Zweite SAT-Karte wird nicht verwendet (?)

WebWusel · 25. Januar 2012

Jetzt habe ich gerade ein Problem entdeckt - ich weiß nicht, wonach ich suchen soll, darum beschreibe ich es hier. (Google: [vdr zweite DVB Karte wird nicht erkannt "Nova HD S2"] u. ä. Suche hat mich in meiner akuten Not nicht weiter gebracht)

Es scheint, als ob nur eine der beiden verbauten Nova-HD-S2 genutzt werden. Aufgefallen ist mir das, als ich einen Timerkonflikt erhielt. Daraufhin habe ich eine Live-Aufnahme gestartet und siehe da, ich komme vom Transponder nicht mehr weg.

Soweit ich mich erinnere, wurden unter EasyVDR automatisch alle Karten erkannt - zumindest kann ich mich nicht daran erinnern, dass ich die zweite Karte explizit anmelden musste. Ich kann mich aber auch irren, es lief schließlich jahrelang.

Bitte dringend um Hilfe oder den entscheidenden Hinweis, sonst ist es heute Abend aus mit dem Familienfrieden ...

Hier ein lspci:

Code

01:05.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
01:05.1 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
01:05.2 Multimedia video controller: Device 16f1:8800 (rev 05)
01:05.3 Multimedia controller: Device 16f1:8801 (rev 05)
01:05.4 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)
01:05.6 Multimedia controller: Device 16f1:8804 (rev 05)
01:06.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
01:06.1 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
01:06.2 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
01:06.4 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)

Und noch die Ausgabe von dmesg: (gekürzte Fassung)

Code

[   11.833206] <30>udev[359]: starting version 167
[   11.852939] lp: driver loaded but no devices found
[   11.854636] i2c i2c-0: nForce2 SMBus adapter at 0x2d00
[   11.854641] ACPI: resource nForce2_smbus [io  0x2e00-0x2e3f] conflicts with ACPI region SM00 [io 0x2e00-0x2e3f]
[   11.854643] ACPI: This conflict may cause random problems and system instability
[   11.854644] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   11.854665] i2c i2c-1: nForce2 SMBus adapter at 0x2e00
[   11.869723] asus_atk0110: Resources not safely usable due to acpi_enforce_resources kernel parameter
[   11.873806] Adding 8254460k swap on /dev/sda5.  Priority:-1 extents:1 across:8254460k
[   11.882923] [Firmware Bug]: ACPI(IGPU) defines _DOD but not _DOS
[   11.885870] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:19/LNXVIDEO:00/input/input4
[   11.886508] ACPI: Video Device [IGPU] (multi-head: yes  rom: no  post: no)
[   11.909538] MCE: In-kernel MCE decoding enabled.
[   11.912882] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
[   11.938119] forcedeth 0000:00:0a.0: irq 41 for MSI/MSI-X
[   11.940151] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   11.942800] EDAC MC: Ver: 2.1.0 Jan  3 2012
[   11.958524] EDAC amd64_edac: v3.3.0
[   11.966799] EDAC amd64: DRAM ECC disabled.
[   11.966807] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[   11.966808]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[   11.966809]  (Note that use of the override may cause unknown side effects.)
[   11.982420] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   12.025102] Linux video capture interface: v2.00
[   12.046043] nvidia: module license 'NVIDIA' taints kernel.
[   12.046046] Disabling lock debugging due to kernel taint
[   12.059364] IR NEC protocol handler initialized
[   12.064248] cx88/0: cx2388x v4l2 driver version 0.0.8 loaded
[   12.065846] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.8 loaded
[   12.066493] IR RC5(x) protocol handler initialized
[   12.071352] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 16
[   12.071380] cx8800 0000:01:06.0: PCI INT A -> Link[LNKB] -> GSI 16 (level, low) -> IRQ 16
[   12.072755] cx88[0]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected], frontend(s): 1
[   12.072757] cx88[0]: TV tuner type -1, Radio tuner type -1
[   12.074333] IR RC6 protocol handler initialized
[   12.090111] input: X10 WTI RF receiver as /devices/pci0000:00/0000:00:02.0/usb3/3-2/input/input5
[   12.090198] usbcore: registered new interface driver ati_remote
[   12.090200] ati_remote: 2.2.1:ATI/X10 RF USB Remote Control
[   12.098044] usb 3-2: Weird data, len=1 ff 00 00 00 00 00 ...
[   12.131457] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
[   12.131462] HDA Intel 0000:00:07.0: power state changed by ACPI to D0
[   12.131608] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[   12.131612] HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
[   12.131615] hda_intel: Disable MSI for Nvidia chipset
[   12.131640] HDA Intel 0000:00:07.0: setting latency timer to 64
[   12.132974] cx2388x alsa driver version 0.0.8 loaded
[   12.172753] IR JVC protocol handler initialized
[   12.204134] i2c-core: driver [tuner] using legacy suspend method
[   12.204136] i2c-core: driver [tuner] using legacy resume method
[   12.259143] tveeprom 2-0050: Hauppauge model 69100, rev B4C3, serial# 6535295
[   12.259146] tveeprom 2-0050: MAC address is 00:0d:fe:63:b8:7f
[   12.259148] tveeprom 2-0050: tuner model is Conexant CX24118A (idx 123, type 4)
[   12.259151] tveeprom 2-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
[   12.259153] tveeprom 2-0050: audio processor is None (idx 0)
[   12.259155] tveeprom 2-0050: decoder processor is CX880 (idx 20)
[   12.259156] tveeprom 2-0050: has no radio, has IR receiver, has no IR transmitter
[   12.259158] cx88[0]: hauppauge eeprom: model=69100
[   12.290033] Registered IR keymap rc-rc5-hauppauge-new
[   12.290123] input: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:08.0/0000:01:06.0/rc/rc0/input6
[   12.290179] rc0: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:08.0/0000:01:06.0/rc/rc0
[   12.290223] cx88[0]/0: found at 0000:01:06.0, rev: 5, irq: 16, latency: 32, mmio: 0xf0000000
[   12.290282] cx88[0]/0: registered device video0 [v4l2]
[   12.290308] cx88[0]/0: registered device vbi0
[   12.291853] cx88[1]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected], frontend(s): 1
[   12.291855] cx88[1]: TV tuner type -1, Radio tuner type -1
[   12.326579] RPC: Registered udp transport module.
[   12.326583] RPC: Registered tcp transport module.
[   12.326585] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   12.336192] FS-Cache: Loaded
[   12.350338] FS-Cache: Netfs 'nfs' registered for caching
[   12.372027] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   12.438528] IR Sony protocol handler initialized
[   12.447823] lirc_dev: IR Remote Control driver registered, major 250
[   12.449330] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 20
[   12.449337] nvidia 0000:02:00.0: PCI INT A -> Link[SGRU] -> GSI 20 (level, low) -> IRQ 20
[   12.449344] nvidia 0000:02:00.0: setting latency timer to 64
[   12.449348] vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   12.449825] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  270.41.06  Mon Apr 18 14:53:56 PDT 2011
[   12.452454] rc rc0: lirc_dev: driver ir-lirc-codec (cx88xx) registered at minor = 0
[   12.452456] IR LIRC bridge handler initialized
[   12.456355] tveeprom 3-0050: Huh, no eeprom present (err=-6)?
[   12.456360] tveeprom 3-0050: Hauppauge model 69100, rev B4C3, serial# 6535295
[   12.456363] tveeprom 3-0050: MAC address is 00:0d:fe:63:b8:7f
[   12.456365] tveeprom 3-0050: tuner model is Conexant CX24118A (idx 123, type 4)
[   12.456367] tveeprom 3-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
[   12.456369] tveeprom 3-0050: audio processor is None (idx 0)
[   12.456371] tveeprom 3-0050: decoder processor is CX880 (idx 20)
[   12.456373] tveeprom 3-0050: has no radio, has IR receiver, has no IR transmitter
[   12.456375] cx88[1]: hauppauge eeprom: model=69100
[   12.459601] Registered IR keymap rc-rc5-hauppauge-new
[   12.459736] input: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:08.0/0000:01:05.0/rc/rc1/input7
[   12.459794] rc1: cx88 IR (Hauppauge WinTV-HVR400 as /devices/pci0000:00/0000:00:08.0/0000:01:05.0/rc/rc1
[   12.459894] rc rc1: lirc_dev: driver ir-lirc-codec (cx88xx) registered at minor = 1
[   12.459894] cx88[1]/2: cx2388x 8802 Driver Manager
[   12.460149] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
[   12.460154] cx88-mpeg driver manager 0000:01:05.0: PCI INT A -> Link[LNKA] -> GSI 19 (level, low) -> IRQ 19
[   12.460161] cx88[1]/2: found at 0000:01:05.0, rev: 5, irq: 19, latency: 32, mmio: 0xf4000000
[   12.460255] cx88[0]/2: cx2388x 8802 Driver Manager
[   12.460262] cx88-mpeg driver manager 0000:01:06.2: PCI INT A -> Link[LNKB] -> GSI 16 (level, low) -> IRQ 16
[   12.460267] cx88[0]/2: found at 0000:01:06.2, rev: 5, irq: 16, latency: 32, mmio: 0xf2000000
[   12.462639] input: lircd as /devices/virtual/input/input8
[   12.464202] cx88_audio 0000:01:05.1: PCI INT A -> Link[LNKA] -> GSI 19 (level, low) -> IRQ 19
[   12.464227] cx88[1]/1: CX88x/0: ALSA support for cx2388x boards
[   12.464503] cx88_audio 0000:01:06.1: PCI INT A -> Link[LNKB] -> GSI 16 (level, low) -> IRQ 16
[   12.464519] cx88[0]/1: CX88x/1: ALSA support for cx2388x boards
[   12.474532] cx88/2: cx2388x dvb driver version 0.0.8 loaded
[   12.474535] cx88/2: registering cx8802 driver, type: dvb access: shared
[   12.474539] cx88[1]/2: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69]
[   12.474541] cx88[1]/2: cx2388x based DVB/ATSC card
[   12.474543] cx8802_alloc_frontends() allocating 1 frontend(s)
[   12.476975] cx24116_readreg: reg=0xff (error=-6)
[   12.477612] cx24116_readreg: reg=0xfe (error=-6)
[   12.477614] Invalid probe, probably not a CX24116 device
[   12.477670] cx88[1]/2: frontend initialization failed
[   12.477672] cx88[1]/2: dvb_register failed (err = -22)
[   12.477674] cx88[1]/2: cx8802 probe failed, err = -22
[   12.477676] cx88[0]/2: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69]
[   12.477679] cx88[0]/2: cx2388x based DVB/ATSC card
[   12.477680] cx8802_alloc_frontends() allocating 1 frontend(s)
[   12.482255] DVB: registering new adapter (cx88[0])
[   12.482260] DVB: registering adapter 0 frontend 0 (Conexant CX24116/CX24118)...
[   12.600338] input: eventlircd as /devices/virtual/input/input9
[   13.021842] svc: failed to register lockdv1 RPC service (errno 97).
[   13.021896] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   13.022224] NFSD: starting 90-second grace period
[   13.180417] input: eventlircd as /devices/virtual/input/input10
[   18.489427] cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)...
[   18.505078] cx24116_firmware_ondemand: Waiting for firmware upload(2)...
[   22.700029] eth0: no IPv6 routers present
[   23.830714] cx24116_load_firmware: FW version 1.26.90.0
[   23.830738] cx24116_firmware_ondemand: Firmware upload complete

Alles anzeigen

Generador · 25. Januar 2012

Du kannst soweit ich weiss in den Settings vom VDR einstellen wieviel DVB Karten vorhanden sind bzw. die LNB Settings überprüfen ob vielleicht beide Karten auf LNB1 stehen

steffen_b · 25. Januar 2012

Ist das alles an Log oder kommt da noch mehr ? In dem Log wird nur eine Karte geladen vom Kernel. Ist das bei jedem Boot so ? Gibts noch mehr Meldungen ?

Eigentlich muss man garnichts machen und es geht einfach - Auch sollte es egal sein wann die Karte endlich fertig ist weil da kümmert sich das dynamite Plugin drum.

Denkbar wären Timingprobleme wenn die Karten gleichzeitig initialisert werden (zB Treiberprobleme) oder ..

seahawk1986 · 25. Januar 2012

Zitat von WebWusel

Code

[   12.477614] Invalid probe, probably not a CX24116 device
[   12.477670] cx88[1]/2: frontend initialization failed

Da ist das Problem, was die Ursache ist, weiß ich nicht - evtl. mal Kontakte überprüfen (evtl Steckplatz wechseln) und linux-media-dkms installieren.

Face · 25. Januar 2012

Ich hab hier ein ähnliches Problem - 3 Karten zwei Aufnahmen kein Live mehr nur noch auf Aufnahme Transponder. Hatte leider noch keine Zeit mich darum zu kümmern - ich dachte da mach ich wenn die vierte Karte rein kommt.

hwinfo --pci:

Code

28: PCI 108.0: 11200 TV Card
  [Created at pci.318]
  Unique ID: 75Hn.u5MUJIDyx25
  Parent ID: WL76.vuIf6LvchL4
  SysFS ID: /devices/pci0000:00/0000:00:09.0/0000:01:08.0
  SysFS BusID: 0000:01:08.0
  Hardware Class: tv card
  Model: "Conexant CX23880/1/2/3 PCI Video and Audio Decoder"
  Vendor: pci 0x14f1 "Conexant Systems, Inc."
  Device: pci 0x8800 "CX23880/1/2/3 PCI Video and Audio Decoder"
  SubVendor: pci 0x0070 "Hauppauge computer works Inc."
  SubDevice: pci 0x6906
  Revision: 0x05
  Driver: "cx8800"
  Driver Modules: "cx8800"
  Memory Range: 0xf8000000-0xf8ffffff (rw,non-prefetchable)
  IRQ: 18 (26303251 events)
  Module Alias: "pci:v000014F1d00008800sv00000070sd00006906bc04sc00i00"
  Driver Info #0:
	Driver Status: cx8800 is active
	Driver Activation Cmd: "modprobe cx8800"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #17 (PCI bridge)


29: PCI 108.1: 0480 Multimedia controller
  [Created at pci.318]
  Unique ID: _Pmc.INamA9r_vg1
  Parent ID: WL76.vuIf6LvchL4
  SysFS ID: /devices/pci0000:00/0000:00:09.0/0000:01:08.1
  SysFS BusID: 0000:01:08.1
  Hardware Class: unknown
  Model: "Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port]"
  Vendor: pci 0x14f1 "Conexant Systems, Inc."
  Device: pci 0x8811 "CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port]"
  SubVendor: pci 0x0070 "Hauppauge computer works Inc."
  SubDevice: pci 0x6906
  Revision: 0x05
  Driver: "cx88_audio"
  Driver Modules: "cx88_alsa"
  Memory Range: 0xfb000000-0xfbffffff (rw,non-prefetchable)
  IRQ: 18 (26303251 events)
  Module Alias: "pci:v000014F1d00008811sv00000070sd00006906bc04sc80i00"
  Driver Info #0:
	Driver Status: cx88_alsa is active
	Driver Activation Cmd: "modprobe cx88_alsa"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #17 (PCI bridge)


30: PCI 108.2: 0480 Multimedia controller
  [Created at pci.318]
  Unique ID: rkFS.Z9QXzb3Q0xB
  Parent ID: WL76.vuIf6LvchL4
  SysFS ID: /devices/pci0000:00/0000:00:09.0/0000:01:08.2
  SysFS BusID: 0000:01:08.2
  Hardware Class: unknown
  Model: "Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port]"
  Vendor: pci 0x14f1 "Conexant Systems, Inc."
  Device: pci 0x8802 "CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port]"
  SubVendor: pci 0x0070 "Hauppauge computer works Inc."
  SubDevice: pci 0x6906
  Revision: 0x05
  Driver: "cx88-mpeg driver manager"
  Driver Modules: "cx8802"
  Memory Range: 0xfa000000-0xfaffffff (rw,non-prefetchable)
  IRQ: 18 (26303251 events)
  Module Alias: "pci:v000014F1d00008802sv00000070sd00006906bc04sc80i00"
  Driver Info #0:
	Driver Status: cx8802 is active
	Driver Activation Cmd: "modprobe cx8802"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #17 (PCI bridge)

Alles anzeigen

dmesg | grep -i dvb

Code

[   15.852792] saa7146: register extension 'budget_ci dvb'
[   15.871130] budget_ci dvb 0000:01:09.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
[   15.871136] budget_ci dvb 0000:01:09.0: setting latency timer to 64
[   15.871194] DVB: registering new adapter (TT-Budget S2-3200 PCI)
[   15.990358] input: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:09.0/0000:01:09.0/rc/rc0/input2
[   15.990432] rc0: Budget-CI dvb ir receiver saa7146 (0) as /devices/pci0000:00/0000:00:09.0/0000:01:09.0/rc/rc0
[   16.796527] DVB: registering adapter 0 frontend 0 (STB0899 Multistandard)...
[   16.800491] DVB: registering new adapter (KNC TV STAR DVB-S)
[   19.548091] cx88[0]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected], frontend(s): 1
[   19.752983] tveeprom 4-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
[   19.854917] cx88/2: cx2388x dvb driver version 0.0.9 loaded
[   19.854923] cx88/2: registering cx8802 driver, type: dvb access: shared
[   19.854928] cx88[0]/2: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69]
[   19.854933] cx88[0]/2: cx2388x based DVB/ATSC card
[   19.882963] DVB: registering new adapter (cx88[0])
[   19.882969] DVB: registering adapter 2 frontend 0 (Conexant CX24116/CX24118)...
[  194.876237] cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)...

Alles anzeigen

Deshalb lese und teste ich mal mit.

WebWusel · 25. Januar 2012

Danke für die Antworten,

inzwischen bin ich selbst auf die Idee gekommen, den Steckplatz zu wechseln und das führte zum Erfolg! Jetzt laufen beide Karten.

Zum einen fand ich die Ausgabe von lspci etwas merkwürdig denn es hätten beide Karten auf verschiedenen Steckplätzen gelistet werden müssen. Stattdessen wurden teile der zweiten Karte so gelistet, als ob sie auch auf dem Steckplatz der ersten Karte stecken.

Außerdem ist mir dann noch das hier aufgefallen:

Code

[	0.910208] pci 0000:01:05.2: address space collision: [mem 0xf4000200-0xf40003ff] conflicts with 0000:01:05.0 [mem 0xf4000000-0xf4ffffff]
[	0.910208] pci 0000:01:05.3: address space collision: [mem 0xf5000200-0xf50003ff] conflicts with 0000:01:05.1 [mem 0xf5000000-0xf5ffffff]
[	0.910208] pci 0000:01:05.6: address space collision: [mem 0xf8000200-0xf80003ff] conflicts with 0000:01:05.4 [mem 0xf8000000-0xf8ffffff]
[	0.953192] pci 0000:01:05.2: BAR 0: assigned [mem 0xf6000000-0xf60001ff]
[	0.953197] pci 0000:01:05.2: BAR 0: error updating (0xf6000000 != 0xf6000200)
[	0.953199] pci 0000:01:05.2: BAR 0: set to [mem 0xf6000000-0xf60001ff] (PCI address [0xf6000000-0xf60001ff])
[	0.953202] pci 0000:01:05.3: BAR 0: assigned [mem 0xf6000200-0xf60003ff]
[	0.953206] pci 0000:01:05.3: BAR 0: set to [mem 0xf6000200-0xf60003ff] (PCI address [0xf6000200-0xf60003ff])
[	0.953209] pci 0000:01:05.6: BAR 0: assigned [mem 0xf6000400-0xf60005ff]
[	0.953212] pci 0000:01:05.6: BAR 0: error updating (0xf6000400 != 0xf6000200)
[	0.953214] pci 0000:01:05.6: BAR 0: set to [mem 0xf6000400-0xf60005ff] (PCI address [0xf6000400-0xf60005ff])

Alles anzeigen

Das war nicht schön.

lspci sieht jetzt deutlich besser aus:

Code

01:06.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
01:06.1 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
01:06.2 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
01:06.4 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)
01:07.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
01:07.1 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
01:07.2 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
01:07.4 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)

steffen_b: Was sollte denn da noch an Logs kommen? Man, man, man ... wie man machts, man macht es falsch.

Dieses Problem ist also gelöst. Zufrieden macht mich das aber nicht, weil ich mir höchstwahrscheinlich die Anschaffung einer dritten SAT-Karte auf diesem Mainboard (Asus M4N78pro) sparen kann.

Schönen Abend noch!

ATD · 25. Januar 2012

Zitat von WebWusel

Was sollte denn da noch an Logs kommen?

Ich denke, das hat Steffen ironisch gemeint.

Albert

Zweite SAT-Karte wird nicht verwendet (?)

Jetzt mitmachen!

Teilen