Am Verzweifeln: PSOne an Matrox G450 DH

  • Hallo Leute,


    jetzt lese ich hier schon Tage im Forum, habe aber immer noch keine Ahnung, wie ich GraphTFT mit meinem PSOne-Display zum Laufen kriegen soll.


    An Hardware habe ich folgendes:
    - Matrox G450 DualHead (16MB)
    - RGB-Adapter
    - Composite-Adapter
    - PSOne-Display / Spannungsversorgung aus Netzteil


    Software
    - LinVDR 0.7 unverbastelte Installation


    Könnte sich jemand erbarmen und mir eine Step-für-Step-Anleitung geben, wie ich das hinbekomme?


    Was muss ich wie noch installieren?


    Mit den Anleitungen für Halbprofis komme ich nicht weiter...


    ThomasG

  • tach,


    also bevor wir starten einige fragen...


    wie schaltest du das Psone an die Matrox an???


    Einfachste Lösung: Composite Video (reicht völlig für das GraphTFT!!!)


    Steckerbelegung der Psone steht im Bedienungshandbuch von sony drin, adapterkabel kann man bei reichelt kaufen, oder man probiert provisorisch mit halbreingestecktem audio-3.5mm-stereo klinke auf 2 mal chinch. meist tuts mit dem roten chinch auf anhieb musste probieren.


    psone muss!! vor dem booten an die matrox angeschlossen werden, denn nur zum bootvorgang erkennt die karte einen angeschlossenen TV-monitor. wenn der nicht da ist, dann wird der tv-out nicht aktiviert. geht dann später auch nicht mehr.


    also dies erstmal machen!


    danach im VDR zunächst...


    VDR stoppen (runvdr stop)
    danach setup aufrufen und das graphtft aktivieren, wenn noch nicht geschehen...
    hier im board nach matroxfb suchen und die werte entsprechend eintragen.



    Gruss


    Adama ;)

  • Hallo Adama,


    ich habe es bisher so probiert:


    -> PSOne an Compositeadapter
    -> danach Rechner booten


    Resultat:
    Das Display schaltet sich ein (d.h. irgendein Signal liegt wohl an). Es wird aber kein Bild angezeit. Die Parameter stimmen scheinbar nicht.


    Wenn ich GraphTFT aktiviere, bootet der VDR zwar noch, aber am TV geht nichts mehr.


    ThomasG

  • sieht so aus, dass du den Ausgang des GraphTFT auf der DVB-Karte liegt. Da musser wech.
    Du muss es hinkriegen, dem GraphTFT mitzuteilen, dass du die Ausgabe über Framebuffer (matroxfb) haben möchtest, dann schaltet das plugin die Ausgabe auf die Graka um.


    Gruss


    Adama ;)

  • hier mal lesen:


    http://www.vdr-wiki.de/wiki/index.php/Graphtft-plugin


    dann die doku vom plugin durchackern. Es sind die parameter die du einstellen musst. Aber ich kann hier keine Fernheilung machen, denn ich weiss ja nix von deinem system ausser dass du ne matrox hast. und die ist so ziemlich die einfachste aller nur denkbaren lösungen.


    nix für ungut!


    Adama ;)


    edit on //


    hier die INSTALL vom plugin:


    Install the grapftft Plugin:


    1. Copy the graphtft-0.0.x directory to your VDR/PLUGINS/src directory.


    2. Make a graphtft link to the graphtft-0.0.x directory
    (i.e " ln -s graphtft-0.0.x graphtft ")


    3. For DVB/FB-Output:

    Make sure you have Imlib2 correct installed on your system:
    Try 'imlib2-config --libs' on the console, an Imlib2.h shoud be in your includes.


    For directFB-Output:


    Make sure you have directFB and libsoftmpeg correct installed on your system.
    For now you have to use the CVS versions.


    4. Make sure you have ffmpeg-0.4.8 (include the sources!!!) correct installed on your system.
    (we'll need the libavcodec subdir)


    5. Change the Path to ffmpeg in the Makefile, and set configuration options:
    (i.e. use "vi Makefile" or what editor you else able to use ;)


    6. Copy the underdirectory graphTFT to your VDR-Config direction in the plugins dir.
    (i.e. "cp -rf graphTFT <VDR-Config>/plugins"). If you won't copy tree empty dir, you can
    create the directory structure by your own)


    7. Load the last standard theme from wwwmath.upb.de/~tegeler/vdr/graphtft
    and extract it to the <VDR-Config>/plugins/graphTFT/themes directory (this is one of the dirs we created in 6.)

    8. You'll need true type fonts in the <VDR-Config>/plugins/graphTFT/fonts dir. To use the Standard Theme make
    sure you have Vera.ttf(use google or look on your system and you will find it). For other Themes may be other
    Fonts are needed.


    9. Build the VDR Plugins( with 'make plugins', I think you know it allready *g*)


    10.Now you can run your VDR i.e. with the Option " -P'graphtft -d /dev/fb0' " for Framebuffer use,
    or " -P'graphtft -d vdr/1 ' " to use the FF-VDR-Device (in this case the second, we count from zero,
    but this is often the primary device...) or " -P'graphtft -d directFB' " for Framebuffer with directFB.



    Punkt 10 ist dein Freund!!!


    edit off //

  • Zitat

    Original von Adama


    For directFB-Output:


    Make sure you have directFB and libsoftmpeg correct installed on your system.
    For now you have to use the CVS versions.


    Ich denke, da liegt das Problem.


    Ich habe eine Standardinstallation des LinVDR 0.7 auf meinem PC. Ich hab' keine Ahnung, ob da nun directfb drauf ist oder nicht. Egal, in meinem Fall ist da wohl matroxfb angesagt, richtig?


    Mein nächster Schritt wird dann also die Installation von matroxfb. Kann mir jemand kurz erklären, wie ich das machen soll? Stundenlange Recherchen im WWW haben mich da nicht wirklich schlauer gemacht ;(


    ThomasG

  • Hallo -
    also, ich hatte mal eine G400DH und wenn dort der zweite Monitorausgang im Clone-Modus was darstellen sollte, brauchte man den entsprechenden LinuxTreiber für X11. Automatisch war da nix zu sehen.
    Dies betraf auch die Ausgabe auf den Video-Out.
    Ich habe allerdings nie LinVDR hiermit benutzt. Was ich getan habe, war eine "normale" Suse-Distri, dann die VDR Software entsprechend kompiliert. Den VideoOut habe ich zur Darstellung von der K-GUI auf den Video-Ausgang ( im Clone Modus ) genutzt um auf dem Fernseher zu surfen. Da aber die Maus nicht dargestellt worden ist und sich Matrox außerstande sah, dies zu beheben, habe ich dies dann seingelassen.


    Ronald

    LinVDR0.7+MT-Patch+Cody Patch1.3.27/AMD700/MP3/GraphLCD - SED1330/MDFHolzkiste - die berühmte Schwarze Kiste/2 rote LED/ EinAusSchalter/integrierte Kochplatte/:vdr1

  • Hi,
    was in linvdr so alles vorhanden ist, weiss ich nicht, doch da ich gerade auch etwas am framebuffer fuer die G450 am herumbasteln bin:
    Schau bei http://www.bglug.ca/matrox_tvout/g450_tvout_howto.html vorbei.
    FBAS geht bei der Matrox nur ueber /dev/fb1, welches vorher richtig konfiguriert werden muss (das PSOne "macht" ja m.W. NTSC) ...
    Probiere dann einfach mal mit mplayer (ganz ohne VDR und auf der Konsole) diverse mpegs (koennen natuerlich auch vdr-files sein) auf dem Display abzuspielen und passe mit fbset das Ganze an (Bildqualitaet ist bei mir uebrigens keineswegs - aber nicht am PSOne, da ich keines habe :D - wirklich berauschend) ...
    Gruss
    Burkhardt

  • Ja,


    das PSOne läuft nun wie gewünscht.


    Angeschlossen am TV-Out (Composite-Signal) an einer alten GeForce MX440 oder so ähnlich.


    Ich habe lediglich noch einen ca. 8mm breiten Rand. Wäre schön, wenn ich die Fläche auch noch mitbenutzen könnte. Das Ändern der Auflösung im Setup hat kaum eine Besserung gebracht.


    Ich werde deswegen nochmal meine Matrox 450 einbauen. Vielleicht ist der Rand ja dann weg. Ansonsten muss ich wohl mal mit modelines spielen...


    ThomasG

  • Ich kann jetzt mur für meine G550 sprechen, aber die schaltet noch nicht einmal den TV-Out an, wenn der PC bootet. Die muß schon Softwaremäßig umgeschaltet werden.
    Ich habe mir jetzt für das PSone TFT auch einfach bei eBay für 20 Euro eine GForce2 MX GraKa von Asus geholt. Damit läuft das PSOne TFT.
    Natürlich auch nur mit den Rändern. Da wird man aber nichts dran ändern können. Also zumindest nicht mit LinVDR.
    Das stört mich aber auch nicht weiter. Bei GraphTFT find ichs nicht so schlimm.


    Gruß

    ASUS M4A78LT-M GL | AMD Athlon II X2 250 | 2GB RAM | Asus ENGT430 | Digital Devices OctopusNet mit 2 x Digital Devices DuoFlex S2 | PS3Remote | yaVDR 0.6.1

    Einmal editiert, zuletzt von BOP ()

  • Hallo,
    wie Thomas habe ich ein PSOne Display an Video Out einer Geforce II angeschlossen. Allerdings "läuft" das Bild und wird auch nur monochrom dargestellt. Ein angeschlossener Fernseher liefert ein sauberes, aber ebenfalls monochromes Bild. Hat jemand eine Idee wie das unter Linvdr zu beheben ist?
    Gruß
    Bruno

  • hi,


    bei mir das gleiche problem: ich bekomme mit einer geforce2 mx440 nur ein laufendes (flackerndes, absolut unlesbares) bild auf dem psone-tft, auf dem fernseher sieht die ausgabe des graphtft-plugins oder einer einfachen textconsole super aus.


    wegen dem monochrom am tv: das kann am tv liegen, hier evtl an den einstellungen des fernsehers spielen...


    was uns aber nix bringt, schließlich wollen wir das bild ja auf dem psone-tft....


    jemand eine idee??


    gruß micrix

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!