Hallo,
ist für obige Karte der Treiber schon im aktuellen 3.10.2 Kernel enthalten? Welche Module muß ich laden?
Habe folgende Karte:
Code
- 02:00.0 Multimedia controller: Digital Devices GmbH Octopus LE DVB adapter
- Subsystem: Digital Devices GmbH Device 0021
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0, Cache Line Size: 64 bytes
- Interrupt: pin A routed to IRQ 16
- Region 0: Memory at f7b00000 (64-bit, non-prefetchable) [size=64K]
- Capabilities: [50] Power Management version 3
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
- Capabilities: [70] MSI: Enable- Count=1/2 Maskable- 64bit+
- Address: 0000000000000000 Data: 0000
- Capabilities: [90] Express (v2) Endpoint, MSI 00
- DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
- ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
- MaxPayload 128 bytes, MaxReadReq 512 bytes
- DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 <1us
- ClockPM- Surprise- LLActRep- BwNot-
- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
- DevCap2: Completion Timeout: Range A, TimeoutDis+, LTR-, OBFF Not Supported
- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
- Compliance De-emphasis: -6dB
- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
- Capabilities: [100 v1] Vendor Specific Information: ID=0000 Rev=0 Len=00c <?>
- Kernel driver in use: DDBridge
- Kernel modules: ddbridge
Wenn ich den ngene Treiber lade erschein im Syslog nur:vdr-server kernel: nGene PCIE bridge driver, Copyright (C) 2005-2007 Micronas
Aber die notwendigen dvb Devices werden nicht angelegt.
Woran liegt das?
Unter /lib/firmware habe ich die ngene_18.fw Datei.
