[GELÖST] Tasteneingabe bleibt in Verbindung mit einer Harmony Fernbedienung und dem PS3 Remote Profil sporadisch hängen

  • Hol dir mal die build-Dependencies für bluez4:

    Code
    sudo apt-get build-dep bluez

    yaVDR-Dokumentation (Ceterum censeo enchiridia esse lectitanda.)

  • Hi,

    super! Jetzt ist es durchgelaufen.

    Und es funktioniert jetzt auch mit dem Standby! :thumbup:


    Muss ich jetzt noch etwas hierfür tun?

    Zitat

    16. The bluetooth stack is smart enough to terminate the bluetooth connection if the bluetooth service is stopped cleanly when the box is shut down. The connection is terminated if you issue sudo kill <bluetooth process ID> but if you issue sudo kill <b>-9</b> <bluetooth process ID> the connection is left open. (In fact the only way I could make the connection work again after issuing a kill -9 was by taking the batteries out of the PS3 remote control for a few seconds.) So it's worth ensuring that the bluetooth daemon is always shut down cleanly. (If there is a power failure while the bluetooth connection is operating, it's likely that the bluetooth connection will not have been terminated, so it would be worth removing the batteries from the PS3 remote control for a few seconds to prevent them from going flat.)


    Was passiert mit dem Dienst im S3 Modus?


    EDIT: Ich sehe gerade, in "/etc/pm/config.d/20bluetooth" existiert die Zeile:

    SUSPEND_MODULES="btusb"


    Reicht das wohl schon, oder soll ich das bluetooth noch mit dabei schreiben?


    EDIT2: Damit die PS3-Remote nach einem Ruhezustand noch das richtige Mapping aufweist, mussten noch folgende Änderung in der "/etc/default/acpi-support" erfolgen:

    Code
    # Add modules to this list to have them removed before suspend and reloaded
    # on resume. An example would be MODULES="em8300 yenta_socket"
    #
    # Note that network cards and USB controllers will automatically be unloaded
    # unless they're listed in MODULES_WHITELIST
    MODULES="bluetooth"

    ASUS M4A78LT-M GL | AMD Athlon II X2 250 | 2GB RAM | Asus ENGT430 | Digital Devices OctopusNet mit 2 x Digital Devices DuoFlex S2 | PS3Remote | yaVDR 0.6.1

    3 Mal editiert, zuletzt von BOP ()

  • Ach ja, würdest Du mir den Gefallen tun und meinen Fauxpas ausgleichen, den Thread hier gekapert zu haben, indem Du die letzten Posts, die nicht zum eigentlichen Thema gehören, in einen eigenen Thread auslagerst!?

    Dann findet man das hier auch schneller wieder.

    ASUS M4A78LT-M GL | AMD Athlon II X2 250 | 2GB RAM | Asus ENGT430 | Digital Devices OctopusNet mit 2 x Digital Devices DuoFlex S2 | PS3Remote | yaVDR 0.6.1

    Einmal editiert, zuletzt von BOP ()

  • Hi,


    ich benötige noch einmal Hilfe. Nachdem ich mich jetzt seit der Änderung wundere, warum unter Kodi die Menütaste in einer Dauerschleife hängt, nachdem man sie gedrückt hat, bis man eine andere Taste drückt, habe ich heute mal irw gestartet. Und dort sieht man es ebenfalls:

    Woran liegts?

    ASUS M4A78LT-M GL | AMD Athlon II X2 250 | 2GB RAM | Asus ENGT430 | Digital Devices OctopusNet mit 2 x Digital Devices DuoFlex S2 | PS3Remote | yaVDR 0.6.1

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!