079-28007 (3sat)

Apr 3 14:56:05 gentoo64vdr vdr[5403]: [5403] buffer stats: 0 (0%) used

Apr 3 14:56:05 gentoo64vdr vdr[5403]: [5403] switching to channel 6 S19.2E-1-1051-28724 (arte)

Apr 3 14:56:05 gentoo64vdr vdr[5403]: [5403] GetDevice: ch 6 - candidate dev 1, imp 148C8000, ndr 0 Live:1 Prio: 0/0

Apr 3 14:56:05 gentoo64vdr vdr[5403]: [5403] info: Streaming active

Apr 3 14:56:07 gentoo64vdr vdr[5403]: [5403] info: Kanal nicht verfügbar!

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5445] client (HTTP) 10.0.0.5:46078 has closed connection

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5445] streamdev-server: closing HTTP connection to 10.0.0.5:46078

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5513] streamdev-livestreaming thread ended (pid=5403, tid=5513)

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5512] streamdev-writer thread ended (pid=5403, tid=5512)

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5445] buffer stats: 139684 (3%) used

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5445] Streamdev: Accepted new client (HTTP) 10.0.0.5:46080

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5445] GetDevice: ch 7 - candidate dev 1, imp 0CAC6010, ndr 1 Live:0 Prio: 0/-1 Q

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5445] GetDevice: ch 7 - candidate dev 1, imp 0CAC6010, ndr 1 Live:0 Prio: 0/-1

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5517] streamdev-writer thread started (pid=5403, tid=5517, prio=high)

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5518] streamdev-livestreaming thread started (pid=5403, tid=5518, prio=high)

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5515] device 1 TS buffer thread ended (pid=5403, tid=5515)

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5514] buffer stats: 139308 (0%) used

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5514] device 1 receiver thread ended (pid=5403, tid=5514)

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5519] device 1 receiver thread started (pid=5403, tid=5519, prio=high)

Apr 3 14:56:14 gentoo64vdr vdr[5403]: [5520] device 1 TS buffer thread started (pid=5403, tid=5520, prio=high)

Apr 3 14:56:15 gentoo64vdr vdr[5403]: [5403] switching to channel 6 S19.2E-1-1051-28724 (arte)

Apr 3 14:56:15 gentoo64vdr vdr[5403]: [5403] buffer stats: 0 (0%) used

Apr 3 14:56:15 gentoo64vdr vdr[5403]: [5403] switching to channel 7 S19.2E-1-1115-13110 (ServusTV Deutschland)

Apr 3 14:56:15 gentoo64vdr vdr[5403]: [5403] GetDevice: ch 7 - candidate dev 1, imp 148C8000, ndr 0 Live:1 Prio: 0/0

Apr 3 14:56:15 gentoo64vdr vdr[5403]: [5403] info: Streaming active

Apr 3 14:56:17 gentoo64vdr vdr[5403]: [5403] info: Kanal nicht verfügbar!

Apr 3 14:56:24 gentoo64vdr vdr[5403]: [5445] client (HTTP) 10.0.0.5:46080 has closed connection

Apr 3 14:56:24 gentoo64vdr vdr[5403]: [5445] streamdev-server: closing HTTP connection to 10.0.0.5:46080

Apr 3 14:56:24 gentoo64vdr vdr[5403]: [5518] streamdev-livestreaming thread ended (pid=5403, tid=5518)

Apr 3 14:56:24 gentoo64vdr vdr[5403]: [5517] streamdev-writer thread ended (pid=5403, tid=5517)

Apr 3 14:56:24 gentoo64vdr vdr[5403]: [5445] buffer stats: 94564 (2%) used

LG Helmut

[gelöst] Streamdev - Prioritäten richtig setzen um LiveTv und Recordings zu bevorzugen

Jetzt mitmachen!

Teilen