Ahhhh, NUR HD Kanäle, warum ?? ;(

hallo,

ja ich kenn auch solche Probleme mit Tevii Karten.

Hab eine 464 und eine 470.

Bekomme bei mehreren Sendern kein Bild, und die Meldung

"Kanal nicht verfügbar"

finde leider keine Lösung

MfG

avalanche99

Karte sicher nicht defekt, da ich es auch mit der S464 hab, und jetzt auf 0.3 sind es bei mir alle Sender, bei 0.2 waren es nur verschiedene.

Aber eine Lösung finde ich nirgens im Internet, und auch im Forum nicht.

Be mir hat es auch 2 mal gekalppt, seit dem nicht mehr!

Bin am verzweifeln und denke wirklich darüber nach die Hardware zu verkaufen und mir eine AZBox oder eine Dreambox, oder VU+ Set-top-Box zu kaufen

Nabend,

bei den Tevii-Karten empfiehlt es sich immer die passenden Pakete/Treiber von deren Webseite zu nehmen:

http://www.tevii.com/Support.asp

In den Paketen ist die jeweils aktuelle Firmware und die dazu passenden aktuellen Linuxtreiber.

Beide Karten (470er/464er) sind mit den Paketen lauffähig und äusserst stabil.

PS: Mit dem Kauf eines Receivers holst du dir halt andere Probleme ins Haus die du bei weitem nicht so einfach lösen kannst...

Gruß
Wolfgang

Installieren immer die Treiber von der Webseite von Tevii,

gehe nach folgender Anleitung vor:

sudo wget http://www.tevii.com/100315_Beta_linux_tevii_ds3000.rar
sudo unrar e 100315_Beta_linux_tevii_ds3000.rar
sudo cp *.fw /lib/firmware
sudo tar xjvf linux-tevii-ds3000.tar.bz2
cd linux-tevii-ds3000
sudo make
sudo make install

Aber mit einer Set-Top-Box hab man wenigstens ein Bild un kann kucken, hier nie!!! Was soll ich den mehr wollen von einem Sat-Receiver als Bild?

Bin wirklich soweit dass ich das ganz Projekt aufgeben möchte, leider war die Hardware teuer und weiss nicht was damit tun, mit dickem Verlust verkaufen bringt auch nichts!

MfG

avalanche99

Zitat

Original von avalanche99

Aber mit einer Set-Top-Box hab man wenigstens ein Bild un kann kucken, hier nie!!! Was soll ich den mehr wollen von einem Sat-Receiver als Bild?

Bin wirklich soweit dass ich das ganz Projekt aufgeben möchte, leider war die Hardware teuer und weiss nicht was damit tun, mit dickem Verlust verkaufen bringt auch nichts!

MfG

avalanche99

Alles anzeigen

Naja,

wenn du keine Nvidia/vdpau-fähige Grafikkarte hast, dann ist Handarbeit angesagt und das ist nicht einfach...

Soweit ich das sehe hast du keine solche Karte, zmindest laut Signatur.

Gruß
Wolfgang

Doch Doch, MSI VN210 MD512 H

Eine GT 210 passiv von MSI

Hier die syslog:

Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.045461] cx88[0]: subsystem: d464:9022, board: UNKNOWN/GENERIC [card=0,autodetected], frontend(s): 0
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.045463] cx88[0]: TV tuner type -1, Radio tuner type -1
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.181501] tuner 4-0068: chip found @ 0xd0 (cx88[0])
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.226366] cx88[0]/0: found at 0000:05:06.0, rev: 5, irq: 21, latency: 64, mmio: 0xfd000000
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.226375] IRQ 21/cx88[0]: IRQF_DISABLED is not guaranteed on shared IRQs
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.226457] cx88[0]/0: registered device video0 [v4l2]
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.226489] cx88[0]/0: registered device vbi0
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.226501] tuner 4-0068: tuner type not set
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.454557] lirc_imon: IR port opened
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.968377] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.034747] ACPI: 'UHC1' and 'UHC5' have the same GPE, can't disable/enable one seperately
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.034749] ACPI: 'UHC2' and 'UHC5' have the same GPE, can't disable/enable one seperately
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.034751] ACPI: 'UHC3' and 'UHC5' have the same GPE, can't disable/enable one seperately
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.034753] ACPI: 'USB4' and 'UHC5' have the same GPE, can't disable/enable one seperately
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.034755] ACPI: 'UHC6' and 'UHC5' have the same GPE, can't disable/enable one seperately
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.034756] ACPI: 'UHC7' and 'UHC5' have the same GPE, can't disable/enable one seperately
Oct 19 21:49:19 ubuntu-htpc cron[1214]: (CRON) INFO (pidfile fd = 3)
Oct 19 21:49:19 ubuntu-htpc acpid: starting up with proc fs
Oct 19 21:49:19 ubuntu-htpc acpid: 36 rules loaded
Oct 19 21:49:19 ubuntu-htpc acpid: waiting for events: event logging is off
Oct 19 21:49:19 ubuntu-htpc anacron[1256]: Anacron 2.3 started on 2010-10-19
Oct 19 21:49:19 ubuntu-htpc cron[1261]: (CRON) STARTUP (fork ok)
Oct 19 21:49:19 ubuntu-htpc cron[1261]: (CRON) INFO (Running @reboot jobs)
Oct 19 21:49:19 ubuntu-htpc anacron[1256]: Normal exit (0 jobs run)
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.194360] svc: failed to register lockdv1 RPC service (errno 97).
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.194796] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
Oct 19 21:49:19 ubuntu-htpc kernel: [ 10.195033] NFSD: starting 90-second grace period
Oct 19 21:49:20 ubuntu-htpc anacron[1389]: Anacron 2.3 started on 2010-10-19
Oct 19 21:49:20 ubuntu-htpc anacron[1389]: Normal exit (0 jobs run)
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.942181] CPU0 attaching NULL sched-domain.
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.942185] CPU1 attaching NULL sched-domain.
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.978685] CPU0 attaching sched-domain:
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.978689] domain 0: span 0-1 level MC
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.978693] groups: 0 1
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.978699] CPU1 attaching sched-domain:
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.978701] domain 0: span 0-1 level MC
Oct 19 21:49:20 ubuntu-htpc kernel: [ 10.978703] groups: 1 0
Oct 19 21:49:20 ubuntu-htpc acpid: client connected from 1178[0:0]
Oct 19 21:49:20 ubuntu-htpc acpid: 1 client rule loaded
Oct 19 21:49:21 ubuntu-htpc init: logo-start main process (141cool killed by TERM signal
Oct 19 21:49:21 ubuntu-htpc vdr: [1102] Text2Skin: message display update thread ended (pid=1026, tid=1102)
Oct 19 21:49:21 ubuntu-htpc vdr: [1026] setting watchdog timer to 60 seconds
Oct 19 21:49:21 ubuntu-htpc vdr: [1026] switching to channel 1
Oct 19 21:49:21 ubuntu-htpc vdr: [1026] info: Channel not available!
Oct 19 21:49:21 ubuntu-htpc vdr: [1441] Text2Skin: message display update thread started (pid=1026, tid=1441)
Oct 19 21:49:21 ubuntu-htpc vdr: [1088] [xine..put] Client 0 connected: 127.0.0.1:53434
Oct 19 21:49:21 ubuntu-htpc vdr: [1088] loading /var/lib/vdr/plugins/xineliboutput/allowed_hosts.conf
Oct 19 21:49:21 ubuntu-htpc vdr: [1088] [xine..put] cxSocket: setsockopt(SO_SNDBUF): got 262142 bytes
Oct 19 21:49:21 ubuntu-htpc vdr: [1088] [xine..put] Client connection 0 closed
Oct 19 21:49:21 ubuntu-htpc vdr: [1088] [xine..put] Closing connection 0
Oct 19 21:49:21 ubuntu-htpc vdr-sxfe[1443]: [1443] [vdr-fe] Failed to open connection to bus: /bin/dbus-launch terminated abnormally without any error message
Oct 19 21:49:21 ubuntu-htpc vdr-sxfe[1443]: [1443] [vdr-fe] (ERROR (tools/gnome_screensaver.c,61): No such file or directory)
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [vdr-fe] fe_xine_init: xine_open_audio_driver("alsa") failed
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [vdr-fe] Detected 2 CPUs
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [vdr-fe] Enabling FFmpeg multithreaded video decoding
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [input_vdr] Connecting (control) to tcp://127.0.0.1:37890 ...
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] [xine..put] Client 0 connected: 127.0.0.1:53435
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] loading /var/lib/vdr/plugins/xineliboutput/allowed_hosts.conf
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] [xine..put] cxSocket: setsockopt(SO_SNDBUF): got 262142 bytes
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [input_vdr] Server greeting: VDR-1.7.16 xineliboutput-1.0.90-cvs READY
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [input_vdr] Connected (control) to tcp://127.0.0.1:37890
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] [xine..put] Trying PIPE connection ...
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] creating directory /var/lib/vdr/plugins/xineliboutput/pipes.1026
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [input_vdr] Connecting (data) to pipe:///var/lib/vdr/plugins/xineliboutput/pipes.1026/pipe.0
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] removing /var/lib/vdr/plugins/xineliboutput/pipes.1026
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] [xine..put] cBackgroundWriterI initialized (buffer 512 kb)
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] [xine..put] cTcpWriter initialized (buffer 512 kb)
Oct 19 21:49:22 ubuntu-htpc vdr: [1088] [xine..put] Pipe open
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [input_vdr] Data stream connected (PIPE)
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [input_vdr] WARNING: xine-engine setting "engine.buffers.audio_num_buffers":0 istoo low for HD-playback! Please use values between 500-1000!
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [input_vdr] using custom "no signal" image /usr/share/libxine1-xvdr/nosignal.mpg
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [demux_vdr] Using decoder "libmpeg2" for mpeg2 video
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1443] [demux_vdr] Using decoder "FFmpeg" for H.264 video
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1455] [vdr-fe] Can't load post plugin goom
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1457] [vdr-fe] read_key: read(stdin) failed: no stdin
Oct 19 21:49:22 ubuntu-htpc vdr-sxfe[1443]: [1457] [vdr-fe] Keyboard thread terminated
Oct 19 21:49:23 ubuntu-htpc vdr: [1441] Text2Skin: message display update thread ended (pid=1026, tid=1441)
Oct 19 21:49:23 ubuntu-htpc vdr: [1026] OSD size changed to 1920x1080 @ 1
Oct 19 21:49:23 ubuntu-htpc vdr: [1026] max. latency time 2 seconds
Oct 19 21:49:23 ubuntu-htpc vdr: [1465] Text2Skin: channelInfo display update thread started (pid=1026, tid=1465)
Oct 19 21:49:24 ubuntu-htpc vdr: [1086] EPGSearch: timer conflict check started
Oct 19 21:49:24 ubuntu-htpc vdr: [1086] EPGSearch: timer conflict check finished
Oct 19 21:49:27 ubuntu-htpc kernel: [ 17.872362] eth0: no IPv6 routers present
Oct 19 21:49:28 ubuntu-htpc vdr: [1465] Text2Skin: channelInfo display update thread ended (pid=1026, tid=1465)
Oct 19 21:49:28 ubuntu-htpc ntpdate[989]: adjust time server 91.189.94.4 offset 0.273901 sec
Oct 19 21:49:30 ubuntu-htpc vdr-sxfe[1443]: [1456] [input_vdr] No data in 8 seconds, queuing no signal image
Oct 19 21:49:30 ubuntu-htpc vdr-sxfe[1443]: [1456] [input_vdr] using custom "no signal" image /usr/share/libxine1-xvdr/nosignal.mpg
Oct 19 21:49:32 ubuntu-htpc vdr: [1026] switching to channel 1
Oct 19 21:49:32 ubuntu-htpc vdr: [1026] info: Channel not available!
Oct 19 21:49:32 ubuntu-htpc vdr: [1494] Text2Skin: message display update thread started (pid=1026, tid=1494)
Oct 19 21:49:34 ubuntu-htpc vdr: [1494] Text2Skin: message display update thread ended (pid=1026, tid=1494)
Oct 19 21:49:34 ubuntu-htpc vdr: [1026] max. latency time 3 seconds
Oct 19 21:49:38 ubuntu-htpc vdr-sxfe[1443]: [1456] [input_vdr] No data in 8 seconds, queuing no signal image
Oct 19 21:49:38 ubuntu-htpc vdr-sxfe[1443]: [1456] [input_vdr] using custom "no signal" image /usr/share/libxine1-xvdr/nosignal.mpg
Oct 19 21:49:43 ubuntu-htpc vdr: [1026] switching to channel 1
Oct 19 21:49:43 ubuntu-htpc vdr: [1026] info: Channel not available!
Oct 19 21:49:43 ubuntu-htpc vdr: [1513] Text2Skin: message display update thread started (pid=1026, tid=1513)
Oct 19 21:49:45 ubuntu-htpc vdr: [1513] Text2Skin: message display update thread ended (pid=1026, tid=1513)
Oct 19 21:49:46 ubuntu-htpc vdr-sxfe[1443]: [1456] [input_vdr] No data in 8 seconds, queuing no signal image
Oct 19 21:49:46 ubuntu-htpc vdr-sxfe[1443]: [1456] [input_vdr] using custom "no signal" image /usr/share/libxine1-xvdr/nosignal.mpg

Zitat

Original von avalanche99
Doch Doch, MSI VN210 MD512 H

Eine GT 210 passiv von MSI

Na dan hast du nit Sicherheit ein Bild samt OSD, also nicht jammern.

Wenn man dein Log in dem anderen Thread so liest scheitert bei dir einzig und allein das Treiberladen für die beiden DVB-s2-Karten.

Nimm mal nur eine Karte (470er) in den Rechner, schließ da eine Sat-Leitung an, starte den Rechner und poste dann das Log, eventuell must du auch noch ein/zwei Parameter mitgeben beim Treiberladen, zumindest sieht das im anderen Thread so aus.

Gruß
Wolfgang

Zitat

Original von schuetta
bei mir ist das ja so, habe nur eine karte, bild hab ich bei einigen HD sender, OSD natürlich auch ! aber die meisten sender gehen nicht

Wo ist denn die channels.conf her?

Welcher Satellit nur 19.2 OST?

Gruß
Wolfgang

Hab jetzt S464 raus und nur die S470 rein:

Oct 19 22:28:44 ubuntu-htpc vdr: [1228] reading EPG data from /var/cache/vdr/epg.data
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] registered source parameters for 'A - ATSC'
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] registered source parameters for 'C - DVB-C'
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] registered source parameters for 'S - DVB-S'
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] registered source parameters for 'T - DVB-T'
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] no DVB device found
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: streamdev-server (0.5.0-CVS): VDR Streaming Server
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: epgsearchonly (0.0.1): Direct access to epgsearch's search menu
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: femon (1.7.7): DVB Signal Information Monitor (OSD)
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: live (0.2.0): Live Interactive VDR Environment
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: iptv (0.4.2): Experience the IPTV
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] registered source parameters for 'I - IPTV'
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] new device number 9
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] creating IPTV device 0 (CardIndex=8)
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: menuorg (0.4.4): Reorganizes the main menu
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] loading menuorg config file from /var/lib/vdr/plugins/menuorg.xml
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: epgsearch (0.9.25.beta17): search the EPG for repeats and more
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: control (0.0.2a): Control VDR over terminal or telnet
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: xineliboutput (1.0.90-cvs): X11/xine-lib output plugin
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] new device number 10
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] [xine..put] cTimePts: clock_gettime(CLOCK_MONOTONIC): clock resolution 0 us
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] [xine..put] cTimePts: using monotonic clock
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] [xine..put] RTP SSRC: 0x664e5126
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: conflictcheckonly (0.0.1): Direct access to epgsearch's conflict check menu
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: wirbelscan (0.0.5): DVB and pvrinput channel scan for VDR
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: externalplayer (0.1.0): launch external players
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: avolctl (0.3b): Alsa Volume Control
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] plugin 'avolctl' called obsolete function RegisterI18n()
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: text2skin (1.3.1): Loader for text-based skins
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: extrecmenu (1.3-beta1): Extended recordings menu
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: vnsiserver (0.0.1): VDR-Network-Streaming-Interface (VNSI) Server
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: quickepgsearch (0.0.1): Quick search for broadcasts
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] initializing plugin: channellists (0.0.4): Manage your channellists
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] setting primary device to 2
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] assuming manual start of VDR
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] SVDRP listening on port 6419
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] skin "PearlHD" not available - using "classic" instead
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] loading /var/lib/vdr/themes/classic-default.theme
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: streamdev-server
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] loading /var/lib/vdr/plugins/streamdev-server/streamdevhosts.conf
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: epgsearchonly
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: femon
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: live
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] LIVE: initial file cache has 82 entries and needs 381406 bytes of data!
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: iptv
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: menuorg
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: epgsearch
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] loading /var/lib/vdr/plugins/epgsearch/epgsearchcats.conf
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] loading /var/lib/vdr/plugins/epgsearch/epgsearchmenu.conf
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: control
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: xineliboutput
Oct 19 22:28:44 ubuntu-htpc vdr: [1367] video directory scanner thread started (pid=1228, tid=1367)
Oct 19 22:28:44 ubuntu-htpc vdr: [1366] video directory scanner thread started (pid=1228, tid=1366)
Oct 19 22:28:44 ubuntu-htpc vdr: [1371] ERROR: Unable to load cert/key (/var/lib/vdr/plugins/live/live.pem//var/lib/vdr/plugins/live/live-key.pem): No such file or directory
Oct 19 22:28:44 ubuntu-htpc vdr: [1373] [control] gateways thread started (pid=1228)
Oct 19 22:28:44 ubuntu-htpc vdr: [1373] [control] socket opened
Oct 19 22:28:44 ubuntu-htpc vdr: [1367] video directory scanner thread ended (pid=1228, tid=1367)
Oct 19 22:28:44 ubuntu-htpc vdr: [1366] video directory scanner thread ended (pid=1228, tid=1366)
Oct 19 22:28:44 ubuntu-htpc vdr: [1374] Remote decoder/display server (cXinelibServer) thread started (pid=1228, tid=1374)
Oct 19 22:28:44 ubuntu-htpc vdr: [1374] [xine..put] cXinelibServer priority set successful SCHED_RR 2 [1,99]
Oct 19 22:28:44 ubuntu-htpc vdr: [1374] [xine..put] Binding server to 127.0.0.1:37890
Oct 19 22:28:44 ubuntu-htpc vdr: [1374] [xine..put] Listening on port 37890
Oct 19 22:28:44 ubuntu-htpc vdr: [1374] [xine..put] Listening for UDP broadcasts on port 37890
Oct 19 22:28:44 ubuntu-htpc vdr: [1374] [discovery] BROADCAST: VDR xineliboutput DISCOVERY 1.0#015#012Server port: 37890#015#012Server address: 127.0.0.1#015#012Server version: xineliboutput-1.0.90-cvs#015#012#015
Oct 19 22:28:44 ubuntu-htpc vdr: [1372] EPGSearch: conflictcheck thread started (pid=1228, tid=1372)
Oct 19 22:28:44 ubuntu-htpc vdr: [1370] streamdev server thread started (pid=1228, tid=1370)
Oct 19 22:28:44 ubuntu-htpc vdr: [1370] Streamdev: Listening (VTP) on port 2004
Oct 19 22:28:44 ubuntu-htpc vdr: [1370] Streamdev: Listening (HTTP) on port 3000
Oct 19 22:28:44 ubuntu-htpc vdr: [1368] section handler thread started (pid=1228, tid=1368)
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] [xine..put] cXinelibDevice::StartDevice(): Device started
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: conflictcheckonly
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: wirbelscan
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: externalplayer
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] plugin 'externalplayer' called obsolete function RegisterI18n()
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: avolctl
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: text2skin
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] text2skin: loading /var/lib/vdr/plugins/text2skin/anthra_1920_FS/anthra_1920_FS.colors
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] parsing /var/lib/vdr/plugins/text2skin/anthra_1920_FS/anthra_1920_FS.skin
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] text2skin: loading /var/lib/vdr/plugins/text2skin/anthra_1280_OS/anthra_1280_OS.colors
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] parsing /var/lib/vdr/plugins/text2skin/anthra_1280_OS/anthra_1280_OS.skin
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] text2skin: loading /var/lib/vdr/plugins/text2skin/PearlHD/PearlHD.colors
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] parsing /var/lib/vdr/plugins/text2skin/PearlHD/PearlHD.skin
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] text2skin: loading /var/lib/vdr/plugins/text2skin/anthra_1920_OS/anthra_1920_OS.colors
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] parsing /var/lib/vdr/plugins/text2skin/anthra_1920_OS/anthra_1920_OS.skin
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] text2skin: loading /var/lib/vdr/plugins/text2skin/anthra_1280_FS/anthra_1280_FS.colors
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] parsing /var/lib/vdr/plugins/text2skin/anthra_1280_FS/anthra_1280_FS.skin
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: extrecmenu
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: vnsiserver
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] VNSI: VNSI Server started
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: quickepgsearch
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] starting plugin: channellists
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] setting current skin to "PearlHD"
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] loading /var/lib/vdr/themes/PearlHD-default.theme
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] remote control LIRC - keys known
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] switching to channel 1
Oct 19 22:28:44 ubuntu-htpc vdr: [1228] info: Channel not available!
Oct 19 22:28:44 ubuntu-htpc vdr: [1385] Text2Skin: message display update thread started (pid=1228, tid=1385)
Oct 19 22:28:44 ubuntu-htpc vdr: [1383] VDR VNSI Server thread started (pid=1228, tid=1383)
Oct 19 22:28:44 ubuntu-htpc vdr: [1384] LIRC remote control thread started (pid=1228, tid=1384)
Oct 19 22:28:44 ubuntu-htpc vdr: [1382] extrecmenu worker thread thread started (pid=1228, tid=1382)

Aber das no DVB device find ich nicht so gut

Zitat

Original von avalanche99

Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.045461] cx88[0]: subsystem: d464:9022, board: UNKNOWN/GENERIC [card=0,autodetected], frontend(s): 0
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.045463] cx88[0]: TV tuner type -1, Radio tuner type -1
...
Oct 19 21:49:19 ubuntu-htpc kernel: [ 9.226501] tuner 4-0068: tuner type not set

Alles anzeigen

Die Zeilen sagen doch schon alles, oder was meinst du Wbreu? Aber da du ja einfach unseren Treiber mit einem uns unbekannten überschreibst bist du da auf dich gestellt.

Gerald

Zitat

Original von gda

Die Zeilen sagen doch schon alles, oder was meinst du Wbreu? Aber da du ja einfach unseren Treiber mit einem uns unbekannten überschreibst bist du da auf dich gestellt.

Gerald

Nabend Gerald,

genau die habe ich gemeint.

Ich habe hier in meinem Umkreis auch einen Rechner stehen mit einer 464 und einer 470er drinnen. Mit dem Paket von Tevii laufen die einwandfrei, wenn man die passenden modul-Parameter für die Karten mitgibt. Jeweils einzeln laufen sie ohne Parameter für den cx88.

Inwieweit die 464 schon in anderen Repo's ist, weiß ich nicht, laut dem Log kennt er sie gar nicht, da das autodetecd fehlschlägt.

Gruß
Wolfgang