Hallo,
ich wollte heute erstmals meinen VDR aus Suspend to RAM per Wake on LAN wecken aber bisherige Versuche blieben erfolglos. Wake on Lan funktioniert im ausgeschaltetem Zustand problemlos. Das Ubuntu Wiki zu WoL hab ich auch schon gelesen und versucht auzuwenden, bisher leider ohne Erfolg.
Code
mario@Mario:~$ cat /proc/acpi/wakeup
Device S-state Status Sysfs node
PCI0 S5 *enabled no-bus:pci0000:00
USB0 S3 *enabled pci:0000:00:03.0
USB1 S3 *enabled pci:0000:00:03.1
USB2 S3 *disabled
USB3 S3 *enabled pci:0000:00:03.3
AMR0 S4 *disabled
HDA0 S5 *disabled
UAR1 S5 *disabled pnp:00:07Code
mario@Mario:~$ lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 662 Host (rev 01)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS966 [MuTIOL Media IO] (r ev 59)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 IDE Controller (rev 01)
00:03.0 USB controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.3 USB controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mo de (rev 02)
00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:0b.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
00:0c.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
00:0e.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139 C+ (rev 10)
01:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce 8400 GS] (rev a1)Code
mario@Mario:~$ sudo ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 32
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yesdie Datei /etc/init.d/halt steht auf STOP_SERVICES="networking" und in /etc/init.d/halt habe ich NETDOWN=yes in NETDOWN=no geändert. Trotzdem kein WoL aus S3, hab ich etwas übersehen?
Mario